Best Bicycle Quill Stem Riser

Stem 14 Aug 2022 10+ Comments Open

1. SENQI 22 2×25 4mm Electroplating Gooseneck 80×220×240

SENQI 22 2%C3%9725 4mm Electroplating Gooseneck 80%C3%97220%C3%97240

The stem is 25.4mm in diameter. The handlebar is 25.1 inches in diameter. The fork Clamp has a diameter of 22.2 MM.

Brand: Senqi

👤I rebuild bikes that are fun to ride. I was looking for a riser stem that was vintage. There is a The stem looks good. It was shiny and smooth. You may notice the cheapness if you spend more than 5 seconds. It is quite heavy. The metal is finished and shiny, which is what you would expect from a 20 buck part. The head cap screw is not low enough to be set in the counterbore. Even when tightened, it sticks out. Unless the manufacturer corrects the design oversight, it will show up in every copy. The counterbore is not centered on the tapped hole. I don't know if that is a random defect or a tooling setup problem. It works, but it looks ugly. I noticed that the travel was not smooth when I ran the screw up and down. The metal fragments were stuck to the tip of the screw. The manufacturer didn't clean the chips well after the operation. Again, doesn't hurt anything, but it hurts for quality. There is a You get what you pay for at the end of the day. There are small defects on the 20 buck quill stem.

👤I bought this bike 3 years ago so that I could get back into bicycling after 30 years of motorized two-wheeling adventures. I was unable to find one that was longer than 180mm, but it did make the target. The one that hit the bulls-eye did not go past the safety margin line. I'm glad I found it.

👤I can't speak to the function of the bike stem because it was the wrong one for my bike. It was moved around the counter for a few days and didn't show any wear or scratches. It was high quality and sturdy. I was disappointed that I didn't pay more attention to the item I ordered because it seemed like a quality item and I wish it would have fit right.

👤I bought the silver quill stem to upgrade my Schwinn road bike from drop bars to upright handlebars. The stem did the trick. I bought the longest one, but it doesn't seem to be available at the moment. There were no complaints. I bought a second stem to convert the same era vintage Schwinn for my son who doesn't like drop bars.

👤Beautifully finished and with a longer quill, but not so long as a nitto technomic. I had to use a pry bar to open the clamp to get over the curves of the drop handle bar. It would be 5 stars if it wasn't 5 stars.

2. Sunlite Piston 2 Bolt Clamp Silver

Sunlite Piston 2 Bolt Clamp Silver

The bike can be upgraded. Downhill, Chongshan, climbing, are very comfortable. The stem is 250mm x 22.2mm. x 40mm The forged alloy body is made of material.

Brand: Sunlite

👤I wanted a hybrid bike to jump on for family rides, without having to use my road bike or mtb bike. It wasn't enjoyable to just cruise around on a road bike. I was going to either spend $500 on a decent hybrid or find a way to modify the beater. For $16 and another $10 you can get a longer front brake cable. It is really nice to ride and it looks rediculous. The stem is not twitchy when out of the saddle and there is no flex in it. I'm very happy with the stem. I did this because I wanted a bike.

👤It worked perfectly for a month and 700 miles. It fit an inexpensive mountain bike with a standard cruiser fork, headset, and handlebar. It doesn't need to be retightened. Grease was added to the bolts. It made a new bike feel comfortable. The long stem helps tall riders sit upright. The product photo made the stem clamp look thin, but it completely covered the handlebars with only a small amount of lines visible on either side. The product is appealing and has a great value.

👤This is on a stout stem. It was easy to cut down. This is for an older 90s hybrid. It handles it with some force. If you like handling your whip quickly, this is it. It is very long. I had to find another shorter wedge bolt after cutting mine down.

👤A steel stem with a cast aluminum handlebars. I was expecting all aluminum, but it was much heavier than I thought.

👤I have been using this for two months and have not had any problems.

👤I needed to raise my handlebars for a more upright riding position. I installed it backwards. It's nice to have a two bolt setup for the bars. The weight is not nice. This thing is very heavy. It's not something that one would want to install on a light weight bicycle.

👤The Sunlite TCO will get you into a comfortable position. There is a It's a position that lets you keep your eyes up. It has been reliable for me, and I have traveled thousands of winter miles in Boston.

👤I wanted a tall stem. It works well. It's heavy, but it's used for a specific purpose -- I adapted an old road bike to a flat bar fast bike and wanted to have an upright riding position. It seems well made.

3. Extender Handlebar Aluminium Mountain Extended

Extender Handlebar Aluminium Mountain Extended

The instructions are given. The wrench should be used in the direction that the front wheel points for installing the pedal. Strong material: forged aluminum alloy material, solid and firm handlebar extender, durable for more safety when used. The stem riser can adjust the gasket to fit your height, which will reduce the pressure of the waist and raise you to your comfortable position. Simply connect up the original bicycle fork stem. Most of the Met bikes have a handlebar riser. Handling more flexible, light weight, much easier to force when climbing, is comfortable, convenient bike fork extender. Most of the Met bikes are compatible with work on mountain or road bikes with thread less Steering tube. The bike fork extender is convenient.

Brand: Emoly

👤The product has a number of design flaws that make it very unsafe. It is unsafe because it doesn't allow it to be tightened enough to keep the fork from rotating. If you have more than 15 pounds of pressure and your bars and front wheel are not aligned, you can turn the bars without the wheel moving. There is a The shape of the bolt threads in the threaded end is the worst flaw. It means that one side has more threads to hold the bolt than the other. If it was better material than a cheaper one, it would be sufficient when tightened. It is shaped that way and that makes it hard to use a stop nut behind the integrated threads. The bolt was bent by the use of an angle washer and stop nut. There is a This is the product for broken bones.

👤I reviewed many of the STEM Extenders because the handle bars were too low and I wanted to ride my mountain bike in a more natural position. The instructions were clear. The tools were provided. Good construction. I enjoy riding my bike and feel accomplished. Best to everyone.

👤After taking off a few years, we are getting back into biking. The husband put a lot of money into his ebike. I wanted to keep my Diamondback. I found my hands and neck were not comfortable at the angles that have been an issue before. The problem was solved by this extender. It looks great on my black bike with red accents, and it gives me a solid gripping area when I load it onto the rack. It's easy to install. Very pleased!

👤The design of the stem extension is solid. The product is pretty nice and the anodizing process makes it feel high quality, even though I was skeptical at first. Highly recommended.

👤You pop this on top of the steerer. Just remove 3 bolts. Next, screw them back in place. You can't stop smiling when you ride a bike that fits all of a sudden. Wake up dude, wake up now! Welcome back to reality! Good morning America! It was a dream. You can only turn the steering wheel 8 degrees to the right and 8 degrees to the left in real life. Why amigo? The steering wheel range of motion is limited by the stretched brake cables. If you already have long cables and housings, you are one lucky guy. Don't forget to contact me if you win a lot, I will get 10% of your winnings. Remember, it was my idea?

👤There was a gap between the bike steering stem and the extender after it was installed. The inside dimensions of the extender do not allow it to seat properly. The problem could be solved by changing the inside dimensions of the extender to match the dimensions of the bike stem, or by using a ring to close the gap between the extender and the handlebars.

👤Allen stripped the threads when they were tightened.

4. FOMTOR Riser Handlebar Extender Mountain

FOMTOR Riser Handlebar Extender Mountain

A universal short handle bar stem is suitable for most bikes. The maximum height extension is 70mm. There are 4 spacers, 1 x 10mm and 3 x 5mm. The height can be increased up to 70mm. Simply connect the original front fork stem to the new one. Light weight. It is made of high-strength T6 aluminum alloy. Handling more flexible, light weight, easier to force is comfortable. It's suitable for 1-1/8" 28.6mm Fork Mountain Bike, Road bike, Track bike, Folding bike, MTB BMX...

Brand: Fomtor

👤The stem riser extender worked well. Before this extender, I could have raised my seat to the proper height for my legs, or I could have put my seat too low for my legs, with good upper body posture. The performance of the extender is good. The bolts are smaller than the original neck bolts. I gave the extender 5 stars because they are holding. I will look for an extension with beefier bolts if they fail. Installation took longer than expected, but not because of the product. The nut in my stem was a little crooked, but it wasn't noticeable on the short bolt. I wonder if those people had a crooked stem nut assembly like me, because I read a number of reviews that the long bolt was bent. The graphic I attached shows what I found. I lightly tapped the head of the bolt with my finger to make sure the stem nut was straight. The stem bolt on my bike is held in place by 2 star shaped pieces of steel. It was not very precise, but easily straightened. The long bolt worked perfectly when the nut was straightened.

👤The stock steer tube on the 2012 Trek 3500 was too low for the current rider, and the handlebars were too low for the original 2012 Trek 3500. Those in need of an elevated handlebar need a stem extender. There is a The FOMTOR stem extender is an excellent quality aftermarket bike doodad. It has nearly four inches of vertical position. It includes a long titanium bolt to reach the distant star nut, six aluminum spacer rings, and a matching cap. There is a The FOMTOR stem extender was perfect for the existing steer tube. The titanium stem bolt is stout enough to hold the entire headset in place, and appears to resist dynamic loads and stresses under normal use. Black powder coat finish is what the stem extender, cap, and spacer rings are made of. There is a It's annnnnd... I bought the last one on Amazon. I need two more.

👤I used these for my bike. It made a huge difference in my riding position. The height to the bikes handle bars was increased by the spacers. I liked that it was all plain black and not colored. The end was very clean.

👤The bent bolt makes it hard to install with the new cap. The stock cap is not centered because it was not used without the recess. The bolt would be 5 stars if it wasn't bent.

👤It was my fault that I didn't double check the measurements for the bike I am fixing up. I won't be returning it because I am hopeful it will fit on another family member's bike. I was sad it didn't fit on my body, but it looks like it's very high quality. Will update this review if it works for the other bike.

👤The extender tightens down when it connects to my fork tube. I had the right amount of spacers and the extender fit my new stem perfectly. I am happy with my purchase and would purchase again.

5. CXWXC Adjustable Stem 31 8mm Degree

CXWXC Adjustable Stem 31 8mm Degree

The safety is certified by the EN. Can't get comfortable on your bike? Did you try too many bike stems? For touring where you spend a lot of time in the saddle, this is a useful way of adjusting your handlebars height and reach. The best bet to get comfortable is their stem. Only fit for Handlebar diameter 31.8mm (1-1/4''), front fork stem diameter 28.6mm (1-1/8") and is available in a range of lengths. Before purchasing, please confirm your size. The material is. The 3D forged alloy construction of the MTB stem gives it strength and control. The stem is very durable with an angle of 70. It's easy to connect up the original fork stem. The four bolt bar is in position. It's suitable for most bikes. Their bike stems can be used for a wide variety of bikes. It's ideal for people who take off road biking very seriously.

Brand: Cxwxc

👤This is a nice stem. It's tight and easy to adjust. It has bigger 5mm bolts than the smaller 4mm bolts that are used. The cheap Chinese risers I had had so much slop in it, the handle bars were rocking back and forth. I couldn't get it out. This one looks more expensive than it is. The rise degree indicator is accurate. The quality of some of the "name brand" risers is probably the same. All of it was made in China.

👤I put this on my Fatboy to raise my handlebars. There is a The unit looks amazing, matches the bike's finish very well and has a very solid feel to it. I'm a new bike maintenance person, but I recommend that the handlebars be screwed on during the installation process. The screw holes didn't line up exactly when I attached the handlebars, because I removed that immediately. Less than half a millimeter off. I loosened the angle adjustment screw and took some plastic wedges between the sides to allow me to secure it with screws again. I like how it turned out. If I want to go back to the trails, it is totally changeable.

👤The hassle of changing everything over on new handlebars was thrown into the mix when these brought my stock handlebars up 4 inches. Everything was kept tight. The length is 5 1/2 ". The stock stem was 1 1/2 inches.

👤The handlebars had to come up to relieve the pressure on my hands. The riser helped a lot. No issues so far. I put butterfly bars on this bike. What a change! The bars and riser worked well together. The best bike mod I have ever done. This riser gave me a lot of options and angles to work with.

👤After 3 tries, this one actually fits real mountain bike bars. The only downside is that you will need an extra spacer to make the neck fit the stem and be tightened from the top properly. I had one laying on the floor. If you plan on using this neck, I would recommend buying some. Thank you.

👤It was easy to install on the gray Vista bike. I wish I didn't have to return the bike because of the poor transportation. The steam would make the bike look better and more comfortable.

👤I used this to increase the height of my handlebars. It worked out great. It is easy to assemble. You should know the diameter of the handle bars. Originally purchased for my wife. She had 1” in diameter.

6. Origin8 Quill Adapter 22 2 Black

Origin8 Quill Adapter 22 2 Black

A bolt with aluminum. A threaded setup is converted to threadless. Stem height can be raised by one-tenth of an inch.

Brand: Origin8

👤I don't have a lot to add to the other reviews, other than I wanted to add a note to prospective buyers about the height adjustment capabilities of the adapter, if you want to have your handlebars raised up a bit. You can see what I'm talking about in the photo I uploaded. There is a There is a height adjustment in the description. This means that you can slide the accessory up from the top of the head tube, and still have enough for a secure fit. If you don't want your handlebars to be low and you want the height to be added, push the adapter all the way down. There is a There isn't a "do not raise above this line" type of marker on the adapter, but there are some short vertical marks that I thought were the max-height marker. There is a I only got 0.75" of added height because my stem is a bit taller than many others. You can see it in my photo. You can get about 0.75" - 1.0" of height adjustment if you use the height of your stem clamp. If you need more height, you'll need a stem with a higher angle. I'll get a black stem headset spacers to slide over the silver part of the accessory so it looks better. There is a I'm docking my review to 4 stars because of this. It would have been nice to have another inch of height. The product is easy to use and install and looks to be well made. I installed mine on a mountain bike. I got the small to large size. You can see the "top review" from PRS4 for more explanation of the different sizes.

👤It works well, does what it says, and looks good. This little guy can help you update your stem and handlebars. Antiseize or grease should be used during the installation to keep the rust at bay.

👤I was a bit leery of the quill accessory, which was part of the upgrade to the old road racing bike. The new bars needed a stem that was modern, and the old bike needed a quill to fit it. The new setup feels more rigid, solid and responsive than the old one, and I am pleasantly surprised by it. The bars are nicer to my hand.

👤Just as advertised. I got the 28.6 to 28.6 size and thought it was an adapting sleeve. I can't tell from the description if the picture changes to show the sleeve or not. I didn't know that when I swapped the pictures. I can always use the sleeve on another bike if I need it. I recommend this on any threaded bike since it's so easy to swap the old style stems for the new style ones without the need to disassemble the brakes.

7. Origin8 Pro Fit ATB Stem

Origin8 Pro Fit ATB Stem

A forged aluminum construction. The fork is 1 inch in diameter and 25d angle. The stem is 180mm long. Modern OS bars are great on older frames. The safety is certified by the EN.

Brand: Origin8

👤I can't say enough about Origin 8 products. They are not the top of the line, but they offer something for everyone at a very reasonable price, and I've never had a failure between brakes, rear racks, or anything I've tried on updated conversions. This stem was exactly what I was looking for to convert my old Specialized Stumpy/Judy Shock to the current handlebars, and made it easy to switch between different styles of bars until I found the rise I liked. I put a small plastic sleeve around the top of it to make the female/male fit a little tighter, I also used a white plastic piece that I modified to fit with a knife. Would buy again, and probably will again.

👤This is the most cost effective upgrade you can do on an older bike for casual riders. The construction of this stem gives me confidence. This will hold up for a while for casual riders who ride on a curb or dirt path. It's a great way to upgrade and use more current gear on an older bike. The joy of riding is restored for under thirty bucks.

👤It's difficult to find a 1" quill stem with a decent rise and aremovable face-plate, especially with a 31.8mm clamp for the new road or mtn bars. I like the 4-bolts on this stem. The bolts on this stem are cheap, but I never feel safe on them. They are painted black. The wedge bolt is heavy-steel. This is a good stiff stem and I'm happy with it.

👤I bought a Huffy bike and am fixing it, but I hated the handle bars. I bought a new set. I couldn't use the old neck because the new set had a 31.8mm tube. Origin 8 to the rescue. All of the questions about whether it will fit a cheapo bike are answered here. This is what you want if you want to modify your Huffy. There are photos of the FWI.

👤I have an inexpensive mtb that I am going to use to buy a road bike. The stock bar setup was too narrow. The stem I bought was needed to fit a set of bars. For extra height, I chose a max of 112mm. My cheapo is starting to feel like a legit mtb after this solution. The fit and finish is decent.

👤These fit my bikes perfectly. I recommend them. My son-in-law's bike has one pair on it and my bike has the other. They are built to last. I believe they will last a long time.

8. Wake Mountain Handlebar Bicycle Aluminum

Wake Mountain Handlebar Bicycle Aluminum

It's suitable for most road bike, mountain bike, track bike, BMX, etc. The handlebar diameter is 25.4mm (1"), the Stereer Tube diameter is 28.6mm (1-1/8"), and the length is 32mm. Simply connect the original fork stem to the new one. The four bolt bar is in position. It is made of high-strength T6 aluminum alloy. A universal short handle bar stem is suitable for most bikes.

Brand: Wake

👤It hasn't broken off, so that's a great start to the review. I can see how these don't give you much wiggle room when it comes to over tightening them. If you try to feel it out, be careful if you ate spinach before. They use soft metal. It is mounted to a 29er hardtail that is used weekly and it has the ability to secure the handlebars from moving safely. I am gaining a full piece of mind while riding it. Some people said it fell apart worse than Charlie. I'm alive to give this update because it hasn't snapped off yet.

👤I used to do a lot of it. There is a The quality of this is exactly what you would expect. There is an error in the program, one of the machines has some worn items, the work piece wasn't fixtured correctly, or something else happened because there are two nice "flying-V" cuts on both sides of the stem. The end mill grazed the sides in error and it looks hilarious. I'm not going to swap out for something else. It seems to be a solid unit. The 60mm version is as heavy as my old 90mm stem with bolts. Not much has been done to reduce weight. I wouldn't expect it to be very well designed. This is probably not going to break. Unless I huck this gravel bike over a 50 ft gap. There is a The screws are the same quality as other low end screws. I can't complain much. The pockets the heads and washers are supposed to sit in are not made properly. Some of the heads are more proud than others. I'm pretty sure that the clamping forces are good enough, it just looks funny. I wish the threaded holes were tighter, but it works. Is it actually anodizing? I'm afraid to ask at this point. It has a different fit and finish than the high end stuff. There is a It got my handlebars where they needed to be, and it probably won't break, so good, right?

👤I've put these on two of my bikes. It doesn't get any better for the price. It's inexpensive and doesn't stand out, which is a good thing. There is no benefit to higher priced stems. Unless you need to save a couple ounces, don't waste money on a carbon stem and just use one like this. I bought these because it's short. It will make the bike more responsive when turning. There is a If I need another short stem, I will buy them again.

9. Satori Bicycle Tool Less Adjustable Extension

Satori Bicycle Tool Less Adjustable Extension

The handlebar has a diameter of 25.4mm. COMPATIBILITY: Only the 1-1/8" / 28.6mm THREADED fork steerer can be compatible with this stem. Make sure to double check the fork size and type. It'sATURE: Simply press and open the safety button, then pivot the stem to any angle between 0 and 80 degree to adjust the height and reach of your handlebars. Serrated and precisely made handlebars for more powerful clamping. It's difficult to find a stem that fits a 1-1/8" threaded fork nowadays, and this specific stem will do the job. The material is made from one-piece forged alloy. It is easy to wipe off and clean with matt black finishing. There are some things that areSPECS. The stem length is 120mm. The handlebar's size is 31.8mm. The angle is 0o to 80o. The height is 180mm. The insert is 65mm. The weight is 606g. The material is forged alloy. You can order now and pay free. They can provide a 2 year warranty on their product. It was made in Taiwan.

Brand: Satori

👤There is a hole in the rotating hub that needs to be bored in order to pass an Allen key down and access the long bolt that tightens the stem. The hole in the stem was too small. I couldn't use the key wrench to tighten the stem. The hole I drilled out was an unnecessary modification.

👤The handlebars are great, but it took me a while to figure out the basic workings of the unit. It will be amazing when I dial it in. Does anyone know how to put the handlebars on? Is it better to tighten them down once everything else is shut down?

10. UPANBIKE 22 2mm25 4mm Aluminum Gooseneck Length

UPANBIKE 22 2mm25 4mm Aluminum Gooseneck Length

It's for road bike, mountain bike, and other bike. The material is aluminum alloy. The handlebar is 25.4mm in diameter. The fork tube has a diameter of 22.2mm. The stem length is 40mm or 80mm. There are millimetres. The stem rise angle is 30.

Brand: Upanbike

👤The bike I bought was too large for me. The handlebars were brought down to get the right fit. If you want to mount the handlebars, you will have to remove the levers on the other side. It was very easy to install.

👤It's easy to install. When the stem is raised to about a half inch lower than the max, there is no flex. The upper position. There was no side slip. Our new Schwinn trike is perfect. There is a Ps. I have been working on bikes for 50 years. I usually don't like these kind of stems because of the flex, but the price on this one is right and the bike fit is perfect. Great deal.

👤I had to raise my handlebars to take some of the stress off my shoulders. The bike stem worked well. It was easy to install, and seems like it was good quality.

👤The stems put you on the bike so you can enjoy your ride without neck and back problems. It makes your ride more efficient.

👤The stem was too small for me. The finish and design are very nice.

👤The stem's wedge wouldn't grip the inner steerer tube, which allowed the handlebars and front tire to be moved in opposite directions, so I wouldn't give it a 4 star rating. The old wedge worked after I replaced it with a new one. The rest of the stem was advertised and works.

👤My kid's bike has more life because the handlebars can now be raised, so it will fit him for a few years.

👤It isn't a nitto. It is also not $70. It does its job perfectly and doesn't look bad.

👤I bought this because I wanted to get more height in my handlebars and move it closer to the seat. I question the quality. I think I might have gotten a returned item as the finish had some scratches near the mount, but it's not important for me as my bike is vintage and scratched. The plastic cap does not fit, I had to use the one that came with the bike, the shaft wedge function is questionable, and the handlebars came off center while riding on bumpy ground. I may have to use the stock stem's wedge to get around it. I found that the Torque on the handlebars needs to be tighter than I thought it was, and I am afraid that it might break, so I needquing specs to help. If it breaks, I will tighten it and ask for a return. For the price, and re-using of existing parts, it is okay.

11. TRIWONDER Aluminum Extender Extension Mountain

TRIWONDER Aluminum Extender Extension Mountain

The material is 6061 aluminum with a polished finish. The base diameter is 1 1/8” (28.6mm). The total length of the steerer tube is 150mm. The height of your handlebars should be raised. It is easy to convert a threaded quill setup to threadless. It's perfect for most bikes. The quill riser extender can be used on most bikes with a threadless steerer.

Brand: Triwonder

👤Needed to install a pro scooter stem on a 49cc scooter.

👤This is what you need to put a thread-less stem on a threaded fork. Plug and play works great.

👤The ottimo is called qualita'-prezzo. There is a Per modifica l'attacco manubrio per piantoni da 25,4mm.

👤Para poner una potencia, el manillar en uncuadro antiguo.va.

👤C'est facile monter.

👤Decid probar el extensor de vstago de manillar para bicicleta de montaa. Tenia para desmontar la horquilla, pero se pueda introducir el adaptador. No le hizo demasiada gracia. Quiz sea porque est enfocado. Ahora, lo bueno, ha sido para sutituir el manillar de una bicicleta. The original de la bicicleta istituir el vstago. Potencia y manillar, con los, ms a gusto. The tubo is 22.2mm in diameter. Con lo. The encaje is perfect. There is a En resumen, el vstago. No lo aconsejara, hay otros modelos that son ms sencillos de colocar. Vstago sustituto para modernizar una bicicleta ms antigua is una excelente opcin. La calidad del vstago es una. Mucho ms caras hay opciones. Tengo aprovechar las vacaciones para actualizar la bicicleta.

Summary

What is the best product for bicycle quill stem riser?

Bicycle quill stem riser products from Senqi. In this article about bicycle quill stem riser you can see why people choose the product. Sunlite and Emoly are also good brands to look for when you are finding bicycle quill stem riser.

What are the best brands for bicycle quill stem riser?

Senqi, Sunlite and Emoly are some of the best brands that chosen by people for bicycle quill stem riser. Find the detail in this article. Fomtor, Cxwxc and Origin8 are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com