Best Bicycle Wall Mount Horizontal

Mount 17 Aug 2022 10+ Comments Open

1. Dirza Bike Wall Mount Storage

Dirza Bike Wall Mount Storage

Their first priority is your satisfaction. If you have a problem, just leave a message and they will find a solution that will make you happy. The length and angle are adjusted. The bike rack can be adjusted to fit different bicycle frames with the help of a hook and the angle can be adjusted from 0-360 degrees. Their bike hook can save space, but also allow the bike to be placed at a certain angle and position that you are happy with. The garage bike rack has a unique feature that it can be folded and adjusted in length. Put the beam down and put the bike on it. It can be folded up when not in use. Anti-scraTCH and resistance are two things. The sponge protects the hook from scratches. You can use with confidence any of the rack types. The bike hook is protected from rusting by powder coating. STURDY: The bike storage rack is made of thick steel. The bike rack weights up to 2.6 lbs. It holds bikes up to 66 lbs/30KG when 4 screws are installed. It's strong enough to hang most bikes. It's very easy to install a garage bike rack with the included tools and screws. It can be done with a drill and screwdriver. Unless there are wooden stud behind the plaster wall, do not install on it. It's very easy to install a garage bike rack with the included tools and screws. It can be done with a drill and screwdriver. Unless there are wooden stud behind the plaster wall, do not install on it.

Brand: Dirza

👤I wanted to mount my Trek Mamba 29'er Mountain Bike on this bicycle rack. The weight is 42 lbs. Issues were noted. There were four mounting bolts, but no Allen Wrench to tighten the bolts on the steel collar that goes into the wall-mount. 2. The mounting plate is supposed to be mounted into a wall stud. The mounting holes are different at the top and bottom of the mount. You can only mount the rack using one top and one bottom, or you can attach a wooden backing plate to the wall and mount it to the backing-board. 3. The mount for the top rail/cross-bar and the inadequately- knurled post stem was mounted into the mounting brackets, and the plastic sleeve on the mount was tightened as tight as possible. There was nothing that could be done to prevent this, as the cradle post had no high points to adequately bite into, and hold the bike in the desired position. There is a If the weight of the bike is equal from front to rear, but not equally balanced, the cradle won't hold it's position. An aluminum-framed bike such as mine was too much for the rack and it went into the trash can.

👤I have two bikes, a 30lb mtb and a 25lb BMX bike. They are wide to catch a single stud. I used different screws andanchors to catch the other 2 bolts that were rated for 30 lbs each. The other thing is that if you position the bike in a way that you don't want it rotating, you have to tighten the clamps all the way shut.

👤I just installed 3. There is a Can the distance from the wall be adjusted? It's easy to get the bike on and off the rack. It's easy to install the bike. Only 2 of the holes in the mounting plate can touch the stud. Instructions said to use wall anchors for parts that aren't touching studs. None of the 3 came with wall anchoring. My husband drilled holes in the center of the brackets. It would have been nice if it had come that way.

👤These are supposed to be used for mounting into a wall. Installation instructions show the anchors. The anchor sets are missing.

👤The bar is at an angle because I have a girls bike. The hook has to be at an angle because I want my bike to be somewhat straight on the wall. I screwed in the rack as tight as possible, and the rack would slide if I hung up the bike. This hurts. I will be returning it because I am sick of dealing with it.

2. Qualward Hanger Bicycle Cycling Storage

Qualward Hanger Bicycle Cycling Storage

Hang the front tire on the bike rack to load it. Space Saving is a horizontal wall mount for a single bike to save floor space. There are bikes on the wall. One bike rack package is just 1.1lb, it's made of heavy duty scratch resistant steel, maximum hanging weight is up to 220lb. 3 x bike pedal rack and 6 x bike wheel hanger are equipped with screws, which prevent the bike from rotating down and protect walls from dirt and damage. Installation is easy, you can mount the hanger on brick, wood stud, or even on a drywall with a particular anchor. No more turning the handlebars. Bike storage in home, office, garage, apartment or retail display is ideal. It is built to hold all your bikes and last. There is a US patent pending. All rights are reserved.

Brand: Qualward

👤The hardware is made of thick steel and I think it will last a long time. The installation was difficult. The tire rests are difficult to mount since they end up being in a location where it was just drywall, and the pedal mount piece is easy since you can mount it right to a stud. Attach the cross board to the tire hardware. See the picture.

👤The product works well and is better than the others because it allows the mounting holes to hit a stud. The others won't. The mounting holes on this one are easy to install. The pedal hooks are rubber coated and I really liked it. I would have given a few stars. The hardware is junk. Do not use it. You have been warned. The screws are cheap and bend, and the plastic anchor is brittle, so it will break. The shelves for the tires need anchors.

👤Unless you measure and remeasure one million times, you need two people to install. Do you dislike someone? They need to hold the bike in position while you measure and remeasure before drilling into the wall. I almost threw my girlfriend's two wheeled bike in the trash because I was so angry with her for having a heavy mountain bike. The installation was not bad. The bikes look great hanging, one above the other in the garage, but I mark up the wall whenever I take them down or put them up the tires. They started coming out of the wall after about 2 months. The tires were replaced with something stronger that kept them away from the wall. These are garbage now.

👤It's a great way to hang your bike. It makes a cool idea that the bike is being held by nothing on the wall. It's perfect for my storage needs. It made my workroom more fun. The quality was great and I saw the balancing act that it did. There is a Also, note: I usually don't use the screws provided when they are cheap, but I was very disappointed in the anchors. I assumed that they wouldn't have gone cheap on the screws and anchors for a fixture like this. The screws were stripped before I got them in and the anchors broke when I screwed them in. If you don't take that into account when ordering, it will hold me up.

👤This is a great way for me to keep my regular bike at the ready and within easy reach, while still keeping my other bikes at the ready. I used to keep three bikes, but now I have five. The hardware is well made. The rubber coating on the pedal hook is very strong. The wheel trays are small, but they do a good job. The screws and anchors are better than the Chinese ones. If one pre-drills the holes for the drywall anchors, they are good enough to anchor the wheels trays. Since the bike's weight is hanging on the wall studs, I made sure to mount the pedal brackets with my own screws. The reviewer said that the screw holes in the pedal brackets are aligned vertically, which makes them superior to other versions. I agree. The screws will be biting into the wood if you hit a stud. I have had my regular bike in and out of the rack many times, and it has become second nature to me. I have added a bungee around the pedal to make sure the bikes stay in the brackets in the event of an earthquake. I have been able to get my car into the garage with the help of this set. Imagine that!

3. Ibera Horizontal Bicycle Storage Adjustable

Ibera Horizontal Bicycle Storage Adjustable

This large capacity vertical bike rack is made of quality steel and holds up to 2 bikes and a total weight of 80 lbs. The rubber feet keep the bike rack in place. The wall hanger's angle can be adjusted to keep your bike level. The correct height for the tyres should be at least 4 inches off the ground. The mount must be mounted on the side up. A horizontal wall mount for a single bike to save floor space. The weight limit. 38.6 pounds. The sturdy and durable construction made out of aluminum makes this hanger safe for bikes to hang on the wall. The double arm is padded to protect against paint damage. It's suitable for most bike frames. The beam length can be adjusted to fit narrow or wide handlebars. The wall has a mount on it. Unless there is a wood stud behind the wall, don't mount the hanger on the dry wall. If you have any questions about the installation, seek professional help.

Brand: Ibera

👤I am a mechanical engineer, and I feel qualified to evaluate this product. There are many reviews that praise the quality of the bike hanger, but I don't have much to say. I would have made the product from steel and supplied the frame rests or spacers for the wider frames tubing. I would like to defend this product from the many reviewers who thought it was a bad idea to fall off the wall. Did you read the directions? It says to use the anchors only in concrete walls. The complainers stuck the anchors in the wall. I advise you to stop blaming others for your fault. If you don't know what you're doing, you can either learn or read the instructions. There is a picture of a proper installation. The plywood spans between the studs, giving many options for placement. The lower side is in compression, so the 4 screws are on the upper side. There is a Good luck to everyone, and safe ride!

👤I put up three of these in my house and I am very happy. I have some advice. Don't use the screws in the package. Get something better at the hardware store. 2. If you want this thing to be securely mounted, you should put it into a board that is long enough to straddle two studs and mount the whole thing to the wall. The photo is attached for reference.

👤The bicycle hangers should work for most bikes. I like the fact that you can adjust the hangers to fit different sizes of bikes, and that is something that is common on many newer bikes. I bought two of these. The padding on the arms of my steel frame bike is fine, but I decided to add a piece of old inner tube over the grey plastic parts for the one I am using with my carbon frame, because the top tube is wider than the padded part between the hard grey plastic pieces. I will probably add inner tubing to the second cradle. I used a board that was 36 inches long and T-nuts to mount the hangers onto, I attached the boards to 2 studs each for support. It allows for a place to put clothes hooks.

👤These are the racks that I like the most. We used a mix of plaster and drywall on the wall, but the stud was located exactly where we needed it, so it was easy to install, though the spacing of the screw holes on the top might be too wide for some studs. Our house was built in 1912, so we might have had an actual 2” wide stud. I am docking it for a couple reasons. The o-ring on the included strap for stabilizing the front wheel is not the same as shown in the video. It's hard to get tight if you don't have the o-ring. There are two more There were 5 washers in the hardware pack. The instructions show the small washers being used with the two Allen screws along the arm, but there is no mention of the other three washers. We assumed they were to be used with the wall mount screws, so we added it to your instructions. The listing picture shows 3 washers. There are 3 more When you only need 2, the listing shows 3 allen screws. There are four The screws were not in working order. What reality would these work in? It would make perfect sense that the listing shows lag nuts. The countersunk screws are useless because they have to be flat against the wall mount. I found some cap screws from my own collection.

4. Bike Rack Garage Solid Steel

Bike Rack Garage Solid Steel

Measures 2 by 8 by 15 inches. A wall storage rack can hold up to 4 bicycles. Industrial steel is made from solid steel and welded together to hold your bikes. The powder coating supports up to 200 pounds. The rubber-coated hooks hold bikes by the wheel with a secure grip. It is easy to install. Quality mounting hardware is included. The wall stud spacing is standard. StoreYourBoard in Troy, Virginia, created the patent pinching design. StoreYourBoard in Troy, Virginia, created the patent pinching design.

Brand: Storeyourboard

👤The rack is sturdy and easy to install. Even if I alternate the orientation, the spacing isn't great for my mountain bikes. I have 2 adult bikes and 2 kid bikes.

👤The bike rack is easy to install. The rubber coating on the hooks tore off as soon as we added the bikes.

👤Quality product that does the job, I just wish it was a little wider with the hooks being more spacing apart so the bikes don't entangle with each other.

👤I needed to organize my bikes to not take up too much garage space.

👤It's very easy to find them, level them, drill them holes, and send them off. It's a big deal!

👤The rack is easy to install. It doesn't hold the bikes securely. I bumped a bike and it fell off and hit me. I will not be using it anymore.

👤This rack is very strong. This is a good place to store your bikes.

👤It works like a charm because it is easy to install.

👤The hooks are tight together. It's nearly impossible to get out the two middle bikes without banging on the other bikes. Don't recommend.

5. Stalwart Storage Bicycle Foam Bike Accessories

Stalwart Storage Bicycle Foam Bike Accessories

Hardware and instruction are easy to use. The bike wall mount rack is easy to install. When parking your bike at the end of the season or simply done riding for the day, store your bike easily with the Bike Rack from Stalwart. The bike hanger is practical and sturdy. You can fold the brackets up so that they are parallel to the wall and out of your way when not storing a bike on it. The Stalwart Bike Wall Mount is a lightweight design that protects your bike frame from sliding. It is suitable for all types of bikes. Attach the bicycle mount to a wall stud in your garage, at work, or in your house and keep your bike handy and ready to ride. All hardware is included to make sure your bike and mount are secure. There is a product with dimensions 13 25 inches x 11 inches. The weight capacity of the wall mount is 50 lbs. The absolute best price and value on their entire line of products is what they are committed to. Also, note: Only Bike Rack Wall Hooks by Stalwart are genuine and this is an exclusive product.

Brand: Stalwart

👤This thing is crazy. I gave my coat of black to match the wall I hung it on, so don't let the color fool you, it is definitely silver/grey when it arrives. The screws are thick and long enough to hold my bike. It's high quality at the right price point.

👤It is easy to install and looks nice. 2 stars off for the included hardware screws. The wood screw is really bad. A picture of the included screw after 3 seconds with the drill. I spent 45 minutes trying to get the screw out of my wall, and lucky to be able to do it. The screw is made of clay. There is a I would feel the need to leave a less than perfect review if a 25c screw left a bad taste in my mouth. Don't use the included sewer, you will be reprimanded immediately. Don't make the mistake I did. I read all of the bad screw reviews and thought they were dramatic. They were not.

👤If only my bike had a straight handlebar fit, I could get it in the hooks, but the only way I could do that was to turn the front wheel away from the wall. The hooks are supposed to fold up against the wall when not in use, but when I tried to do that, they just fell down. The rack hooks were removed and will look for a solution. It might work for smaller bikes since it's priced right.

👤You should replace the Zinc screws with the ones that come with the STAINLESS STEEL screws. The screws strip completely when I use them. I had to hold the screws the rest of the way in. When I want to move the racks, I'll have to drill them out.

👤I was worried this wouldn't hold my bike. I was not sure if it could hold all the weight. I didn't check until I got it. I have had it for a month and it seems to hold my bike perfectly. I put it on the wood beams in my garage. I am worried if someone puts more weight on it, it may cave, but so far it has been holding it down. There is a I have a female bike. I had to install it at an angle. If you're looking for a basic bike mount, I recommend it.

👤It's not much to like. Poor quality screws. Not very heavy duty. The top screw holds the weight. The bottom screw will snap off if the top screw goes. I added a new hole in the middle and installed larger and longer screws. Does not stay out of the way when not being used. When you hang your bike on it, you are moans and groans. I own a bike that is 28 pounds. If you install better screws and don't care if they stay in the down position, it's fine. Would not buy again.

👤One of the screws had a broken tip and I was a little frustrated. When I hung a bike for the first time, the screw broke near the head, and I was frustrated. It didn't fail later and fall on someone, so I should be happy. There is a It doesn't stay in the horizontal position. I don't know if it's a bad design or if it's a defect. It seems like there is nothing to hold it up. I can push it against the wall and it will fall down.

6. Venzo Bicycle Cycling Storage Brackets

Venzo Bicycle Cycling Storage Brackets

If you have a problem with your purchase, they are happy to give you a Refunds or a Replacement. If you have any questions or queries, please get in touch with them and they will be more than happy to help. Only install bike wall rack on a solid stud, beam, masonry or concrete wall. Unless there is a strong wooden stud behind the wall, do not install on it. You can stack multiple bikes on the wall, instead of hanging 2 bikes, you can hang 3 bikes on the same size of wall at the angle of 45 degree. The max loading weight is 20 or 45 lbs. There is no grooming facility. The wheels are moving. It's no longer possible to accidentally knock the handlebars or wheels. Quality: Excellent. The hook is made of heavy duty steel. The hook is made of rubber. The included screws are of good quality. The pedal hook is safer than other types. Installation is easy, you can mount this hanger on brick, wood stud, or even on a drywall with a particular anchor. You can watch the video in the listing. The weight is 260g (0.57 lbs). You can order now and pay free. They can provide a life time warranty for their product. It was made in Taiwan.

Brand: Venzo

👤Fantastic! There is a Cyclists joke about the Formula. The formula is N + 1 The correct number of bikes to own is N + 1; where N is the number of bikes you currently own. Get it? You may end up with more than one bike if you hang around the community for a long time. I would love to say there is one bike that can do it all. There is not one bike that can do it all. There is a I wanted to be able to hang my primary rides in the studio. A mountain bike and a road bike. The Groad Bike has two sets of wheels and is an Orbea Terra. One set is 700c with 28c road slicks and the other set is 27.5/650b with 42c Gravel Tires. There are a lot of options when it comes to mounting bicycles. There are mounts to hang the bikes from the ceiling. I was looking for a solution that was cheap and easy to use. There is a The vertical mounts allow you to store several bicycles in a small space, but the bicycles still protrude into the room space a fair amount. The ceiling wheel hangars take a lot of space and can cause issues with Mountain Bike suspension components and dropper posts when the bike is left hanging upside down. The concept of the bicycle pedal wall mount was found after a bit of searching. The product looked good to me. It was made of plastic and had wheel trays that were color matched to protect the walls from dirt and rubber marks. They were not in my price range at $70 per set. That is $70 per bike. There is a A little more searching. The Venzo Bicycle Pedal Wall Mount is on Amazon. There were some good reviews. The product looked strong in the photos. I was surprised to see that I could buy three for $28. It was sold! I waited for my order to be placed. There is a The package arrived. The pedal mounts are made of solid steel and have a tough Rhino-Liner like coating to protect them. There are no instructions, but the package included wall anchors and screws. Okay. Let's figure it out. I wouldn't think about mounting a bike to the wall with only anchors. I wanted to get these bikes up on the wall. There is a Measure the height of the lower mount. I had to hold the bike up against the wall, hold the hangar in one hand and use a pencil to write on the wall. The rubber marks on the wall were caused by the tires. The stud finder can be used to find the studs. 3 Match the height marked in step 1 with the actual stud locations in step 2. The holes should be drilled. First problem! It was obvious that only two of the screw holes would match the stud. The anchor would have to be a drywall one. 5 Attach the pedal mount to the wall. Did I mention how strong these things are? 6 pedals and 6 cranks. Hang that sucker up! It looks great, that was easy. The center of gravity is not at the bottom of the bike's frame, which is causing it to slip on the wall. There are more rubber marks on the wall. The workshop will make some simple wheel shelf/wall protectors. The wheels should be penciled in the position. Attach the protectors to the wall. It's Bingo! Summary The setup is easy to install and it looks great. There is a The price is a pros. The price is too high. The plastic variety sells for $70 each. Make it happen. The mount, your cranks and your pedals are protected by a very solid steel with a Rhino-Liner like coating. There is a There are no instructions. 2 of the holes will be secured by screws.

7. Foldable Horizontal Bicycle Bicycles Mountain

Foldable Horizontal Bicycle Bicycles Mountain

The maximum tire width is 20′′ and the recommended wheel diameter is 29′′. There is free up floor space. The bike rack is horizontal. It frees up garage floor space by keeping bike off the floor. It's perfect for garage, home, indoor shed. It's best to install on concrete or masonry walls. It must be screwed directly to the stud. The arm of the wall mount bicycle hanger has a rubber covering to protect against bike paint damage. This rack can hold up to 44 pounds of load capacity. Their first priority is your satisfaction. If you have a problem, just leave a message and they will find a solution that will make you happy.

Brand: Noa Store

👤I might be weird. When you spend so much on a mountain bike, you want to keep it in the garage or shed. I have it mounted in my room. I can see my bike on my wall when I'm laying in my bed, like at a bike shop. It was easy to mount. You should buy this for your wall if you buy this for a friend. The wife will say no. She is at work. I am having a cocktail and staring at my Gary Fisher 29er.

👤I like the rack for storing my bike. It folds out of the way when not in use, allowing more space in the area. The included bolts were a con. They were for masonry work. I had to buy screws to put the rack on the wall. I am very pleased with this product. I think the purchase of this rack is a good idea.

👤The bolts and screws included in this came with no instructions for mounting. I tried to mount my Specialized with wall anchors, but no luck. I will be returning with a new mounting system and some patching material.

👤The screws/anchors that were used to install on the interior wall were not instructions. The best bet is to mount into the studs. The mount seems to have been made well.

👤The rack is not worth much. The item has no instructions. There is a video posted on Amazon. The video did not show all the steps. The rack does not fit against the wall. It can't get it tight. The wall was ripped out. I can't figure out how to mount it to the wall. Very disappointed.

👤Bolts are not for the construction of the wall. It will hold 45 lbs. I have a mountain bike. It has a bend to it. I am worried about it. The weekness and bolts are worthless.

👤I used my own lag bolts and put a stud in the bike, but it took about 10 minutes to get it up and hanging. It was great to be able to put it up.

👤The item arrived as pictured and stated in the discription, but it does not hold much weight. I have a bmx bike that is 26 lbs and it is bending. I wouldn't recommend it for that. It would be ideal for a kids bike. I was not impressed with it and will probably replace it with something better. Not bad for the price, but can not hold an adult bike.

8. Stormann Garage Horizontal Storage Bicycle

Stormann Garage Horizontal Storage Bicycle

It's easy to install on your bike, just loosen the lock on the bike and tighten the screw, it's a great choice to replace the damaged bike kickstand. It's the perfect accessory for your bike trips. The bike hooks for the garage are designed with a special coating to prevent accidental cracks or scratches. The hooks can hold up to 50LB. There is free up floor space. The bike rack is horizontal. It frees up garage floor space by keeping bike off the floor. It's perfect for a garage, home, orshed. It's verSATILITY. The bike hanger can be used indoors and outdoors for all kinds of bicycles. You can use it as a bike repair stand. It's a good choice for storing and holding your bikes. It is easy to install the bike rack by one person using common household tools. Make sure that you install the bicycle hanger on solid walls only. If you have any questions about their products, email them and they will respond as soon as possible. If you have any questions about their products, email them and they will respond as soon as possible.

Brand: Stormann

👤It's what you see. It is easy to install. There are 2 sets for kids and 2 for adults. The arms only go up and down when not holding a bike. You have to figure out where the hooks are to balance the bike on the wall. It was easy on a bike.

9. Bike Wall Mount Horizontal Bicycles

Bike Wall Mount Horizontal Bicycles

Keep your garage or indoor space tidy and free up your floor space by storing your bike in a convenient location. Their wall hanging solution to bike storage is great for apartments, homes, garages and sheds. Most bike types have a storage system. The bikes can hold up to 22 kilogram. Not suitable for bikes with wide handlebars (31 inches / 78 cm) or fat bikes. It is safe and secure to store your bike in a horizontal position. The wall mount is made from strong steel. The bike arm locking mechanism uses a reliable gear system. The angle of the wall hanger can be adjusted to keep your bike level. Installation instructions and mounting screws are included. The push button lock system ensures that the frames can be secured, and the cradle arms ensure that all the frames can be accommodated. A secure push button mechanism secures the extendable beam from 8.7 inches up to 12.6 inches. The Armcradles are made from soft TPR rubber material that will not scratch your bike. The frames are protected and the tube shapes are not marked or moved. To prevent front wheel from knocking against your wall, you need a rope that is strong and elastic. If you have a problem with your purchase, they are happy to give you a Refunds or a Replacement. If you have any questions or queries, please get in touch with them and they will be more than happy to help. Only install bike wall hanger on a solid stud, beam, masonry or concrete wall. Unless there is a strong wooden stud behind the wall, do not install on it.

Brand: Pro Bike Tool

👤The rack is nice. It is built out of quality materials and has a lot of flexibility. The mounting points for this rack are a bit odd. They provide you with 3 small screws and masonry wall anchors, when they should have provided a beefier faceplate and 2 lag bolts to mount into a stud. My solution was to take a piece of scrap wood and mount it vertically to a stud using 2 heavy duty lag bolts, then mount the original screws to the wood. The rack gets 5 stars from me.

👤I was concerned my handlebars were too long for your wall mount, so I sent Chris a letter. To make sure they fit, I put a 2x6 board on my wall stud and then put a wall hanger on the board. It allowed plenty of room for the handlebars. There is a I had a problem attaching the hanger to the studs behind the plaster board. There is a one and three-eights inch distance between the wall hanger's two holes. The wall thickness is one and one-half inches. There is no time to get a strong attachment with only a quarter inch overlap. The instructions give a good idea of how to install the hanger on the wall. They warn that the plasterboard won't support the hanger. Very true. The wall stud's width is insufficient. Instructions to attach a 2x6 to a wall stud and then attach a hanger to that board were added by me. There is a The cradles for the bike are red or black, which is a point of favor for the Pro Bike system. The shape of your cradles allows room for the control cables if the bike has them beneath the cross bar. Great feature. There is a Thanks for your help. I hope my experience is useful to others. You have a good product.

👤Highly recommend this bike storage system. Enough about how great it is. I want to know how to install it. You probably do as well. I installed 3 holders. The first thing to do was to find the studs. To double check the exact location of the stud, I used a finishing nail and hammer to find the sides of the stud. I was glad I did because some of the stud finders locations weren't right. There is a You can mount the 3 holes of the brackets into one stud with longer screws than those that come with the kit. Some people have said this works. It didn't seem like it would be stable. I decided to mount a 2x6 across two studs. A 2x4 is not wide enough. I cut the 2x6's 22” long so they fit over the end of each stud. I used lag screws to attach the 2x6's to the studs. I used lag screws on both ends. There is a You will need a impact driver to get the lag screws into the stud. A regular drill won't do it. If you don't have an impact driver, you can always use a sockets wrench. After I tightened the lag screws down, I had to use a sockets for the 5/16 lag screw. I measured the bikes with the holder to make sure there was enough space between them. The measurement resulted in a spacing of 40” from the top of one board to the top of the next board. It was perfect for my bikes. Different spacing is required for your bikes. The wall mounts are perfect. Unlike other systems that are horizontal, these allow you to adjust the arms to fit the different types of cross members as not all bikes are alike. I think they are worth the money. The 2x6x8 was $11 and the 12 lag screws were $9. If you decide to purchase these, I hope this helps.

10. Bike Rack Hanger Wall Mount

Bike Rack Hanger Wall Mount

The bike wall mount is made of high quality, it has a maximum hanging weight up to 150lb, and it can be mounted on brick, wood stud and dry wall. Space Save using a bike wall hanger lets the bike off the floor and free up more valuable floor space to keep your garage clean and tidy. Most bicycles are compatible with their wall mount bike storage system. The stylish smile design is highly decorative and adds an artistic flavor to your room. A bike wall holder is a work of art. Bike storage in home, office, garage, apartment or retail display is ideal. The bike wall hanger is easy to install. The bike wall brackets are easy to install and no assembly is required. The pedal of the bike or pedelec can be inserted into the bike storage suspension. The bike fixed hook is an ideal choice. The bike wall racks are a great solution for storing your bikes. If you are looking for a sturdy and efficient bike rack, then this Gootus bicycle wall mount is what you want. They will be happy to help you if you have any questions.

Brand: Gootus

👤I love this product. The thought of hanging bikes on the wall made me cringe. The product doesn't intrude into the needed garage space. The pedal should be screwed into the main wall brackets, as it holds most of the weight. I didn't have any problems, but I wouldn't trust the types of bolts and anchors that are used for the main brackets. The metal trays for the bike's wheels can be used if there's no stud available, as there's little weight or pressure against the metal wheel tray.

👤The holes are too big for sheet rock screws. When driven into a stud, the screws will twist off. Hold the bike pedal on the wall and write on it. The stud has angle screws with washers into it. Put the bike on the ground with the bottom of the tires level with each other. Attach each tire support with sheet rock anchors, screws and washers. There is a game called bingo.

👤I found a similar one that cost twice as much. I went back to get a second one because I loved it so much. I'm excited to find a similar one. It is easy to hang the bike because it is on the wall. I covered the tires with a plastic bag to prevent them from being damaged. I think it's a good idea. Take a look at my pics.

👤Storage hanging by a wheel is more compact than hanging by a wall. The bike hangs at a 15 degree angle off the wall by one of the pedals. There are two brackets on the wall. If you are mounting on a wall, you need to cut the sledgehammer into the wall stud. The support for the bike is done by the hanger brackets, but they are not strong enough. If you attach a wall stud, it will be fine, even if you install only on a masonry wall. The tire brackets can be used with sheetrock anchors since they don't hold the weight of the bike. It was very easy to get the bike off.

👤I like this product a lot. I put it on my wall. It took about an hour to complete. The job should take around 10 minutes for someone who knows how to use simple tools. Most things take a while for me because I don't consider myself handy. I usually get it right with enough time. I like the scratch resistant material, however, I feel like if the bike hits the mount hard enough it can scratch the bike so I'm really careful when placing it on the mount. The material is strong and heavy. It is very sturdy and won't fall or break the wall when installed correctly. This product is very good. The product states that the bike parking rack should be installed on a solid brick wall or concrete brick, but not on unsupported wall surfaces. Don't use this product if you don't know how to use anchors and plugs, don't have concrete walls, and don't know how to locate a wooden stud. You want the bike to fall from the wall and not hurt anyone. I really like this product. I needed to clear up my hallway because I am 6'3" and have a bike. The bike cleared up a lot of space on my wall. This product is recommended.

11. Session Bike Profile Indoor Bicycle

Session Bike Profile Indoor Bicycle

It's easy to install, you just need an electric drill and a level to make sure it's lined up in a row for mounting on the wall. The wall collapsed in 16 inches. Installation of paneled wall sheeting must be located to solid structures. All installation hardware is included. PREMIUM QUALITY: The bike wall mount is made in the USA and has a rich black powder coating finish. The bicycle wall hanging kit is made from 3mm thick high grade steel. Space and FEATURE are subcategories. The wall bike hanger has a unique andadjustable arm for pedal which allows for angle adjustment while mounting the bike. This assures a lower profile and maximizes the space savings. Session Bike horizontal mount requires no contact with the bike frame. It is the best bike hanging solution. The design of these bicycle wall mounts have a wheel cradles with hooks to hang your accessories. The bicycle wall rack is safe and secure. It is suitable for all types of bikes. The bike hanging kit comes complete with all the hardware and accessories you need to hang your bike on a wall. Fix this bicycle mount to any wall in your garage, home, or work place and keep your bike handy and ready for a ride. Session Bike is a company that is driving innovations to add value to their customers lives. If you are unhappy with their bike hangers, please get in touch with them and their customer service team will get to work on it immediately. Click here to add to cart. Session Bike is a company that is driving innovations to add value to their customers lives. If you are unhappy with their bike hangers, please get in touch with them and their customer service team will get to work on it immediately. Click here to add to cart.

Brand: Blue Eagle Labs

👤I bought these wall mounting brackets because of other photos on Amazon. I'm definitely worth the money. The bikes look great on the wall in my apartment, and people always compliment it. Installation can be difficult. I would give you a hand so they can mark it when you hold the bike on the shelves, as they will have to mark it while you hold the bike on the shelves. I used better wall anchors from home depot. The brackets and shelves are covered in black paint. The bicycle is out of the way. It puts the handle bars up at the ceiling and tilts the bike so that you can see it. You can mark the walls with the tires which come off with dish soap and water, but that has nothing to do with the actual product. A small level, measuring tape, drill & drill bits, and a number 2 philips head screw driver were needed. There are 6 anchored screws that hold up the shelves and brackets.

👤I like the mounts. I wanted to hang my bikes over my drums. The mounts make my bike lean too far. They grab the perfect spot on one set of pedals, but I'm not as comfortable on the other. The arm might be able to grab the pedals by the crank arms. There is a It's easy to install and stable.

👤The idea of having a hinge to make it adjust was the appeal. The product is useless because the hinge doesn't stay fixed, even after 2 hours of measuring and drilling holes in the wall. Flops down despite the little screw being tightened to the max.

👤Bike mounts work well. It all will work if you take your time and get the pedal mount at the right height and fore position. There is a It will be difficult to get the pedal hooked and unhooked if the pedal mount is too low or high. It needs to be mounted at a height so that it angles down on the same plane as the pedal.

👤I don't know if it's because I have big pedals on my bike, but the bur is a perfect mount, it's not noticeable when it's not in use.

👤This is a great design. The space we get back from lifting our bikes is wonderful. It is very easy to install and support our bikes. We ordered one to see how it would do, but we decided to get two after all. There is a We returned the other bike racks that we had tested. This one was the winner.

👤I used some wall anchors that looked a bit more substantial but they all went up and are working out great. Lower wall mount hooks are great for holding things. There is a They planted 2 trees through their program.

👤I pictured it hanging like that. The claw for the pedals may not fit all pedals. I have oneup pedals on my bike.

👤I received the wall mount bases for tyre without the pedal hook, but did not receive a reply for many weeks. Without the pedal hook, it's useless.

Summary

What is the best product for bicycle wall mount horizontal?

Bicycle wall mount horizontal products from Dirza. In this article about bicycle wall mount horizontal you can see why people choose the product. Qualward and Ibera are also good brands to look for when you are finding bicycle wall mount horizontal.

What are the best brands for bicycle wall mount horizontal?

Dirza, Qualward and Ibera are some of the best brands that chosen by people for bicycle wall mount horizontal. Find the detail in this article. Storeyourboard, Stalwart and Venzo are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com