Best Bicycle Quill Stem Extender

Stem 25 Jun 2022 10+ Comments Open

1. Sunlite Cromo Quill Extender 25 4mm

Sunlite Cromo Quill Extender 25 4mm

The fork Clamp has a diameter of 22.2 MM. Rise for the stems. Raises Stem another 8 inches.

Brand: Sunlite

👤The extension bar was a good fix for my stem problem. The vender did not give any useful information. The Flared section of the tube begins at the center. Tubes are above the headset lock nut. 2. The length of the extension tube can be found from the top of the inner cap screw to the top of the extension tube. 3. If using a L-shaped tool, the cap screw requires a 6mm Allen tool. The Neiko Log Hex Bit Socket Set, Metric 3 - 10mm, is sold by Amazon. The tool is 4 inches long from the tip of the Allen head to the back of the sockets. There is only enough sockets to fit a drive ratchet. I don't think a ball-end Allen tool will work due to the shallowness of the cap screw. The drive extension bits should work for shorter sockets. 4. A specific amount of Torque was not given. You will have to research what is appropriate for your situation, but my research suggested 20 to 30Newton-meter. I was not able to Torque all the way to 170 inch-pounds because I did not have a strap wrench. The bolt is tightened in short, sudden jerks rather than easy pulls. The outer shaft will still spin, but the bolt will tighten. This won't happen with easy pulls as the bolt and unit spin in unison as it tightens. I was able to tighten the bolt so that the extension wouldn't spin and the wheel wouldn't twist. 5. One should change to longer cables and housings to accommodate the new stem. 6. Hopefully these notes will help fellow cyclists.

👤The TREK Verve 3 bicycle has a quill extender on it. It fit well and seemed to be perfect. I tightened the screw, thinking it was necessary. I mounted the bike, rode 100 feet turned a corner and fell over as my handlebars loosened. I fell on the grass and was indignity. I tightened the screw on the quill extender on my bicycle and was afraid I might tear out the threads. I fell over on my concrete driveway when I rode in a circle with the handlebars turned enough to maintain the rough outline of a circle. I had only minor injuries. The handlebars had a rotation. I removed the extender because I was done. The handlebars worked perfectly again but were not as high as I would have liked. I'm pretty sure that this extender will work on a lot of bikes. It didn't work for me. Before you use this extender, be sure to test it thoroughly. Losing handlebar control could be very dangerous. I fell in ways that did not cause much injury. Imagine if the handlebars came loose while riding in a busy city street.

2. CXWXC Adjustable Stem 31 8mm Degree

CXWXC Adjustable Stem 31 8mm Degree

The safety is certified by the EN. Can't get comfortable on your bike? Did you try too many bike stems? For touring where you spend a lot of time in the saddle, this is a useful way of adjusting your handlebars height and reach. The best bet to get comfortable is their stem. Only fit for Handlebar diameter 31.8mm (1-1/4''), front fork stem diameter 28.6mm (1-1/8") and is available in a range of lengths. Before purchasing, please confirm your size. The material is. The 3D forged alloy construction of the MTB stem gives it strength and control. The stem is very durable with an angle of 70. It's easy to connect up the original fork stem. The four bolt bar is in position. It's suitable for most bikes. Their bike stems can be used for a wide variety of bikes. It's ideal for people who take off road biking very seriously.

Brand: Cxwxc

👤This is a nice stem. It's tight and easy to adjust. It has bigger 5mm bolts than the smaller 4mm bolts that are used. The cheap Chinese risers I had had so much slop in it, the handle bars were rocking back and forth. I couldn't get it out. This one looks more expensive than it is. The rise degree indicator is accurate. The quality of some of the "name brand" risers is probably the same. All of it was made in China.

👤I put this on my Fatboy to raise my handlebars. There is a The unit looks amazing, matches the bike's finish very well and has a very solid feel to it. I'm a new bike maintenance person, but I recommend that the handlebars be screwed on during the installation process. The screw holes didn't line up exactly when I attached the handlebars, because I removed that immediately. Less than half a millimeter off. I loosened the angle adjustment screw and took some plastic wedges between the sides to allow me to secure it with screws again. I like how it turned out. If I want to go back to the trails, it is totally changeable.

👤The hassle of changing everything over on new handlebars was thrown into the mix when these brought my stock handlebars up 4 inches. Everything was kept tight. The length is 5 1/2 ". The stock stem was 1 1/2 inches.

👤The handlebars had to come up to relieve the pressure on my hands. The riser helped a lot. No issues so far. I put butterfly bars on this bike. What a change! The bars and riser worked well together. The best bike mod I have ever done. This riser gave me a lot of options and angles to work with.

👤After 3 tries, this one actually fits real mountain bike bars. The only downside is that you will need an extra spacer to make the neck fit the stem and be tightened from the top properly. I had one laying on the floor. If you plan on using this neck, I would recommend buying some. Thank you.

👤It was easy to install on the gray Vista bike. I wish I didn't have to return the bike because of the poor transportation. The steam would make the bike look better and more comfortable.

👤I used this to increase the height of my handlebars. It worked out great. It is easy to assemble. You should know the diameter of the handle bars. Originally purchased for my wife. She had 1” in diameter.

3. UPANBIKE 22 2mm25 4mm Aluminum Gooseneck Length

UPANBIKE 22 2mm25 4mm Aluminum Gooseneck Length

Most mountain bikes, road bike, fixed gear bicycle, BMX, and MTB have a universal bicycle stem. The handlebar is 25.4mm in diameter. The fork tube has a diameter of 22.2mm. The stem length is 40mm or 80mm. There are millimetres. The stem rise angle is 30.

Brand: Upanbike

👤The bike I bought was too large for me. The handlebars were brought down to get the right fit. If you want to mount the handlebars, you will have to remove the levers on the other side. It was very easy to install.

👤It's easy to install. When the stem is raised to about a half inch lower than the max, there is no flex. The upper position. There was no side slip. Our new Schwinn trike is perfect. There is a Ps. I have been working on bikes for 50 years. I usually don't like these kind of stems because of the flex, but the price on this one is right and the bike fit is perfect. Great deal.

👤I had to raise my handlebars to take some of the stress off my shoulders. The bike stem worked well. It was easy to install, and seems like it was good quality.

👤The stems put you on the bike so you can enjoy your ride without neck and back problems. It makes your ride more efficient.

👤The stem was too small for me. The finish and design are very nice.

👤The stem's wedge wouldn't grip the inner steerer tube, which allowed the handlebars and front tire to be moved in opposite directions, so I wouldn't give it a 4 star rating. The old wedge worked after I replaced it with a new one. The rest of the stem was advertised and works.

👤My kid's bike has more life because the handlebars can now be raised, so it will fit him for a few years.

👤It isn't a nitto. It is also not $70. It does its job perfectly and doesn't look bad.

👤I bought this because I wanted to get more height in my handlebars and move it closer to the seat. I question the quality. I think I might have gotten a returned item as the finish had some scratches near the mount, but it's not important for me as my bike is vintage and scratched. The plastic cap does not fit, I had to use the one that came with the bike, the shaft wedge function is questionable, and the handlebars came off center while riding on bumpy ground. I may have to use the stock stem's wedge to get around it. I found that the Torque on the handlebars needs to be tighter than I thought it was, and I am afraid that it might break, so I needquing specs to help. If it breaks, I will tighten it and ask for a return. For the price, and re-using of existing parts, it is okay.

4. LQ Industrial Extender 0 87inch Threadless

LQ Industrial Extender 0 87inch Threadless

It's perfect for most bikes. The quill riser extender can be used on most bikes with a threadless steerer. The material is aluminum alloy. The packing is 1PC. The total length is 160mm, the bottom diameter is 18.6mm, and the steering tube is 22.2mm. It can be used for a long time. The oblique opening causes the screw rod, oblique nut, and the tube to be in a different position after the heart is inserted. All size bicycles are suitable.

Brand: Lq Industrial

👤The look of it is nice. It could have been a bit longer but this is fine.

👤Good thing. Light weight. A delivery person was sick.

5. SENQI 22 2×25 4mm Electroplating Gooseneck 80×220×240

SENQI 22 2%C3%9725 4mm Electroplating Gooseneck 80%C3%97220%C3%97240

The stem is 25.4mm in diameter. The handlebar is 25.1 inches in diameter. The fork Clamp has a diameter of 22.2 MM.

Brand: Senqi

👤I rebuild bikes that are fun to ride. I was looking for a riser stem that was vintage. There is a The stem looks good. It was shiny and smooth. You may notice the cheapness if you spend more than 5 seconds. It is quite heavy. The metal is finished and shiny, which is what you would expect from a 20 buck part. The head cap screw is not low enough to be set in the counterbore. Even when tightened, it sticks out. Unless the manufacturer corrects the design oversight, it will show up in every copy. The counterbore is not centered on the tapped hole. I don't know if that is a random defect or a tooling setup problem. It works, but it looks ugly. I noticed that the travel was not smooth when I ran the screw up and down. The metal fragments were stuck to the tip of the screw. The manufacturer didn't clean the chips well after the operation. Again, doesn't hurt anything, but it hurts for quality. There is a You get what you pay for at the end of the day. There are small defects on the 20 buck quill stem.

👤I bought this bike 3 years ago so that I could get back into bicycling after 30 years of motorized two-wheeling adventures. I was unable to find one that was longer than 180mm, but it did make the target. The one that hit the bulls-eye did not go past the safety margin line. I'm glad I found it.

👤I can't speak to the function of the bike stem because it was the wrong one for my bike. It was moved around the counter for a few days and didn't show any wear or scratches. It was high quality and sturdy. I was disappointed that I didn't pay more attention to the item I ordered because it seemed like a quality item and I wish it would have fit right.

👤I bought the silver quill stem to upgrade my Schwinn road bike from drop bars to upright handlebars. The stem did the trick. I bought the longest one, but it doesn't seem to be available at the moment. There were no complaints. I bought a second stem to convert the same era vintage Schwinn for my son who doesn't like drop bars.

👤Beautifully finished and with a longer quill, but not so long as a nitto technomic. I had to use a pry bar to open the clamp to get over the curves of the drop handle bar. It would be 5 stars if it wasn't 5 stars.

6. Profile Design Threadless Size Converter

Profile Design Threadless Size Converter

Delta products ensure a more enjoyable ride. Delta is the brand you can trust with the best customer support in the U.S. All quill style forks are converted to use threadless stems. It converts 1 inch to 1-1/8" threadless.

Brand: Profile Designs

👤This is a good-looking aluminum accessory that can be used to mount a newer style stem on a bike with an older steering tube. There are two things to pay attention to. Many buyers seem surprised that you are buying the right size. When your bike has a 1 inch steering tube, the shaft that fits inside the stem will be thinner. If your old stem is less than 2mm thick, this is the correct accessory for you. You may not be able to see the tube on many bikes because your steerer is measured on its outside. The steerer is not 1 if the shaft of the old stem is thicker than 2mm. The thicker top part of the shaft is where the new stem should be mounted. The stems that are taken are 1 1/8"/28.8mm, a common size. 2. The top cap on this one is wider than the opening in your stem. You can't mount the stem on the bike and then on the adapter. You'll need to assemble the adapter and stem, then put the combined unit into the steering tube. A cap that covers the joint between the stem and the adapter is the payoff for your efforts. It will likely keep water out of your assembly.

👤The part installs into a tube that's 22.2mm in diameter to convert your old style handlebar stem to a modern one. The expanding style stems of older mountain bikes limit your configurations and options for changing your bike around to fit you better or just to use modern components since there are far more options now. Make sure you have a tube on your bike. If you want to avoid a delay, measure it. I converted two of my vintage bikes with these stem conversion tools. With so many options on the market, prices are great and you can replace those aging, ugly stems or make that old bike fit better- in my case, I needed to raise the bars since I'm getting a bit older and need a more upright riding position. There is a I replaced the rusty Ritchey stem with a new one and it cost more than a new stem conversion, new handlebars and a new stem. The marketing hype they use to try to sell new bikes is more hype than benefits to the average rider. You can buy a used bike for $300 and ride it in style. It's a good thing.

👤Bike stems are not normal. The OD of most 1" stems is 22.2. There is a The stem is actually 25.4. Some of the other reviews had pictures of stems that arrived from this item, so I ordered this one. I bought this to use on my old bike. The stem is marked OD 22.2. I was really hopeful that the reviewers had posted pictures of a 25.4mm OD. There is a I can use the stem I received as a replacement for a 1" quill stem. The seller should add metric description and pictures to the item. It is easier to verify a 25.4 OD stem for your bike than it is to measure it. It looks like a well made part. I'll keep it for an old bike that needs an accessory.

7. Wake Adjustable Mountain Handlebar Lightweight

Wake Adjustable Mountain Handlebar Lightweight

CYCLING COMFORTABLY: Handling more flexible, much easier to force when climbing, lighter weight, comfortable and convenient to operate, effective bicycle fork extender. The diameter of the tube is 28.6mm (1-1/8"), the handlebar is 31.8mm (1-1/4"), and the length is 90mm. It is adjusted. Light weight, hollow design. Please make sure you confirm your size before purchasing. The four bolt bar is in position. Simply connect the original fork stem to the new one. A universal short handle bar stem is suitable for most bikes.

Brand: Wake

👤I have an issue with my own and I am subtracting one star. I was impressed with the quality of the unit. I tightened the locking screw after adjusting to the desired angle and noticed there was still movement at the joint. I tried to tighten the screw but it wouldn't tighten and the joint was still loose. When the screw is tightened, the joints have teeth that mesh, but in my case they were not fully meshing. I noticed the problem after removing the screw completely. When you loosen the screw, the spring inside pushes the joint ends apart. The spring in mine was too long and was being fully compressed when the screw was tightened. I used a pair of diagonal cutters to cut off the spring length. The joint is locked solid with no movement even with only moderate tightening of the screw. I noticed that people who had this issue broke the unit or stripped the screw trying to tighten the joint not realizing it was the spring inside the joint causing the problem. I hope this will help other people. There is a The bike is much more comfortable to ride after this was installed on my bike, and I like it because I can adjust the handlebars up to a better position.

👤I am a tall person, as stated in my review. I bought a new bicycle to replace a bicycle that was 10 years old. The seat of the bicycle will be extended significantly if I need a XXL bicycle. I was putting a lot of weight on my hands because the handlebars were low. My hands became numb after a few miles. I reversed the bicycle stem to point upward because the store installed it for aggressive riding. This made a difference. Most of the bicycle stems I looked for were fixed. When I saw that it had positive teeth engagement, I found this one. I decided to try it. I tried a 30 degree adjustment and ended up at the 60 degree adjustment. I like this better than an extension because it doesn't increase the moment and stresses in the bicycle stem. I can now ride 20 miles with no hands going numb.

👤I'm very pleased with my purchase of the Wake MTB varaiable stem. I was a little worried about the quality for the price. I'm happy to report that these feel just as good as any big name brand stem. The variable geometry will be useful on my hybrid road conversion project. I was worried if one could get the pivot bolt tight enough to keep the stem from moving. When you hit something. This was a non-issue. The inner part of the linkage is called a rosette surface. A bunch of "V's". It doesn't budge once it's tightened down. * 5 Stars: Works exactly as advertised, fit/finish are what you'd expect when purchasing this type of product, and it is a good value, 4 Stars: Works exactly as advertised, fit/finish are what you'd expect when purchasing this type of product, and it is I'd change a few things, 2 Stars: Barely works but can be made useful if you try, and 1 Star: Useless, does not perform it's intended function, and is generally a waste of money.

8. Extender Handlebar Aluminium Mountain Extended

Extender Handlebar Aluminium Mountain Extended

The instructions are given. The wrench should be used in the direction that the front wheel points for installing the pedal. Strong material: forged aluminum alloy material, solid and firm handlebar extender, durable for more safety when used. The stem riser can adjust the gasket to fit your height, which will reduce the pressure of the waist and raise you to your comfortable position. Simply connect up the original bicycle fork stem. Most of the Met bikes have a handlebar riser. Handling more flexible, light weight, much easier to force when climbing, is comfortable, convenient bike fork extender. Most of the Met bikes are compatible with work on mountain or road bikes with thread less Steering tube. The bike fork extender is convenient.

Brand: Emoly

👤The product has a number of design flaws that make it very unsafe. It is unsafe because it doesn't allow it to be tightened enough to keep the fork from rotating. If you have more than 15 pounds of pressure and your bars and front wheel are not aligned, you can turn the bars without the wheel moving. There is a The shape of the bolt threads in the threaded end is the worst flaw. It means that one side has more threads to hold the bolt than the other. If it was better material than a cheaper one, it would be sufficient when tightened. It is shaped that way and that makes it hard to use a stop nut behind the integrated threads. The bolt was bent by the use of an angle washer and stop nut. There is a This is the product for broken bones.

👤I reviewed many of the STEM Extenders because the handle bars were too low and I wanted to ride my mountain bike in a more natural position. The instructions were clear. The tools were provided. Good construction. I enjoy riding my bike and feel accomplished. Best to everyone.

👤After taking off a few years, we are getting back into biking. The husband put a lot of money into his ebike. I wanted to keep my Diamondback. I found my hands and neck were not comfortable at the angles that have been an issue before. The problem was solved by this extender. It looks great on my black bike with red accents, and it gives me a solid gripping area when I load it onto the rack. It's easy to install. Very pleased!

👤The design of the stem extension is solid. The product is pretty nice and the anodizing process makes it feel high quality, even though I was skeptical at first. Highly recommended.

👤You pop this on top of the steerer. Just remove 3 bolts. Next, screw them back in place. You can't stop smiling when you ride a bike that fits all of a sudden. Wake up dude, wake up now! Welcome back to reality! Good morning America! It was a dream. You can only turn the steering wheel 8 degrees to the right and 8 degrees to the left in real life. Why amigo? The steering wheel range of motion is limited by the stretched brake cables. If you already have long cables and housings, you are one lucky guy. Don't forget to contact me if you win a lot, I will get 10% of your winnings. Remember, it was my idea?

👤There was a gap between the bike steering stem and the extender after it was installed. The inside dimensions of the extender do not allow it to seat properly. The problem could be solved by changing the inside dimensions of the extender to match the dimensions of the bike stem, or by using a ring to close the gap between the extender and the handlebars.

👤Allen stripped the threads when they were tightened.

9. Sunlite Piston 2 Bolt Clamp Silver

Sunlite Piston 2 Bolt Clamp Silver

The bike can be upgraded. Downhill, Chongshan, climbing, are very comfortable. The stem is 250mm x 22.2mm. x 40mm The forged alloy body is made of material.

Brand: Sunlite

👤I wanted a hybrid bike to jump on for family rides, without having to use my road bike or mtb bike. It wasn't enjoyable to just cruise around on a road bike. I was going to either spend $500 on a decent hybrid or find a way to modify the beater. For $16 and another $10 you can get a longer front brake cable. It is really nice to ride and it looks rediculous. The stem is not twitchy when out of the saddle and there is no flex in it. I'm very happy with the stem. I did this because I wanted a bike.

👤It worked perfectly for a month and 700 miles. It fit an inexpensive mountain bike with a standard cruiser fork, headset, and handlebar. It doesn't need to be retightened. Grease was added to the bolts. It made a new bike feel comfortable. The long stem helps tall riders sit upright. The product photo made the stem clamp look thin, but it completely covered the handlebars with only a small amount of lines visible on either side. The product is appealing and has a great value.

👤This is on a stout stem. It was easy to cut down. This is for an older 90s hybrid. It handles it with some force. If you like handling your whip quickly, this is it. It is very long. I had to find another shorter wedge bolt after cutting mine down.

👤A steel stem with a cast aluminum handlebars. I was expecting all aluminum, but it was much heavier than I thought.

👤I have been using this for two months and have not had any problems.

👤I needed to raise my handlebars for a more upright riding position. I installed it backwards. It's nice to have a two bolt setup for the bars. The weight is not nice. This thing is very heavy. It's not something that one would want to install on a light weight bicycle.

👤The Sunlite TCO will get you into a comfortable position. There is a It's a position that lets you keep your eyes up. It has been reliable for me, and I have traveled thousands of winter miles in Boston.

👤I wanted a tall stem. It works well. It's heavy, but it's used for a specific purpose -- I adapted an old road bike to a flat bar fast bike and wanted to have an upright riding position. It seems well made.

10. FOMTOR Riser Handlebar Extender Mountain

FOMTOR Riser Handlebar Extender Mountain

A universal short handle bar stem is suitable for most bikes. The maximum height extension is 70mm. There are 4 spacers, 1 x 10mm and 3 x 5mm. The height can be increased up to 70mm. Simply connect the original front fork stem to the new one. Light weight. It is made of high-strength T6 aluminum alloy. Handling more flexible, light weight, easier to force is comfortable. It's suitable for 1-1/8" 28.6mm Fork Mountain Bike, Road bike, Track bike, Folding bike, MTB BMX...

Brand: Fomtor

👤The stem riser extender worked well. Before this extender, I could have raised my seat to the proper height for my legs, or I could have put my seat too low for my legs, with good upper body posture. The performance of the extender is good. The bolts are smaller than the original neck bolts. I gave the extender 5 stars because they are holding. I will look for an extension with beefier bolts if they fail. Installation took longer than expected, but not because of the product. The nut in my stem was a little crooked, but it wasn't noticeable on the short bolt. I wonder if those people had a crooked stem nut assembly like me, because I read a number of reviews that the long bolt was bent. The graphic I attached shows what I found. I lightly tapped the head of the bolt with my finger to make sure the stem nut was straight. The stem bolt on my bike is held in place by 2 star shaped pieces of steel. It was not very precise, but easily straightened. The long bolt worked perfectly when the nut was straightened.

👤The stock steer tube on the 2012 Trek 3500 was too low for the current rider, and the handlebars were too low for the original 2012 Trek 3500. Those in need of an elevated handlebar need a stem extender. There is a The FOMTOR stem extender is an excellent quality aftermarket bike doodad. It has nearly four inches of vertical position. It includes a long titanium bolt to reach the distant star nut, six aluminum spacer rings, and a matching cap. There is a The FOMTOR stem extender was perfect for the existing steer tube. The titanium stem bolt is stout enough to hold the entire headset in place, and appears to resist dynamic loads and stresses under normal use. Black powder coat finish is what the stem extender, cap, and spacer rings are made of. There is a It's annnnnd... I bought the last one on Amazon. I need two more.

👤I used these for my bike. It made a huge difference in my riding position. The height to the bikes handle bars was increased by the spacers. I liked that it was all plain black and not colored. The end was very clean.

👤The bent bolt makes it hard to install with the new cap. The stock cap is not centered because it was not used without the recess. The bolt would be 5 stars if it wasn't bent.

👤It was my fault that I didn't double check the measurements for the bike I am fixing up. I won't be returning it because I am hopeful it will fit on another family member's bike. I was sad it didn't fit on my body, but it looks like it's very high quality. Will update this review if it works for the other bike.

👤The extender tightens down when it connects to my fork tube. I had the right amount of spacers and the extender fit my new stem perfectly. I am happy with my purchase and would purchase again.

11. Wake Extender Handlebar Aluminium Adjustable

Wake Extender Handlebar Aluminium Adjustable

Handling more flexible, light weight is easier to do. 1. The maximum height extension is 180mm. There are 6 gaskets, 2 x 20mm, 3 x 10mm, and 1 x 5mm. You can adjust the gasket to fit your height. 2. Simply connect the original front fork stem to the new one. 3. The forged aluminum material has a polished anodized finish. 4. It is suitable for most bike with threadless headset. 5. Handling more flexible, light weight is easier to do.

Brand: Wake

👤The spouse and I took the bikes out today. It was noticeable that there was no wrist, hand, shoulder, or back pain after about 14-16 miles. I might even buy a stem that can be adjusted to fit my body, and maybe even buy upright grips, since I am going to try some more rides. The benefits are well worth the minimal cost of experimentation. Do you want to come back from a long ride achy or do you prefer to spend money and make your ride comfortable? There is a The product arrived in two days. I had looked for videos on the internet before the event. Installation was not good. It took about 10 minutes. I bought two of these for my spouse and myself because I had just bought two e bikes for them. The handle bars on the bikes were too low and caused us both to lean too far forward which resulted in wrist, hand, shoulder and back pain. The ride is much more comfortable now that I raised the bars up. If you have a mountain bike, you might want to consider one of these.

👤This is what I needed to stop my hands from feeling numb. It wasn't too long for me. The handlebars were the same height as my seat when I adjusted the pedals, but I'm 6'2” and on a large frame fat-bike. The poor geometry was fixed by this. There is a It's very sturdy with no creaking. I weigh over 300 lbs. It holds up well with me. I'm very happy with it.

👤This product does what I need it to. I can ride without hunching over. There is a There is one thing to note. The front brake line has a limited amount of slack, so it is a good idea to buy a much longer brake line or cable. The item allows for a big change to the handlebars.

👤Awesome. It doesn't raise the handlebars to the max. The total length of this product is that. It doesn't take into account that you have to use about 50mm or 2 to bolt it on. It's about 130mm or 5. It's still great. If you need more, put some above. It would stick up 130mm. I think you could remove the top spacers and cut the bolt if that bothered you.

👤I am happy that it raised my handlebars. I needed extra ones, so I had the previous one. It was fine. I didn't try to tighten it. It comes with a spider, a spider web, pumpkin, and a white cloud, but the rest didn't make sense to me. Someone in the comments or question area noted the same thing and wanted to remove the decals. I used cotton pads to apply finger nail polish. I removed the top layer, but you can still see the white over the black ground. I am going to use a tooth brush and fingernail polish this week. I think I can get it all off. I am happy with my purchase. I bought another extender a month earlier, which was about 2.75 inches shorter than this one, and it was good. When I bought this one, I had to replace all my cables because my old ones became too short, and I couldn't get my brake and shift levers back onto my handlebars. I bought Jagwire cables that are longer. I had to buy new housing and cable for both the brakes and shift, and each cost me about $30 or $35. I watched a video on how to adjust a front and rear derailleur. I would recommend buying the orange Klunker Commuter Urban Bicycle Handlebar and the Champ Oversized Comfort Bike Seat. I can ride a 25 mile ride now that I can sit up straight.

Summary

What is the best product for bicycle quill stem extender?

Bicycle quill stem extender products from Sunlite. In this article about bicycle quill stem extender you can see why people choose the product. Cxwxc and Upanbike are also good brands to look for when you are finding bicycle quill stem extender.

What are the best brands for bicycle quill stem extender?

Sunlite, Cxwxc and Upanbike are some of the best brands that chosen by people for bicycle quill stem extender. Find the detail in this article. Lq Industrial, Senqi and Profile Designs are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com