Don't need drilling, no damaging walls or ceilings, it's easy to assembly. There is no scratching on the bicycles. Store your bicycle quickly and easily with the included screws and anchors. The bike stand is a space-saving design that allows for portable storage in multiple indoor and outdoor locations. Store according to your needs. The upright bicycle stand can fit almost all 20”-27” bikes with full mudguard when store vertically and horizontally. There are 26”-27” mountain bikes, 650c-700c road bikes, and 20”-24” kids bikes. The display size after installation was 21.65” in length, 20.86” in width, and 44”-47” in height. angular structure andign quality The brackets form a stable triangular structure with ground and the top hook fixes tire. Four non-slip rubber supporting feet will not scratch the floor. The surface of the upright bike rack is coated with high-quality steel and sprayed with excellent powder spraying technology. It can always maintain excellent state, long-term use and stability, even in humid or windy weather. The vertical bike rack is easy to assemble and will keep the room pretty and tidy. The package has an instruction manual that is easy to install in a few minutes. To ensure a great shopping experience, the bike stand has undergone at least 3 times of inspections. If you don't qualify for the bicycle stand rack, they will replace or refund you. To ensure a great shopping experience, the bike stand has undergone at least 3 times of inspections. If you don't qualify for the bicycle stand rack, they will replace or refund you.
👤The stand is easy to assemble. I ran into a problem. The arm wasn't long enough to reach inside the rim of the front wheel with either my mountain bike or my road bike. My road bike is an older steel frame Lemond, and my mountain bike is a Trek Marlin. The catch for the rim was only half way up the front tire, and it wasn't long enough to fit on a road bike with 50mm deep rim. I didn't fit the rack that I had so I really did like it and wanted it to work. It would be a great stand for smaller bikes or road bikes.
👤I got this for my college apartment since our common area is low on space and my bike wasn't helping. I couldn't drill into the wall, so I had to use the ground system. I'm happy to say that it works well. It is perfect for my Vilano Diverse 3.0. It holds it well when I put my bike in. It's easy to take it up and down. There is a The instruction manual is one of my only complaints. It's too small. I had to take a picture of the manual and zoom in on my phone to get a good picture of it. Is it too much to ask for 12 pt?
👤It's easy to put together, stable, and works great in the garage for our bikes. The only way to hang those bikes is either a complicated ceiling/pully system or a front tire wall hanger that orients the bike 90 degrees from the wall and not saving much garage space. The hanger can sit parallel to the wall. The front tire support is great, so you don't need a strap or anything to keep the front tire from flopping around, and the bike feels very secure in the vertical/upright position. It works well with my wife's smaller bike. There is a The directions are printed in a small booklet. All the tools needed were supplied. It took me about 10 minutes to put it together.
👤It's really good for tight spaces that the stand is sturdy. I use it with my road bike. I haven't tried it with a fat tired MTB. There is a The front part of the stand has a red piece of plastic that is like an inverted V shape and I would improve on that. When you roll your wheel onto this piece, it can divert your wheel off to the side. It would be better if they made this into a shape channel that helps guide your wheel into place.
If you have a problem with your purchase, they are happy to give you a Refunds or a Replacement. If you have any questions or queries, please get in touch with them and they will be more than happy to help. Only install bike wall hanger on a solid stud, beam, masonry or concrete wall. Unless there is a strong wooden stud behind the wall, do not install on it. There is space for saving. The bike rack is designed to be hung on the wall to save space. Please mount on the wall. It is easy to fold up when not in use, saving a lot of space in the garage. Anti-scrutch cover. The arm hanger is made of soft rubber to protect against paint damage. STURDY: The bike rack is 3 lbs. The limit is 38 pounds. Large arm holder for bikes. Not for a woman's bike. The solution is perFCt. You can display your bike in any room with a wall mount bike rack.
👤These were bought to hang my bikes. They seem well built and work well. There are two screws on each hanger. You will need a drill and a stud finder. I can't remember what it was.
👤I bought this wall mount to hang my bike out of the way. I was not impressed with the construction, but it worked as advertised and I was happy with it. I decided to purchase another one in order to get my wife's bike out of the way. The second wall mount I received was sagged and leaned forward, making it appear as if the bike was falling and way to heavy for the mount. The issues were resolved quickly after I was contacted by their customer service. The company is enjoyable to work with.
👤I bought my first one a year ago. I ordered another for my Salsa because it worked well and it got crushed by lawn equipment. My only suggestion is that the directions have the right tools for the job.
👤I have a drill set with these but the one sent was too big, reviews said it takes screws, I need a nut driver. I was told I could just screw them into the wall, but I have to get a proper tool. Not good. I put the bike rack up after bringing a nut driver. It's very sturdy and easy to put up.
👤I bought 2 wall mount brackets. After mounting them on the wall, one held up well, the other collapsed under the weight of the bike. The make and model of mountain bike are the same. The mount tube and hooks are bent up from the bike's weight on the metal tab on the mounting brackets. The second hanger does not work. I think quality control is poor.
👤I needed to hang my bike in the garage. This is the way to go. The hook is very well made. The hook lifts up and out of the way when the bike is on the ground. The hook doesn't go against the wall, but it still does what it was made to do and that is to hold your bike. If you use strong molleys and go into a beam you should not have a problem. I used 61lb concrete molleys and no issues at all. I would highly recommend this product.
👤The DIRZA BIKE HANGER works. It keeps the bike in place out of doors, and when I leave Florida, it folds up and saves space. I've been riding bikes for 60 years, but this one is the easiest to install and lift into place. I used a drill to mount the 40 year old STUCCO on the hangar. Worked well.
👤I don't like receiving items that don't match and I rely on the photo. The angle is gentle. This means that the wall brackets are not completely flush to the wall. It seems fine after I attached it. I think the older design is stronger. Can the manufacturer assure consumers that the strength has not been compromised by the design change? I don't like getting something that looks different. It was easy to install, but the strength is questionable at this point.
It is made well and can be seen from the quality of the steel and the fine work. The garage storage rack can hold up to about 450 lbs. The sleeves prevent the tools from sliding. Environmental friendly finish. Heavy duty. It has a greater clearance from wall to bike to fit a wider variety of bicycles. A bike wall hanging on the wall is a convenient storage solution. When not in use, the folding design can be folded on the wall to save space. Attach the bicycle mount to a wall stud in your garage, at work, or in your house and keep your bike handy and ready to ride. All hardware is included to make sure your bike and mount are secure. The solution is for bike storage in home, garage or apartment.
👤You expect a quality product if a company overengineers. The piece of pot metal has a poor choice of screw. If you have the fire power to get through the large drill bits, you can install the fastening inside. It is no longer a convenient option to store the bicycle at a far distance from the wall after the product is installed, but it is still a good option. The thing would hold the bicycle weight and then some. The product was not able to mount the bike on the stand. I would never recommend it to anyone. There is a An upright mounting hook is a better option if the goal is storage. If you want a mechanic stand. There is a I have nowhere to mount my bicycle because my walls are messed up by this design, and there are lots of drywall and sawdust to clean. The thumbs are down.
👤This was in line with expectations. 75% of the audience will not be able to hang this on a dry wall because the bolts aren't intended for stone or brick. I am hesitant to hang my heavy steel off road bicycle on it because I fear the screws I used may fail me, but the lighter composite will be fine. The feature where you can swing the arm upwards so it's flat against the wall is something that I like.
👤They worked well for my bikes. The included hardware may not work for your application since they are concrete/brick anchors. I used the two long cabinet screws from GRK to attach the wall studs. My bikes are 20 lbs. If needed, I would buy again.
👤Someone gave them a 1 star for being so long. It's funny. See the pics for me. 2 bikes are not too far from the pedals. Very strong. Exactly what was promised. There is a change : I am editing my review to say that I did not use the supplied screws. I don't trust the drywall in my house to be strong enough because of the expanding drywall anchor type screws. I put these into the studs with wood screws. I recommend installing into the studs for hanging bikes. The choice to include drywall screws is a bad one by the manufacturer. You can get wood screws for less than a dollar at a hardware store.
👤It comes with anchor and screws, but you will need your own.
It's easy to install, you just need an electric drill and a level to make sure it's lined up in a row for mounting on the wall. The wall collapsed in 16 inches. Installation of paneled wall sheeting must be located to solid structures. All installation hardware is included. The heavy-duty garage bike rack is able to hold up to 66 lbs. It depends on the strength of the wall. The bike hooks are light-weight and durable. All wheels should be fit in the range of 14 to 29" The max rim depth is 50mm. Assembly is not required to install the bike rack. Place studs, tighten screws, and drill hole. You can hang and detach the bike with the wall bike rack hook. The screws and studs are included. Four mounting points and side design make fastening sturdy. The metal hook is covered with rubber which makes it harder to fall on your bike. The holder has a protective plastic coating and is soft. The safety hook has a locking mechanism. Practical and save space. All types of bikes are suitable for the Steady Rack Bike Rack. When you are ready to ride, a garage bike rack ceiling mount is the best way to store your bike. It's great for a home or apartment with limited space. Hanging the bike on the wall is a good idea. Lifetime warranty, including 4PCS bike wall mounts, 4PCS bike rack straps, 16 x screws, and 16 x plastic expansion. They will spare no effort to make you completely satisfied. Lifetime warranty, including 4PCS bike wall mounts, 4PCS bike rack straps, 16 x screws, and 16 x plastic expansion. They will spare no effort to make you completely satisfied.
👤It's easy to set up and comes with straps to hold the wheels and handlebars in place. I have four bikes in my garage. I drilled a pilot hole into the cleat I mounted on the wall, and used the existing screws without a problem, and it stayed put. I used a small wrench to tighten that screw. There is a The bike mout has a hook. The lock is secure and the strap helps keep my bikes in a row. The bicycle's wheels are against the ground. There is a If you use them to hang multiple bikes side by side as me, you will need to leave enough room between them to get a bike to the right. I have the hangers up sixteen inches apart. The kids can put their bikes up. The bike rack gets 5 stars from me.
👤The wall mounts look good. When using a driver to install the screws, the heads snapped off because they were low grade. You can get some decent screws for $4 at a hardware store.
👤The mounts are easy to install and can hold a lot of weight. The hardware they come with is terrible. More: The mounts work very well, as you can see from the attached photos. I use them to store large and small bikes close to the ceiling in the garage, this keeps them out of the way and frees up a lot of space. You should mount them directly into your studs. I wouldn't feel comfortable using the anchors. You should get your own screws. Quality screws can be found at any hardware store. The screws they provide are complete trash. You can twist the screw head to get it into the wall stud. I'm not sure if the screws would be strong enough to hold a bicycle. The included hardware is cheap and could be dangerous.
👤The hooks are five stars and I will buy more, but the supplies screws are criminally negligent. The screws break near the head when screwed into regular 2x studs. I have never seen screws that brittle. The screws are too small for the wall anchor. There is no holding power when you try to attach these without a stud behind them. The supplies anchors need two sizes of screws to work. I can only give a three-star rating for a product which is useful but dangerous through negligent accessories. The straps are very long and they don't make sense. When the hook is at the right height, where the bike puts slight downward pressure through its weight onto the hook, stabilizing the bike by itself, they are not needed.
👤There was no documentation upon hanging the first hanger, two of the four screws snapped in half under the power of a screwdriver, and three of the four screws on the second hanger snapped. This is not the captain America's shield, it is the wood studs that were being used to install it. I got back from the hardware store and reinstalled the first two hangers and the third using screws that are supposed to be used for wood rather than pudding, which is what I think the others screws must be used for. The fourth hanger had to be installed in the wall. I used the anchors. After returning from the hardware store a second time, I was able to hang the fourth one in the wall with the help of the anchors. There is a My five year old will play with the straps until one of the bikes does something bad and has to be grounded, which is the only thing I can think they are for. Save your money. Don't buy it.
The bike fixed hook is an ideal choice. The bike wall racks are a great solution for storing your bikes. If you are looking for a sturdy and efficient bike rack, then this Gootus bicycle wall mount is what you want. They will be happy to help you if you have any questions. The large weight capacity is made of solid steel and can hold 4 bikes and other farm tools, but the weight is better than 200 lbs. The square tube is detachable. You can install two or all of the 3 separated square tubes as you need them for the storage space. There are two combinations that are 30” and 45” long. Adjustable Hooks You could adjust all the hooks side to side with the 4 bicycle hooks, 2 long double-hooks and 2 short double-hooks. The bicycle hooks are rubber coated. The rubber-coated bicycle hooks keep the bicycle safe and stable. Installation is easy. The pieces are clearly stated in the instruction. Installation is easy. The pieces are clearly stated in the instruction.
👤The product was easy to assemble and install. Make sure you use the longest bike to measure the correct height. I grabbed one and measured and installed it because I thought both were the same size. I had to uninstall and reinstall the one I grabbed because it was not the longest.
👤When you get it together, it's sturdy. Lots of assembly is what the box is likely to contain. It should hold 4 bikes, and be sturdy once you get it together. Don't use the mounting screws included, grab yourself some quality lag bolts, and make sure you hit the studs. Don't even think about using anchors. The welds on the bike hooks are the only possible fail point. I wrapped our bike lock cable around all the bikes in case one of them gave out. The cable will keep the bike from bouncing. I paid $13 for my item from the Amazon Warehouse, which was a great price and I am very happy with it.
👤It works, take time to measure, so you don't mount it too high like I did. I can hang a fourth bike, but I don't think there is enough room for 4 bikes. The hook barely gets the wheel through is the biggest complaint I have. It's difficult to get the bike in and out.
👤Only negative. They are not sure if they will ever be available. The order time is 3 weeks. Grr. I need a third to match the room set up. If you can get them, buy them. Pick up some pan head screws.
👤The frame is easy to assemble. The hitch pin design and multiple hole flexibility are nice features. You'll need to be good at playing the game to fit four bikes. The wall mounting screws provided didn't boost my confidence in long term sheer resistance, so it's probably best to upgrade them. Please only mount to wall studs.
👤I need a bike rack for a long time. The extra space in my garage has been made possible by the fact that the bikes are all in one place. It was easy to put together and install.
👤It is strong and sturdy. I gave it 3 stars because I have lighter bike holders. This thing is heavy. If you need a one piece holder, you can buy two or three instead of the two foot iron bar.
👤The unit is pretty stout. The mounting hardware is questionable. There is a The supplied panhead screw is shown in the attached picture. The hole was drilled in the stud. I will get better hardware from the store.
Installation is easy. The pieces are clearly stated in the instruction. Bike rack for garage allows you to keep the bikes off the floor and free up valuable floor space for your garage. The wall bike rack can hold 6 bikes and help you organize your space, it's a thin and sleek design and doesn't take up a lot of space on the wall. The bike rack garage can hold up to 300 lbs and can accommodate 6 bikes. Installation of bike hooks on solid walls is recommended. There is no drywall. The bicycle garage rack has pre-drilled holes and can be installed in a few minutes. There are 6 hooks that can be installed at different heights. The wall mount bike rack is made of high-quality steel. The finish resists chipping. The rubber-coated hooks can help prevent rim or tire damage. The smooth finish of the bike storage hook will last a long time. There is an after-sale service. If you are not satisfied with the bike rack for wall, you can send an email to them and they will give you a 100% satisfaction guarantee. Place the order now! There is an after-sale service. If you are not satisfied with the bike rack for wall, you can send an email to them and they will give you a 100% satisfaction guarantee. Place the order now!
👤The training wheels make it impossible to fit more than 4 bikes. It works well for my needs and the bikes take up less space than they used to. Two thumbs up!
👤The included screws should not be used in the drywall. Get a 65 pound anchor. It will do the job if you install it right.
👤I put it on the cinder block wall in my garage. The holes were drilled, the plate was screwed in, and the hooks were attached to the bikes. 5 stars for quick and easy.
👤It is easy to assemble and mount to the wall.
👤The mount did not hold up on the wall.
The bike storage rack is easy to install and move around on the rail. Heavy duty mounting hardware. The kit for wood stud,drywall,create or brick wall has hardware with it. The wall hanging solution to bike storage is great for apartments, homes, garages and sheds. The storage system is suitable for most bike types. It's also suitable for bikes with their fender. It's not suitable for deep rimmed wheels where the tire and rim are more than 3 inches. Spacing can be adjusted. Heavy duty mental material holds bike vertical rack for home and garage wall mounts, organize gears and save space. Their stylish bike hanger will keep your garage or indoor space tidy and free up your valuable floor space. Hang and store your bike in a vertical position on a secure bike wall, it will allow for convenient storage and removal. The hook is wide and high quality. The design of the hook makes it easy to mount bikes and takes the pressure off the wheels, spokes and rim. The bike can hold up to 88.2 lbs. Bike storage for congested areas allows a bike to be stored in either a center, left or right-angled position, making it a convenient storage solution around parked cars and congested areas. The front wheel should be put in the middle position of the wheel stop and the rear wheel should be put in the left or right position. The front wheel can be locked into place in either the center, left or right positions. 5-minute installation includes easy and detailed step-by-step instructions. There are mounting screws for concrete, masonry or stud walls. 5-minute installation includes easy and detailed step-by-step instructions. There are mounting screws for concrete, masonry or stud walls.
👤It was mounted on the wall. The bike pulled out of the wall as soon as it was hung up. When I hung the bike, the mount twisted up like a pretzel after being re-mounted. Junk made cheap.
👤I bought this for the garage to get my bike out of the way. I will be getting another so we can get our bikes out of the way. It is easy to use. Great for price.
The bike wall mount vertical has a maximum hanging weight up to 66lb and greater clearance from wall to bike to fit a wider variety of bicycles. No assembly is required to save space. You can hang and detach the bike with the fixed hook. It's great for shed corner and garage storage. The wall bike rack has a hook with rubber coating to protect your bicycle from scratches and a locking mechanism to prevent accidental release. Rubber cover to prevent scratches. The arm of the wall mount bicycle hanger is made of soft rubber. The sturdy and durable construction is designed to protect you bike better by holding the bike frame instead of the rim. When you are ready for a ride, the bike rack is the ideal way to store your bike. Lifetime warranty is provided by them and they stand behind their product. If you don't like it, just return and they will give you a full refund.
👤The wall mount works. The mounting instructions and hardware are not up to par. If you are mounting the brick wall on the stud, the screw will not work. Not additional hardware provided to mount on the wall.
👤I needed to organize my garage so I bought some bike rack to hang my bikes on. They are very sturdy and can be folded up to get out of the way when not in use. Shipping was fast. It was easy to install because it comes with all the screws.
👤I put wood screws and washers in a stud in the garage and they work great.
👤It's a great way to hold bikes up and out of the way.
👤The bike hook does a great job. It folds up to save space when not in use. This is what you need if you have a small space for your bike.
👤The bike is hanging from the cement block wall. The price was correct.
👤Very sturdy and easy to hang. What you could want from this? If attaching to a stud, hardware was a bit over the top. I would prefer more hardware over something that isn't enough.
👤It's perfect for our garage. It's out of the way and safe.
Every customer has a premium after-sale service. If you don't like their products, you could get excellent customer support. They will provide top level customer support and stand behind their bike hooks. You will not regret your choice if you just have a try. Their racks are built to last and can hold up to 35 kilograms. Lifting the bike into the rack requires heavy lifting, but it is easy to balance the bike on its rear wheel. Their racks have a 160 degree pivot feature that saves space. Bikes fit snug in the rack resting on the front tire, avoiding the possibility of damaging the frame or rim. The maximum tire width is 24′′ and the recommended wheel diameter is 29′′.
👤The bike rack is great and it was easy to fit two Electra Beach Cruisers on the wall. I put in three racks, two of which were fender versions for our cruiser and one regular for a road bike. The road bike was placed in the middle of a standard 16 inch stud on the end of each rack. It's not easy to store three bikes vertically within 3 feet of wall space, considering the width of the cruiser's handlebars. The road bike rack was staggered down six inches, while the cruiser rack was hung at the same height. There is a The bikes go into the rack with no damage to the cruiser's fender. There is a The only downside is that the instructions tell you to use drill bits that are small. When installing into wood, the pilot hole is too large and the bolt slides out, it's not a good idea. I had to make several holes that had to be patched and hidden because of the error in the instructions. I had to adjust the placement of the racks because of it. It's more annoying than anything, but you should check your drill bit size before you install.
👤We have heavy bikes. The tire width and bike weight can be accommodated in this rack. The quality of these racks is good. The bikes can be turned at an angle once they are in the rack. We put our rack on the side of the garage so that one of our vehicles could be parked next to them. This feature alone is worth the cost. The purchase of the 2-pack was expensive, but I don't regret it. I suppose there are less expensive solutions out there, but this one was easy to install and checked all the boxes.
👤I had taken up too much space in my garage and bought the two pack for two road bikes and the separate fender pack for two cars. Prime shipping was fast and these were shipped via USPS. The packaging was easy to open with a box cutter. I've been following this company since they were a project. When I received their product, I knew what to expect. A lot of thought has been put into everything from the design to the packaging to the website and so on. You need a box cutter, a tape measure, a pencil, a Philips screwdriver, a spirit level, a 13mm sockets, and the instructions call for a 10mm and a 8mm drill bits, but I used a small drill and a small screwdriver. I bought a stud finder from Amazon to make sure I got my holes right. Steady rack has an excellent installation video on their website, but their instructions are very clear and use metric and imperial measurements. The Steadyrack must be mounted into framing studs or masonry in order for the warranty to be valid. Fix the Steadyrack by hand. Installation took about 10 minutes. I'm glad they made fender versions because they worked well with the fender on my cruiser style bikes. This is a high quality item that is worth the price paid and I think it will last many years. It frees up valuable space, holds the bike without damaging it or putting stress on it, and is very easy to load/unload. Excellent customer service and a 100% product backing is what this company is known for.
No hooks, straps, bars or other equipment is needed. Installation and mounting hardware is included. There is free up floor space. The bike rack is horizontal. It frees up garage floor space by keeping bike off the floor. It's perfect for a garage, home, orshed. Please mount on the wall. The arm is foldable. There is a foldable arm on the bike hanger. It can be folded to save space. The 888-405-7720 You don't have to worry about scratches since the bike hook covers are soft. STURDY: The weight limit for the bike holder is 38 pounds. Most of the bikes are compatible with this bike hanger. Hardware and instruction are easy to use. The bike wall mount rack is easy to install.
👤The out of box experience for these is okay. It will work with lighter bikes. If your bike is under 30 lbs, it will be rock solid when mounted to studs. There is a My wife's bike is a tad heavier than my Giant bike. Hers looks rigid, but I angle down slightly due to being heavier. If you have a heavier bike, I recommend adding washers to the screws to stop it from going through the mount hole. A washer will help. The top half should have two screws if there is a second hold on the top below the first. Most of the weight and stress will be here. The weight of the bike will pull at the top more than the bottom. The single bottom screw is enough for stabilization and the top should have 2 mount points. You can put all screws into a single in-line stud with the Mount holes over the other. There is a It's possible to mount your bikes on the wall side by side or one over the other, and it's also possible to put them on the garage floor. Measure the distance from the base of the mount to the end of the hooks. Measure the distance of your bike's top tube to the outside of the pedal. If you add the two numbers together, you can figure out how far your bike will protrude from the wall. This is to make sure you don't hit it with your car when you pull into the garage. There is a If it's at Mid-height, your pedals or handle bar may hit your side-view mirrors.
👤I bought these to save space in the garage and get the bikes off the floor, but realized that it was difficult to lift the bikes up onto the rack. I am a very small person and that was a challenge I didn't think of. The bike racks are exactly what they are advertised to be. If you are hanging one bike above another, the top one has to be very high. I thought of mounting the bikes on a wall, but it wasn't going to save any room next to the car. I got the rope/pulley kind of bike rack with hooks that go under the seat and the handlebars, instead of these. It is easier for me to pull the rope to lift the bike up from the floor to the ceiling than it is to lift it by hand. I write honest reviews to help others make better decisions because I read reviews myself. I hope my review helped you.
👤Great value! When I first opened the box, I wasn't sure about the strength of it, but after assembling it, I'm convinced it's the best value for money. I don't think there will be a need for a different mount down the road. It folds up when the mount is not being used. The installation was straight forward. The wall needs a 10mm sockets to drive the screws into. You cannot use a drill with a drill bit to screw on a stud. It would have been better if it was a torx screw. Most households should have a 10mm sockets, it is a very minor issue. If you drill a pilot hole, your installation will be much easier. There is a For this price, you get two hanger, not one. If I was looking for another bike accessory, I wouldn't look at other ones.
The quantity is 2 pieces and the Rim is 3.3 inch. Koova Bike Rack is a sturdy, easy space-saving storage system for bikes and helmets. It's simple to mount on a garage or shed wall. The hooks hold the bicycle until you are ready to ride. Hardware needed to mount in minutes is included. The bikes should be resting on the hooks. Up to two helmets are out of the way when storing your bikes, so it's a good idea to store them neatly. The steel component is cut and powder coated. Their innovative design supports the bike's weight while rubber encased hook cradles are not damaging the rim, tires or spokes. Water bottles, tubes, and other items are on a utility shelf. All bikes are compatible. You can hold your road, hybrid bikes and beach cruiser in one spot. Ample space between bikes allows for quick dismount. Fat tires? There are 3”+ sized hooks available. Koova's Bike Storage Racks are guaranteed to last. They offer a lifetime satisfaction guarantee. They will repair, replace or refund your money if you are not happy with a product.
👤I have always stored my bikes in the garage. I started talking to the owners of the bike shops and looking at the line. The Koova system is the best of the best according to the other reviewers. The bike storage rack has a top gun. To me, the most important thing is the wide of the tire and the properly-angled hangers. The J hook design used in the systems I had seen looked less sturdy, complicated or worse, and it made mounting a two person operation difficult. The helmet hooks are an added bonus. Everything can be stored in a single location. I bought the six bike rack. Three children were riding their bikes at the time of the review. You might see tire marks on the wall now that bikes are mounted. Not a dealbreaker. I'm sure I can come up with a solution. I had a question about the ideal height of the hanger channel above the floor to accommodate my cruiser bike. Within a few minutes of sending an email on a Friday afternoon in July, I got a nice reply from the founder, Mr. M. Richards. I know I made the right choice because of customer satisfaction.
👤It's very easy to install and hold 4 bikes. I don't know how you can get 6 bikes on this rack. The extra brackets were used to hold tie downs. It's easy to move the bike off the rack.
👤It's the best on the market. This product is worth every dollar. I couldn't get 3 bikes to fit, so I was confused. The CEO reached out to me after I wrote a review and explained that the middle bike and 2 outside bikes are supposed to be handle bars up. You can maximize the space by doing that. It's rare to have a CEO. It is advisable to send a gift for the confusion as well as go to this level of customer service. I left a review for the Koova Garden Wall Mount. Another great product from this company. I bought a second one because I liked it so much. In the picture, I only have a small portion of the sets up. I put 3 bars together in each set. The 4th bar is on a different wall. This is by far the best unit out there. Is easy to mount and durable. I told you that I have 30 items on my wall. It is not even 2 full sets. It looks organized and not cluttered. A good one.
👤This was the easiest bike wall mount I have ever installed. It can fit 6 bikes top to bottom. We have a mountain and road and it is not an issue. The only thing that happened during installation was the head of the mounting screws being twisted off. It needs to find another one and mount it lower. An extra in the package would be nice.
👤This is an excellent bike rack. If I had ordered the 6 bike mount, it would have been sent as a set of 2 mounts that are about 32ish inches long. If you don't have the space on a single wall, you can mount in 2 different locations. There is a It came with all the necessary hardware. I put it into concrete. I used the same screws as the included lag bolts. It worked fine and did not cause any issues with the bike mounting hardware. It was very easy to install. I received a package in the mail that contained additional screws because there was a report of lag bolts sheering, which seems like a small company. I would buy again.
Bicycle rack for garage wall products from Begona. In this article about bicycle rack for garage wall you can see why people choose the product. Dirza and Homee are also good brands to look for when you are finding bicycle rack for garage wall.
Begona, Dirza and Homee are some of the best brands that chosen by people for bicycle rack for garage wall. Find the detail in this article. Smallrt, Action Club and Walmann are also brands that their products are worth to check.