Best Bicycle Storage for Garage

Storage 14 Aug 2022 10+ Comments Open

1. Delta Cycle Leonardo Storage Vertical

Delta Cycle Leonardo Storage Vertical

The bike rack garage wall mount is built to last and has quality components that will stand up to the wear and tear that comes with frequent use. Give yourself or a loved one the ultimate bicycle storage solution with their bike rack. The Space Saving Bike Wall Mount securely stores any bicycle up to 40 lbs off the floor. The Leonardo bike rack garage has a hook shape that makes it easy to access bikes. Your next ride is close by. Installation is easy with these bike hooks for garage wall. The peel-and-stick rear tire tray protects your walls. The contemporary design of the anti scratch coated hooks has a rubber coated bike hook. The bike hanger hooks are available in either a premium silver or black powdercoat finish and look great in any room. Over 1 million cyclists trust their bike's in Leonardo vertical bike racks. For over 30 years, Delta has been a leader in bike storage. The A+ customer experience was designed and engineered in the US.

Brand: Delta Cycle & Home

👤These were easy to mount. We used a piece of 1x6 Poplar and created our own steampunk style bar for the rear tire, instead of using the stick on the rear tire mount. They look great in our office.

👤The hook on this rack is so heavy that it's hard to slide your bike onto it. It takes a lot of spinning to properly orient the bicycle because the red padding slides down. The red padding is becoming difficult to use after a few months of use. The mess around the hook has resulted in a lot of scratches on my wall. I bought a second bike with a straighter hook last month and it's way easier and more efficient than the first one. The new hook is so annoying that we fight over it.

👤It is very easy to install a power drill and stud finder. It's not much to say. My son installed it himself. The package had to be opened before the bike could be hung. If it fails, I will update the review, otherwise 5 stars! There is a Dead simple instructions: 1) find wood studs 2) mark where the front tire will touch the wall 3) measure 12 inches above that mark, 4) drill a pilot hole in mark above, 5) line up the rack

👤It does not fit for mountain bikes. The wheel does not sit in the base when the hook is locked around the rim. The tire rubs on the base's side loops when the wheel is towards the top. The base should be centered on the wheel. There is a I bent it to make it fit. Vice grips and a pipe wrench were used.

👤I own a carbon fiber Trek bike. Our apartment doesn't have any building storage so I had to put it in my bedroom. I settled on the $9.78 Delta Cycle Leonardo bike rack. This is a total life saver space saver and I couldn't be more pleased. There is a The bike is mounted between my closet doors and wall shelving, which is about 8 inches of space. To keep the wall from showing the tire scuffing, I used a black vinyl strip and a Mr Clean magic eraser, but any wall paper can be used. No anchors are included in the kit. You should buy a pair of sturdy anchors. The weight limit for the Delta mount is 40 lbs / 18 kilo, so keep that in mind when shopping for a bike rack. There is a I hope it holds up, I couldn't be happier with this!

2. CyclingDeal Bicycle Floor Parking Stand

CyclingDeal Bicycle Floor Parking Stand

The rigid design of the rock solid base allows a secure base for awkward cycles. STABLE: The bike floor rack has been changed. The two holding plates with tire grooves are at an optimal holding angle. The feature ensures bikes are held in the stands. You need to fit 6 bikes in the stand if you put your bikes in different directions. One front and one back wheel. If there is large space, the bikes could be inserted from both sides. Strong. The stand is made of high quality steel. The black finish is powder coated. It is best to use indoors. The front and back plates hold the up holder. The bike holding stability will be affected by the wide holder. The bike stand holders are linked together so it is easier to use. Please watch the video in the listing. COMPATIBILITY: The rack is designed for all wheel size bikes, from the smallest to the largest. The tire width is 2.5. The back of the bikes should be inserted into the hold so that they sit in the front. The bike rack could not be touched by the disc rotor. The bike stand holders may be touched by bike hubs. You can order now and pay free. They can provide a 5-year warranty on their product.

Brand: Cyclingdeal

👤This product is very good. It's heavy, stable, and holds our mountain bikes securely. The video instructions have a bunch of bullocks. If you have two people and are a zen monk, you should not follow those instructions. It looks simple, but only on the video. If you follow them as recorded, you'll end up throwing it away or out your window, which could be fatal for a poor old lady trying to walk her Yorkshire terrier. Poor little Yorkie. To make this easy, build each stand as a separate stand and snap them together. It will be easier to keep everything lined up if you screw in the bolts that hold the sides of the tire holder. I wish someone had told me that before I tried to follow those directions. Maybe my neighbor Yorkie would be a good mother. There is a This is a quality stand and really worth the money we spent on it. It's long enough to fit all of our bikes and holds up when there's only one on the end. I gave this 5 stars, but I removed one at my physicist's request. If you get this stand, you will not be disappointed. Remember the dead.

👤It works great for our bikes. There are three adult bikes and three kids bikes. You have to take your time putting the bikes in. Each child can do it. It helps organize our garage. We preferred this over hanging. How could our kids not get hurt? They couldn't. The hanging or wall ones are great for older teens and adults.

👤We've been tripping over bikes for a long time and this solved the problem after half an hour of assembly. I didn't watch the video and the drawings were not good. If you've ever put together anything from ikea, you can handle this. It's a good thing. It's nothing fancy, but it does the job it's designed to do very well. We needed to put some in front wheel and some in rear wheel first. The bikes fit that simple modification.

👤It is easy to put together, but not level. It works fine for what we need.

👤It's easy to put together. I bought a bike stand. I had to assemble about 15 minutes. I had read that it was difficult to assemble and instructions were poor. I found it easy to assemble the instructions for these people as they are not capable of putting gas in their vehicle. I get a kick out of people bashing a product when it is their lack of ability that is the problem. If you need a nice bike rack at a cheap price, this will suffice.

3. Begona Freestanding Portable Apartment Mountain

Begona Freestanding Portable Apartment Mountain

Backed by 30 days money, the 100% SATISFACTION GUARANTEE. Back. The quality of the bike storage wall mount is guaranteed by them. Any issue with it is available. The Begona bike floor rack can be used in many bikes. The upgrade wide base can fit tires up to 3.74" wide. The bicycle stand is made of high strength steel. The high-quality steel frame is strong enough to hold heavy-duty bikes. The bicycle rack is powder coated to resist rust. cient parking solution You can use the bike rack to easily park your bicycle in a variety of places. No more worrying about where to put your bike in your room because you can put it in the free standing bike rack. One wheel stabilizier strap comes with a bike stand for free. The bike can be parked on the front or rear wheel without damaging the spokes or tires. Push the bike inward until the wheel stabilizer pops out to secure the wheels. Non-slip pads can protect your floor. To ensure a great shopping experience, the Begona bike stand undergoes at least 3 times of inspections before shipment. They will replace or refund you if you don't qualify for the bicycle stand rack. To ensure a great shopping experience, the Begona bike stand undergoes at least 3 times of inspections before shipment. They will replace or refund you if you don't qualify for the bicycle stand rack.

Brand: Begona

👤I own a folding bike. I like it so far. I would like it to hold the bike without leaning it. Maybe it is because I folded my bike. So far, good!

4. Wallmaster Garage Bicycles Storage Vertical

Wallmaster Garage Bicycles Storage Vertical

An awesome gift for Father's Day is the best after-sale service. The Remiawy garage organizers come with a one year guarantee. If there are any garage hangers that are found to be faulty, please contact them. The customer service executive will be at your service willing to help resolve your issue. You can mount the bike rack securely with 4 screws. Before you start, please find the correct height. Valuable space in your garage can be freed up. The rubber-coated hooks prevent bikes from being scratched. HEAVY DUTY The maximum hanging weight is 50lb. It's strong enough for most bikes, like mountain bikes, road bikes, adults bikes and kids bikes. The fixed hook design can prevent accidental release. The quantity is 2 pieces and the Rim is 3.3 inch. The quantity is 2 pieces and the Rim is 3.3 inch.

Brand: Wallmaster

👤They were easy to install. The hooks came with hardware that I did not use. It's a lot easier to install with TapCons. I was disappointed when I went to hang the bikes. If you have a bike with a fatter tire, you might not be able to use these. I had a hard time hanging the flat tires on my bikes. I was able to get the second bike on the wall because I did not drill the hole deep enough on the top screw.

👤The hardware is very good, and the fact that the racks are not on a rail provides a lot of flexibility. It's easy to take bikes off. I could not be happier with this product. If you're looking for a single bike storage solution or multi-bike storage, it's definitely recommended.

👤Great product. If you mount on the wall, please use a dud finder. The stud must be mounted on in order to hold the weight of the bike.

👤The small footprint of the rack is what I like about it. They barely have room on the wall. The stands are not built with thick metal which is easy to upgrade and it is not easy to mount bikes on the rack due to the design and curve of the hook. There is a I would buy again, but I would look at other options before making a purchase of future bike racks.

👤Not much to say about these other than they work well. They are very sturdy, but I did not trust the wall anchors they came with, so I attached them directly to the studs. I don't want to have to fix the drywall in the garage. They were a great value since they were a two pack and I and my wife have bikes to hang. It freed up a lot of space on the floor in my garage, more than I expected. It's very easy to install. These were a great purchase.

👤Not for someone who bikes +3x a week. Taking the bikes off and on is tiring. You have to clean the tires after each ride because they are on the wall. The hooks have very little room. To get the wheel stuck in, you need to go on an angle. My girlfriend won't even bother with getting the bike in and out because I have to wrestle with it. It gets tiring. I used the hardware that came with them and did not mount to studs and they are still hanging, but I think that is why it is more sturdy than other reviewers. I will go back to ceiling hooks if I have any problems with the mounts.

👤I'm surprised nobody mentioned the smell. It smells like a plant. They smell the same after three days in the sun as they did when I opened them. It smells like citronella and burning rubber. I don't want to use these in an enclosed space when they smell so bad.

👤I had a pair of vertical wall bike holders from "Transit" that worked fine for several years but I noticed that the metal hook was getting bent a bit. I had to get a better replacement for that bike after it broke in the middle of the night, and the one next to it fell onto our cars. The Wallmaster product is similar to install, and it looks like the hook that the front wheel is held by is stronger than the other product. If you have a couple of studs to go into, they are trivial to install, but not recommended if you don't have a stud. The screws are not very strong. I used construction screws that were not included in the package. The Wallmaster units are never coming off of my wall, and I hope the hook is stronger and doesn't break like the "Transit" product.

5. Vibrelli Bike Wall Mount Horizontal

Vibrelli Bike Wall Mount Horizontal

Good service. They are behind their products. The bike is built to last. Their service team can help their customers. You can contact them if you have a question. They're happy to help. The bike storage system needs to be installed on a concrete wall or a stud behind it. The bicycle wall mount is a great way to save space in apartments, homes, garages and sheds. The patent pending design works for most bikes. The bike wall mount slides out from the wall to fit narrow and wide handlebars, and the push button design makes adjusting the rack for your bike frame easy. The frame cradles are flexible to mold around the bike frame and won't scratch the paint. The front wheel has straps that prevent it from swinging. This rack is made from welded steel, not aluminum. It can hold bikes up to 55 lbs. Installation is easy to use and follow written and video instructions. Only for installing to wooden studs and beams. If you want to install directly on the dry wall, you should install to the supporting stud/beam. The 10-year manufacturer's warranty is included in the Ironclad Warranty. Cyclists designed the building to last.

Brand: Vibrelli

👤I've had this product for a month and it's perfect. I agree with the reviews that suggest paying attention to the type of wall you have. If this will be a sheetrock installation buy a plank from other reviews. You do not need a 2x6. I fastened the plank to the studs with wood screws 10 x 2 and 10 x 3 and used a stud finder to locate the studs. I used the screws in the package to fix the bike mount. The arms adjust to fit the angle of the frame with the push of a button and the rod adjusts so the bike handlebar fits against the wall. There is a If you have basic tools, you are good to go for about an hour.

👤It is as easy to install as you think, but you have to follow the instructions. You need a bit of masonry if you are going into brick or plaster. You need to be responsible for anchoring this in. I used the hardware provided without incident, but I think it would work with other anchor that are meant to carry weight. There is a It took less than 20 minutes to install. I ride my bike twice a day so there is a lot of moving the bike. The piece is anchored into the wall. The bike is more handsome and my place is more organized and tidy with it up on the wall. I can change the angle of the bicycle with the arms being adjusted. There is a I would hire a handyman or a professional to anchor this into the wall if I wasn't sure I could do it, because it would be disastrous for the wall, pets, or even people. First of all, safety. There is a I cannot recommend this product enough. Excellent design, simple and easy to install. I would give it six stars.

👤I can't recommend this design because of specific installation details. I've had a lot of problems and expenses to get this thing up and stable. The sheetrock was pulled away from the wall and came out completely. I consider myself a competent homeowner. On 8-19-2010. There is a decent rack with utility in many locations. The depth of the arm cups that hold the bike frame is a big plus. The bike and rack are secure, but the pipe that holds the two arms surprised me. The included hardware is bare minimum and bolts are too short. The hole diameter is too small, the bolts are included, but any installation other than the one provided for is going to require boring into the steel plate. I think a cheap mod for Vibrelli would be the ability to lock a bike to the ount.

👤The bike rack can handle wider handlebars than almost all of the other racks, that's what I like about it. I like its design and simplicity. It seems sturdy. How could it improve? There are two ways to do it. It's easier to put three screws into a 2x4 stud hidden behind a wall than it is to put them into it. It's very likely that not all 3 screws will find good wood in the side of a hidden 2X4 because it's more like 1 and 1/2th wide. I assume that the rubber cushions for the bike frame have multiple fingers so that they can work with multiple frame widths. I found them problematic when trying to place a bike onto the frame, since the fingers kind of get in the way and challenge your ideal placement. A simpler cushion design would work better. I still think this is the best rack for bikes, even after researching several other products. Should I ever add a third bike, I would buy another one.

6. Bicycle Ceiling Mountain Adjustable Capacity

Bicycle Ceiling Mountain Adjustable Capacity

Includes a pulley system, mounting system and rope. The bike lift is designed to ceiling mounted for bike storage in garage or other place when it's not used, which can save a lot of space for your garage. The USAGE is VARIOUS USAGE- The bike lift hanging rack can be used for a variety of things, from kid's cycle to mountain bicycle, kayaks, extension ladders, and other gears. HEAVY DUTY Heavy duty iron and nylon ropes are used for the ceiling bike hoist. The bike pulley hanging system can lift up a mountain bike or road bike up to 100 lbs. It's easy to install. The bike hoist is easy to install and ceiling mount. It is easy to hang your bicycle/ladder from the ground with 3 pulley hooks and 45 ft rope. Their hooks are coated and welded to protect your bikes from scratches. It's time to say goodbye to your worries about bike damage or potential collapses. Their hooks are coated and welded to protect your bikes from scratches. It's time to say goodbye to your worries about bike damage or potential collapses.

Brand: Ihomepark

👤Great product. The hoist wheels are wide so they prevent the rope from going into the crack. I had to contact the customer service because my rope was a little shaky. They only offered a $10 Amazon credit for me to purchase my own rope, instead of sending me a replacement rope. The rope I got was larger than the bike hoist I had. I made it work. I like the fact that the rope I bought on my own is a quarter-in size, it makes it easier to lift the bike to the ceiling. The other type of bike hoist that I used to have was of a lesser quality, but I know this is a great product. There is a I highly recommend that you mount this onto a 2x4 and then mount the 2x4 to the ceiling to make it more sturdy. I will post pictures soon.

👤If you wanted a better bike hoisting system, you would have to spend a lot of time figuring out what to buy and how to assemble it at a hardware store. The packaging indicates a lesser weight capacity than the 100 lbs listed in the listing. The weight capacity in my packaging is 100 lbs. I am confident that it is more than 100 lbs. This hardware could support it. The installation method is the actual limiting factor on weight capacity. The box has screws that are normally used for installing screws in sheetrock. Anyone who uses those to attach a sheetrock ceiling will have a problem. The result will be weaker if the hardware is screwed directly into the wood after a proper size hole has been pre-drilled. There are suggestions for mounting in other reviews. The instructions don't provide guidance on how to mount it. The installation instructions don't mention the correct route of the rope. There is a hole in the cam lock that should be threaded. It would be difficult to upsize the rope because the hole is barely large. The sheaves and pulley cheeks have gaps. The provided rope can jump out of the sheave grooves if there is a gap. The sheaves are designed so that squeezing the cheeks to reduce the gap results in a lack of lubrication at the axle. The hole in the cam lock does not allow a substitution of a larger rope. It is for this reason that I am giving 4 stars rather than 5, because a person could be misled by the plastic sheetrock anchors and fail to attach to solid wood. The hooks to hang the bike do not have enough curve to hold securely and you probably will need to bend to get a good result. I use a cord under the frame section to secure the hooks to the seat because it doesn't have a structure for them to attach to. There is a chance of conflict with hooks if you have a speedometer or similar device mounted on handle bars. The cleat that is provided to tie off the rope when the bike is lifted is pretty good, but the cam lock is enough to tie off the rope. If you are a belt and suspenders person, you might want to upgrade the cleat. The cleat can be used to get excess rope out of the way. There is a I would buy another one if I had a second bike because this is a good solution at a good price.

7. Dirza Hanger Garage Bicycle Storage

Dirza Hanger Garage Bicycle Storage

No hooks, straps, bars or other equipment is needed. Installation and mounting hardware is included. There is free up floor space. The bike rack is horizontal. It frees up garage floor space by keeping bike off the floor. It's perfect for a garage, home, orshed. Please mount on the wall. The arm is foldable. There is a foldable arm on the bike hanger. It can be folded to save space. The 888-405-7720 You don't have to worry about scratches since the bike hook covers are soft. STURDY: The weight limit for the bike holder is 38 pounds. Most of the bikes are compatible with this bike hanger. Hardware and instruction are easy to use. The bike wall mount rack is easy to install.

Brand: Dirza

👤The out of box experience for these is okay. It will work with lighter bikes. If your bike is under 30 lbs, it will be rock solid when mounted to studs. There is a My wife's bike is a tad heavier than my Giant bike. Hers looks rigid, but I angle down slightly due to being heavier. If you have a heavier bike, I recommend adding washers to the screws to stop it from going through the mount hole. A washer will help. The top half should have two screws if there is a second hold on the top below the first. Most of the weight and stress will be here. The weight of the bike will pull at the top more than the bottom. The single bottom screw is enough for stabilization and the top should have 2 mount points. You can put all screws into a single in-line stud with the Mount holes over the other. There is a It's possible to mount your bikes on the wall side by side or one over the other, and it's also possible to put them on the garage floor. Measure the distance from the base of the mount to the end of the hooks. Measure the distance of your bike's top tube to the outside of the pedal. If you add the two numbers together, you can figure out how far your bike will protrude from the wall. This is to make sure you don't hit it with your car when you pull into the garage. There is a If it's at Mid-height, your pedals or handle bar may hit your side-view mirrors.

👤I bought these to save space in the garage and get the bikes off the floor, but realized that it was difficult to lift the bikes up onto the rack. I am a very small person and that was a challenge I didn't think of. The bike racks are exactly what they are advertised to be. If you are hanging one bike above another, the top one has to be very high. I thought of mounting the bikes on a wall, but it wasn't going to save any room next to the car. I got the rope/pulley kind of bike rack with hooks that go under the seat and the handlebars, instead of these. It is easier for me to pull the rope to lift the bike up from the floor to the ceiling than it is to lift it by hand. I write honest reviews to help others make better decisions because I read reviews myself. I hope my review helped you.

👤Great value! When I first opened the box, I wasn't sure about the strength of it, but after assembling it, I'm convinced it's the best value for money. I don't think there will be a need for a different mount down the road. It folds up when the mount is not being used. The installation was straight forward. The wall needs a 10mm sockets to drive the screws into. You cannot use a drill with a drill bit to screw on a stud. It would have been better if it was a torx screw. Most households should have a 10mm sockets, it is a very minor issue. If you drill a pilot hole, your installation will be much easier. There is a For this price, you get two hanger, not one. If I was looking for another bike accessory, I wouldn't look at other ones.

8. Bike Wall Mount Horizontal Bicycles

Bike Wall Mount Horizontal Bicycles

Keep your garage or indoor space tidy and free up your floor space by storing your bike in a convenient location. Their wall hanging solution to bike storage is great for apartments, homes, garages and sheds. Most bike types have a storage system. The bikes can hold up to 22 kilogram. Not suitable for bikes with wide handlebars (31 inches / 78 cm) or fat bikes. It is safe and secure to store your bike in a horizontal position. The wall mount is made from strong steel. The bike arm locking mechanism uses a reliable gear system. The angle of the wall hanger can be adjusted to keep your bike level. Installation instructions and mounting screws are included. The push button lock system ensures that the frames can be secured, and the cradle arms ensure that all the frames can be accommodated. A secure push button mechanism secures the extendable beam from 8.7 inches up to 12.6 inches. The Armcradles are made from soft TPR rubber material that will not scratch your bike. The frames are protected and the tube shapes are not marked or moved. To prevent front wheel from knocking against your wall, you need a rope that is strong and elastic. If you have a problem with your purchase, they are happy to give you a Refunds or a Replacement. If you have any questions or queries, please get in touch with them and they will be more than happy to help. Only install bike wall hanger on a solid stud, beam, masonry or concrete wall. Unless there is a strong wooden stud behind the wall, do not install on it.

Brand: Pro Bike Tool

👤The rack is nice. It is built out of quality materials and has a lot of flexibility. The mounting points for this rack are a bit odd. They provide you with 3 small screws and masonry wall anchors, when they should have provided a beefier faceplate and 2 lag bolts to mount into a stud. My solution was to take a piece of scrap wood and mount it vertically to a stud using 2 heavy duty lag bolts, then mount the original screws to the wood. The rack gets 5 stars from me.

👤I was concerned my handlebars were too long for your wall mount, so I sent Chris a letter. To make sure they fit, I put a 2x6 board on my wall stud and then put a wall hanger on the board. It allowed plenty of room for the handlebars. There is a I had a problem attaching the hanger to the studs behind the plaster board. There is a one and three-eights inch distance between the wall hanger's two holes. The wall thickness is one and one-half inches. There is no time to get a strong attachment with only a quarter inch overlap. The instructions give a good idea of how to install the hanger on the wall. They warn that the plasterboard won't support the hanger. Very true. The wall stud's width is insufficient. Instructions to attach a 2x6 to a wall stud and then attach a hanger to that board were added by me. There is a The cradles for the bike are red or black, which is a point of favor for the Pro Bike system. The shape of your cradles allows room for the control cables if the bike has them beneath the cross bar. Great feature. There is a Thanks for your help. I hope my experience is useful to others. You have a good product.

👤Highly recommend this bike storage system. Enough about how great it is. I want to know how to install it. You probably do as well. I installed 3 holders. The first thing to do was to find the studs. To double check the exact location of the stud, I used a finishing nail and hammer to find the sides of the stud. I was glad I did because some of the stud finders locations weren't right. There is a You can mount the 3 holes of the brackets into one stud with longer screws than those that come with the kit. Some people have said this works. It didn't seem like it would be stable. I decided to mount a 2x6 across two studs. A 2x4 is not wide enough. I cut the 2x6's 22” long so they fit over the end of each stud. I used lag screws to attach the 2x6's to the studs. I used lag screws on both ends. There is a You will need a impact driver to get the lag screws into the stud. A regular drill won't do it. If you don't have an impact driver, you can always use a sockets wrench. After I tightened the lag screws down, I had to use a sockets for the 5/16 lag screw. I measured the bikes with the holder to make sure there was enough space between them. The measurement resulted in a spacing of 40” from the top of one board to the top of the next board. It was perfect for my bikes. Different spacing is required for your bikes. The wall mounts are perfect. Unlike other systems that are horizontal, these allow you to adjust the arms to fit the different types of cross members as not all bikes are alike. I think they are worth the money. The 2x6x8 was $11 and the 12 lag screws were $9. If you decide to purchase these, I hope this helps.

9. 4 Pack RAD Cycle Products Bicycle

4 Pack RAD Cycle Products Bicycle

A life time warranty on top quality. It was made in Taiwan. The product weight is 1.96 kilograms. 4.35 lbs. The rubber coated hooks are designed to protect your bike from scratches. It's easy to install, you just need to mount to your ceiling joist or rafter. You can have your bicycle hanging in your garage with the minimum of tools. There are four rad bike hoists. Heavy products can be lifted up to 100lb. There is capacity. The bicycle hoist is the one the other are trying to copy. They do not cut corners. You've heard of the original RAD Bike hoist. Indoor ceilings can be up to 12 feet high. You won't know what to do with all the floor space once the bike is out of the way. The safe locking mechanism prevents accidental release. No one wants to find their bike on the floor when they come home.

Brand: Rad Cycle Products

👤There are a couple things about this. I like the idea of this, but there are some flaws. The hooks on the hoist system are just bars. It has a curve but not much to make me feel safe about my bike being in the air. There is a This doesn't fit on a 2x4. You have to angle the screws on the 2x4 to get them to tighten. There is a The screws are next. The screws that come with it are cheap. The screws were stripped during the install. There is a It's a good deal if you rig it yourself. Different screws, bending the hooks, and getting a 2x6 instead of a 2x4 to install this.

👤I tried 4 different bikes and each one had the same program. The bikes fall off the hooks. 1. Hooks aren't hooks. They are a bar bend with a piece of rubber on them that are constantly sliding off. I had to bend the hooks in a way that would allow them to hang on to the handlebars. The seat hooks are only usable on a big bike seat that you can find at walmart. I couldn't secure the seat hook to my Santa Cruz Tallboy or Giant Defy Advance even though I did what I could. I have experience that the standard bike shop quality seat has no place for the hooks to grab. 2. The rope is terrible. Gloves are required to prevent rope burn when raising or lowering the bike. 3. It's not easy to store bikes. If you ride daily like me and my wife, it's hard to raise and lower the bikes.

👤I needed to make more space in my workshop. The value is under 40 for four. There is a The product quality is very good and it took no more than 30 minutes to install the rest after the first one was up. There is a The only concern I have is how long the cord will last. It's a coarse weave. The cut ends weren't properly sealed so they were unwrapped. When raising the bicycles, the cord runs through a small hole in the mechanism, which locks down on the cord. The cord will fail through rubbing and pinching eventually, I guess, because of constant use and always raising to the same level. The bicycles will be stored for a long time without much raising and lowering. There is a If you need storage, go for it.

10. Ultrawall Storage Hanger Garage 300bls

Ultrawall Storage Hanger Garage 300bls

Their first priority is your satisfaction. If you have a problem, just leave a message and they will find a solution that will make you happy. Large capital: The garage wall mount bike rack could hold up to 300 lbs. Bike storage can be tailored to fit your needs by attaching space to the rail. There is safety. The sturdy safety hook design is ideal for your garage storage. The bike storage rack is easy to attach and move around on the rail. Heavy duty mounting hardware. Bikes are not included in the kit for wood stud,drywall,create or brick wall. The material for resilience is powder-coated steel. The sleeves are scratch- resistant. The steel construction has a finish. The material for resilience is powder-coated steel. The sleeves are scratch- resistant. The steel construction has a finish.

Brand: Ultrawall

👤I was able to fit 6 bikes by alternating them. I would recommend installing on the studs. If you like clean walls, you may want to put up a sheet of plywood. The bikes will leave tire marks on the wall.

👤They make things look better. We have a large family with a lot of bikes. They are perfect.

👤This was purchased to hold four bikes in our garage. We have six bikes, but there is no way you can put six of them on this storage rack. Unless you have three bikes for 5-year olds. It is 4' across, and even if you put the bikes on it alternating front and back tires, it would be hard to get six across. I'm sure the manufacturer will say something different. There is a I had to put in some framing to make it work because my location was not on a wall. If I mounted this on the wall, I would recommend putting some tires pre-painted on the wall to protect it against tire marks. To keep the bikes vertical, I'm going to install a couple of 1.5 inch diameter pipes across the railing. There is a The instructions were very bad. My instructions show that this mounting rack is sold with garden tool hooks. There is no mention of how high to mount it, no mention of locating a stud so it can carry the weight of all the bikes you plan on hanging on it, just vague sentences. If you are going to mount this on a wall, I would recommend putting a strip of 1 x 4 across three studs with 3 screws going into the studs. The bike rack can be mounted to the 1-1/8" x 4-1/8" hole. I'm not sure how much stress this puts on the rim of the tire since it is carrying almost all of the weight. It isn't bad for the price.

👤The bike rack is perfect. It comes in two pieces. I put a 24 inch rack in one location and hung 3 bikes there, and the second 24 inch rack is available for 3 more bikes in another area. The mounting screws and plugs are provided in the instructions. The garage I have has a plastic garage tech wall panels which I did not need the plugs for. I installed both pieces in 15 minutes. There is a The rack and steel distribute the weight evenly. If you use a high speed drill with a screwdriver bit, be careful with the screws as they can strip. The hooks are larger than I expected. I hope you are as pleased with the rack as I am.

👤How well the plastic anchors hold up in a Florida garage? I installed it by the instructions. It is 24 hours later. I said this to my wife last night.

👤Did not have enough screws or anchors. The anchors it comes with are for brick walls only. If you want to hang this through a dry wall, wood or anything other than brick, you need to purchase your own anchor and screws. I used a very strong anchor and screw for the drywall that can hold up to 250 lbs per anchor and with 3 kid bike's on one pad, it was too heavy and pulled several of my anchor and screws out. The metal surrounding the screw hole was broken when it pulled my anchor out. I don't recommend this product until they provide customers with the appropriate hardware. It took us an hour to install and another hour to pay for it. I'm not happy.

11. Auwey Hanger Storage Foldable Bicycle

Auwey Hanger Storage Foldable Bicycle

The bike wall mount vertical has a maximum hanging weight up to 66lb and greater clearance from wall to bike to fit a wider variety of bicycles. No assembly is required to save space. You can hang and detach the bike with the fixed hook. It's great for shed corner and garage storage. The wall bike rack has a hook with rubber coating to protect your bicycle from scratches and a locking mechanism to prevent accidental release. Rubber cover to prevent scratches. The arm of the wall mount bicycle hanger is made of soft rubber. The sturdy and durable construction is designed to protect you bike better by holding the bike frame instead of the rim. When you are ready for a ride, the bike rack is the ideal way to store your bike. Lifetime warranty is provided by them and they stand behind their product. If you don't like it, just return and they will give you a full refund.

Brand: Auwey

👤The wall mount works. The mounting instructions and hardware are not up to par. If you are mounting the brick wall on the stud, the screw will not work. Not additional hardware provided to mount on the wall.

👤I needed to organize my garage so I bought some bike rack to hang my bikes on. They are very sturdy and can be folded up to get out of the way when not in use. Shipping was fast. It was easy to install because it comes with all the screws.

👤I put wood screws and washers in a stud in the garage and they work great.

👤It's a great way to hold bikes up and out of the way.

👤The bike hook does a great job. It folds up to save space when not in use. This is what you need if you have a small space for your bike.

👤The bike is hanging from the cement block wall. The price was correct.

👤Very sturdy and easy to hang. What you could want from this? If attaching to a stud, hardware was a bit over the top. I would prefer more hardware over something that isn't enough.

👤It's perfect for our garage. It's out of the way and safe.

Summary

What is the best product for bicycle storage for garage?

Bicycle storage for garage products from Delta Cycle & Home. In this article about bicycle storage for garage you can see why people choose the product. Cyclingdeal and Begona are also good brands to look for when you are finding bicycle storage for garage.

What are the best brands for bicycle storage for garage?

Delta Cycle & Home, Cyclingdeal and Begona are some of the best brands that chosen by people for bicycle storage for garage. Find the detail in this article. Wallmaster, Vibrelli and Ihomepark are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com