The original setup in the shoulders, arms, and back had to be corrected to achieve a more comfortable riding position. The stem and riser handlebar allow you to sit upright on the bike, which is better for your back. Only fit for Handlebar diameter 31.8mm, front fork stem diameter 28.6mm, and Length: 120mm. The only handlebars that this fit for are 31.8mm. Do not fit bars larger than 25.4mm. Measure the diameter of your bandlebards before you buy them. The angle is 0 60. The height extension is 90mm. The weight is made of high-strength, high-quality aluminum. Before you buy it, please confirm your handlebar is 31.8mm. It's easy to connect up the original fork stem. The four bolt bar is in position.
👤My seat was making me uncomfortable. I was able to tease out that my handlebars made me lean forward, because they were set that way. I was forced to sit on my seat because of that leaning forward. There was no way to adjust the handlebars on my Giant Commuter bike. I found this post after a lot of research. I used a simple procedure to change out the old handlebar post for this one, and it is perfect for me now. A new bike is much more expensive. It works very well. I'm no longer leaning on the handlebars. That was very painful. The only concern with any part that is variable, changeable and handles the total steering of a bike, plus handles your full weight against it, is to make sure the screws are tight. The bar will not have any issues if they are tight. It would be disastrous if the bar moved on you because of regular checks. This item is a must have for me. When ordering, there are choices in length. Take the time to analyze what you need to fix your issue. This was a relief for me. My biking world has changed completely. I give it 5 stars.
👤It was installed on a Cannondale aluminumCAAD8. I ride 6,000 miles a year, but use multiple bikes. There is a The only drawbacks to this item are that it is heavier than many road bike stems, it is a little less aerodynamic, and it looks a bit clunkier. There is a If you can get past those things, you will like the way it is made and reliable, and you can adjust your riding position for comfort. That is what makes it worth it. There is a I am unwilling to test a stem that is so lightweight I can go down a roller at 35 mph. I need to know that my bike will hold up even if I hit something. I'm probably buying one for my wife. She says she needs to reach a little further for her reach.
👤I was uncomfortable on my bike because I had to lean forward too much. I found this and it made me feel better about how I ride. I wish I had found this years ago.
👤I bought this to make my bike more stable. The stem is skinnier than the Bontrager that came on my Trek Roscoe 7 and that is the only issue with the install. The fork wiggled when riding and braking. I dropped in to my bike shop and bought a set that allowed me to take over. The bike shop said that fish should be extended beyond the top tube to have something to press on. The answer was not to crank down on the top cap bolt. I did break one of the bolts, but it may have been a torgue wrench user error. It was easy to drill the bolt and get it to back out. I set it at 60 degrees so that I can play with it to find the best setting.
Features a sleek and modern look. Fit for front fork stem diameter 28.6mm (1-1/8") and handlebar diameter 31.8mm (1.25''). The weight is 205g. The angle is 45 degree. Simply connect the original fork stem to the new one. The four bolt bar is in position. It's suitable for most road bike, mountain bike, track bike, and BMX. The front fork stem diameter is 28.6mm and the handlebar diameter is 31.8mm. Before you buy it, please confirm the diameter of your handlebars.
👤I needed a stem to make my wife's bike more upright. The size and angle of the handlebars help achieve that goal. It seems strong enough to handle day-to-day use and works great. I didn't want to spend a lot of money and this stem is cheap. Bad things. The stem doesn't fit well. The fork steerer tube has to be tightened a lot more than normal to make it grip the handlebar. The tension on the headset bearings changed when I did this. It took some fiddling to get everything right. You get what you pay for. If you're willing to pay for it, it's an ok product, and if that's what you're looking for, it's your stem. If you want a component that is precise, look elsewhere.
👤The stem raises my handlebars. It is large and heavy, but seems good quality. Other reviewers have used the word "choking" as a description. The connection to the tube is long and I removed a riser for a safe fit. The fomtor uno 35 degree 70mm stem was too short for me. If you want something lighter, you might consider the uno stem in 90mm or 120mm.
👤I have a bad shoulder and my mountain bike is hard to ride. I wanted to raise the handle bar to relieve the stress on the shoulder. That was done by this stem. It was quick and easy to install. It was well made. The handle bars were raised to make my body more upright. Would recommend this to anyone who wants to improve their rides.
👤It does a good job. My handlebars are now at a more comfortable height and distance, which allows me to ride in a more upright position. There is a I was surprised at how heavy it is. It is more heavy than my previous stem. Either it's made of a heavier metal or thicker. A few ounces on my mountain bike isn't a big deal. I wish the cap was open in the middle like other stems are. It would have made it easier to make sure the handlebars are centered. The handlebar cap is solid, which increases the weight and decreases the usefulness, but gives them another place to shamelessly place their huge logo.
👤I wish the front plated didn't block my design. It would be perfect if it were seethrough like the 35 degree version.
👤The stem is a back saver. The perfect solution was to raise my position. The 45 degree rise moves you back onto your saddle more. The stem is very strong and very confident. There is a I would buy this again.
👤I made a mistake and ordered this for my beach cruiser. I needed to make this work with my handlebars because I enjoyed the quality of the stem. I ordered some parts. I fixed my error. Measure the handlebars to make sure you get the correct stem.
👤I needed to get a bit taller. This stem does it with the steep angle, but the portion that connects to the stem is taller than my old one, which lowered the handlebars a bit. It works well, seems sturdy, and no creaking or other noises are heard when installed.
Delta products ensure a more enjoyable ride. Delta is the brand you can trust with the best customer support in the U.S. All quill style forks are converted to use threadless stems. It converts 1 inch to 1-1/8" threadless.
👤This is a good-looking aluminum accessory that can be used to mount a newer style stem on a bike with an older steering tube. There are two things to pay attention to. Many buyers seem surprised that you are buying the right size. When your bike has a 1 inch steering tube, the shaft that fits inside the stem will be thinner. If your old stem is less than 2mm thick, this is the correct accessory for you. You may not be able to see the tube on many bikes because your steerer is measured on its outside. The steerer is not 1 if the shaft of the old stem is thicker than 2mm. The thicker top part of the shaft is where the new stem should be mounted. The stems that are taken are 1 1/8"/28.8mm, a common size. 2. The top cap on this one is wider than the opening in your stem. You can't mount the stem on the bike and then on the adapter. You'll need to assemble the adapter and stem, then put the combined unit into the steering tube. A cap that covers the joint between the stem and the adapter is the payoff for your efforts. It will likely keep water out of your assembly.
👤The part installs into a tube that's 22.2mm in diameter to convert your old style handlebar stem to a modern one. The expanding style stems of older mountain bikes limit your configurations and options for changing your bike around to fit you better or just to use modern components since there are far more options now. Make sure you have a tube on your bike. If you want to avoid a delay, measure it. I converted two of my vintage bikes with these stem conversion tools. With so many options on the market, prices are great and you can replace those aging, ugly stems or make that old bike fit better- in my case, I needed to raise the bars since I'm getting a bit older and need a more upright riding position. There is a I replaced the rusty Ritchey stem with a new one and it cost more than a new stem conversion, new handlebars and a new stem. The marketing hype they use to try to sell new bikes is more hype than benefits to the average rider. You can buy a used bike for $300 and ride it in style. It's a good thing.
👤Bike stems are not normal. The OD of most 1" stems is 22.2. There is a The stem is actually 25.4. Some of the other reviews had pictures of stems that arrived from this item, so I ordered this one. I bought this to use on my old bike. The stem is marked OD 22.2. I was really hopeful that the reviewers had posted pictures of a 25.4mm OD. There is a I can use the stem I received as a replacement for a 1" quill stem. The seller should add metric description and pictures to the item. It is easier to verify a 25.4 OD stem for your bike than it is to measure it. It looks like a well made part. I'll keep it for an old bike that needs an accessory.
More flexible handling, light weight, easier climbing force, comfortable operation, convenient bicycle fork extender are some of the things that make cycling comfortable. Installation is easy with the fito twin-bolt design. You don't have to remove the shifter or grip in order to install the handgun bar. The material is light weight and anti-rust. For 1 inch (25.4mm) hands. The center measurement of the hand bar might be different from the end measurement. Before purchasing, please make sure you know the measurement of where the stem is located on the handle bar. The measurement is 7/8" (22.2mm). Also available in silver. Please search for the ASIN number "B00ATT6TSO".
👤The aluminum stem has a nice finish. An excellent replacement for a steel stem hybrid. Add bars and ounces. The bars and stem combo are lighter.
👤This stem allows you to raise your handlebars in a comfortable way. I bought this one because the original stem on my bike could not be raised very far. I am very happy I did. There is a plate on the front of the bike that can be changed out. There is a The stem is working well and I am very comfortable on my bike now. I had it installed at the bike shop and it was done in a day or two.
👤This is a high quality product. I needed to replace a cracked stem on my vintage mountain bike. I wasn't expecting much because of the low price. I was wrong. The finish and quality exceeded my expectations. This is a long stem. I was able to get a bit more rise out of my bars, which helps my back. The product was very good.
👤The grip on the handlebars is too loose. The pipe has 1 inch center. There is a The handlebars turn even after the 2 screws are tightened. I had to drill a couple of holes to fit the handlebars. There is a This is not well designed if it is US made. It is well-made, but it is disappointing.
👤It looks good without the scratches. I was expecting a better package. The threads weren't of the quality and the bolts were stiff. I paid more for it but it works. Will update review once installed on my bike.
👤The screws don't sit down all the way. It was almost like there was the wrong size. Sending it back. I have a replacement for my review. The second one fit perfectly. It looks great on the bike.
👤They need to use lead in the alloy. Heavy for aluminum. If you want to keep your weight down, you may want to spend more money. It's great for the price and what I'm putting it on.
👤The product was easy to put on.
It's perfect for most bikes. The quill riser extender can be used on most bikes with a threadless steerer. The material is stronger and lighter than normal material. The height can be asdjusted from 53mm to 90mm with 4 Gaskets. It's easy to install with a professional design and fixed to the original fork stem. Adding 1 to 4 Gaskets on the stem and no tire will take care of your health. The color is black and the weight is black. Around 0.19 kilogram.
👤It is amazing how raising the handle bars a few inches makes it easier to see down the road and with less pressure on my hands. I have a bike seat that is extended so I can move my legs. The handle bars match the extension. It's easy to fit on my bike. There was no need to get new cables. Great idea.
👤If you don't know how much you need, it's a good option. The price seems good compared to the fixed length alternative.
👤Five minutes to install back out right and 25 miles a day, I am happy with this product.
👤The height problem I had on my mountain bike was solved by this device. It was high quality and met my expectations.
The handlebar diameter is 31.8mm, the front fork stem is 28.6mm and the length is 60mm. Light and durable. The weight is 115g. It is made of high-strength T6 aluminum alloy. Simply connect the original fork stem to the new one. The four bolt bar is in position. It's suitable for most road bike, mountain bike, folding bike, track bike, BMX, etc.
👤The threshold for quality is low. Graphics are looking good. Bolts are cheap. The part that grips the steerer tube is not completely symmetrical. The bottom part is very thin and the top part is larger than the stem, as shown in the pictures attached. It doesn't look right.
👤I wanted a shorter stem for my road bike and this one seemed too good to be true for the price. I bought a name brand one that was twice as expensive. The quality of the stem was the same as the name brand one. I have been out of the saddle a number of times and all is well. I now have a shorter stem.
👤I wanted to see if a shorter stem would be better for my neck and shoulders. It was a low-risk experiment because of the price. I've been on for a couple hundred miles and haven't had a problem. It's easy to install, decent hardware for the price, and no heavier than most big- branded stems, which I've had with other cheap hardware. It's a big win for me because my commute has been more comfortable with the shorter reach.
👤The 120mm factory size was replaced with the 90mm stem length. I wanted to bend in my arms on my gravel bike, but wanted less reach to the bars. The part seems to be well made and does not seem to differ in quality from the factory piece.
👤The Wake aluminum bar was a perfect fit for this. My mountain bike is a big box, dual suspension Schwinn 29er with a steel stem and handlebars that are way too narrow. I had to grind off a bit of the top of my steering tube to get everything to tighten down. My hand position is more comfortable because the stock stem length is half what the 60mm rise is. This stem is definitely recommended by me.
👤It was installed on the indoor trainer. The steerer tube is vertical and the trainer is on a level floor. The handlebars were measured to be tilted by about 1 degree. While this tilt may appear small, one can see a difference between the height of the left and right end of the handlebar. This is not how it should be. I don't want to sit on a bike that is not straight. You get what you paid for. Lesson learned. A Chinese brand that is low quality. I ordered a replacement stem from a bike store and am getting it back.
👤If you haven't adopted a short stem yet, you need to shorten your game and improve your confidence skills. I put one of these on my son's mountain bike and he said it felt different. He road with more confidence and took on challenges that he would have normally avoided. Great upgrade for your bike.
👤Quality appears good and the price is nice. What not to like? Good purchase.
What you will get. The length is 115mm or 180mm. There are 6 gaskets, 2 x 20mm, 3 x 10mm, and 1 x 5mm. 2. There are 2 gaskets, 1 x 10mm, and 1 x 5mm. You can adjust the gasket to fit your own height. The diameter of the tube is 28.6mm (1-1/8"), the handlebar is 31.8mm (1-1/4"), and the length is 90mm. Light weight design. The four bolt bar is in position. Simply connect the original fork stem to the new one. A universal short handle bar stem is suitable for most bikes.
👤It weighs 7.68 ounces and is definitely not T6 aluminum. It's not sure what it's made of. It could just snap in two with enough stress. Seeing that this is being used as a mountain bike part, it will be easy to see how much is needed to snap it. I will be asking for a full refund and throwing this in the trash. I am used to a certain level of testing and certification for products like this to make sure I am safe on the trail. This is concerning to me. "There is no consumer protection when products are sold on Amazon". Consumer protection also covers my safety and yours as well. I don't know if Amazon cares.
👤This is not a 90mm stem. I attached a diagram of how stems are measured, and it measures 105mm in that dimensions. It has a 45 degree angle. The measurement center is 74mm. I replaced a 70mm 7-degree steam and it increased the Reach just 2mm. Keeping Reach is important since moving the handlebars further away makes you lean over more, even if the handlebars are higher, and too little reach can lead to instability or twitchy steering. The part that is used to hold the steerer rube is over 2 feet tall. This is taller than many other stems, which is a good thing since it will reduce strain on the steerer tube. It means you'll probably need a lower space stack height because you don't want the top of the stem too far above the steerer tube. My handlebars were raised 35mm while I changed the reach to just 2mm. It should be perfect. The other stem on Amazon looks to be the same, but it comes in both 45 and 40 degree angles. This one is the same price as the other one. That one appears to have the same mistake. There is a If you want a brand for safety, the best one I could find is this Ritchey: https://www.amazon.com/Ritchey-Comp-4-Axis-Stem-Degree/dp/B07VYKZ38W It's only 30 degrees, but comes in various lengths. The "comp" version is only 80mm in length. There is a If the Wake stem is marked as 3D forged, it would be a good sign of strength. It's hard to believe that the weight and price are so high.
👤I wanted a more upright riding position on my trail bike in order to see what was going on around me. I thought moving my hands back and up around 50mm would do the trick. I was looking for a set of handlebars that would give me the rise and sweep I was looking for. Some handlebar sellers don't give specific dimensions for the bars they sell. I thought about replacing the stem because of the cost and the quality of bars. The Wake stem is 90mm long with a 45 degree rise, which is the same length as the old stem. My hands are now about 2 1/2 inches further back and about 2 inches higher than before, because I used the same flat bar on the bike. It was perfect for what I wanted and a better posture for trails. The product is well made and finished, with thicker tube walls and a taller steering tube collar than the stem it replaced. Only marginally heavier, and beefier. It is easier to swap out a stem than it is to swap out a bar. The low end bars are $30-50. It's easier to determine how the new product will affect your ergonomics.
There are 4 sizes of bike handlebar spacers in this package. Each size provides a combination to adjust the height of the handlebars to fit your riding style. Bicycle headset spacers threadless are made of black anodized aluminum alloy material with smooth surface and exquisite workmanship, eco-friendly, sturdy and durable to use. Stem spacers road bike inner diameter is 28.6mm, 1-1/8" headset set, compatible with 28.6mm front stem fork of mountain bike, road bike etc. There is a feature. The aluminum headset spacer is more sturdy and resistant to damage than carbon fiber headset spacers, and it's 888-282-0465. If you go for a heavy duty off road ride, you should use aluminum spacers other than carbon, due to automatic cutting, smooth edge, and fit most of the road bicycles.
👤The stems on the two bikes I changed had 3 x 10mm spacers on them. I didn't know how I would position the spacers, and I didn't know the exact measurement of the bike's bar height. The kit was perfect. I used this product above the stem to place 20mm below and 7mm above. The other placee is 20mm + 4mm. These are an excellent value, and work exactly as I had homes. If I make changes again to this bike or others, I am set.
👤These work well, but they aren't as thick as the factory spacers on my or my son's bikes. It's a good value for the price and the selection of spacers. It's very easy to get the correct rise to allow for the 3mm gap between the steerer tube and the cap.
👤The image in the listing does not match what is in the description. There are three different types of spacers in the photo. The spacers they ship are 2, 3, and 10mm. When they arrive, you will be disappointed if you go off the photo.
👤The new handle bar was what I needed. I didn't think about needing spacers when I ordered the bike stem. I ordered this set and it arrived very quickly. It was nice to have different types of spacers.
👤These seem to work well and match the other ones on my Trek. I have had one of the spacers on my bike for a month and so far no issues. Will keep you updated if something changes.
👤The spacers were smooth with no burs and consistent sizes. There are 12 different sizes of the bag. You could buy a couple at the store. These are nice to have around.
👤There are 12 pieces for the price of 2. Good quality. I like aluminum more than carbon fiber. These mountain bikes will not fail because I can be hard on them. The handle bar height can be a problem if you don't have a good selection of sizes. For the next project, spare.
👤It worked out as planned. Good quality. There were no problems. Take accurate measurements.
👤This is a good set. The set has enough pieces to adjust more than one bike. They are lightweight and durable. The price was good and the shipping was fast, which was a plus.
👤Needed to install a new bike stem. There are lots of different sizes of Qurans.
👤There were different sizes of spacers. Excellent quality. They do what they're supposed to do. The product was good and the seller did a good job with it.
👤Good quality work.
It's suitable for 1-1/8" 28.6mm Fork Mountain Bike, Road bike, Track bike, Folding bike, MTB BMX... If you have a handlebar diameter of 25.4mm, please select a stem with a diameter of 25.4mm. If you have a handlebar diameter of 31.8MM, please choose a stem with a diameter of 31.8MM. The handlebars have a diameter of 31.8 MM. If your handlebars have a diameter of 25.4MM, please choose another. The material is aluminum alloy. High strength, forged alloy construction. Weight: 260g. They love to communicate with their customers. If you have a question about their products or delivery time, just contact them and they will reply within 24 hours.
👤This is easy to install. I have a mountain bike with straight bars and am looking for an extension. The local bike shop only had a bmx handlebar for sale. No thanks. I adjusted my bar to where I wanted it.
👤The device lifted up the handlebars and bought me the handlebars closer to me, even though I had a back injury and was leaning forward on the road bike. I can ride again without neck pain and I did not have to buy a new bike. It was easy to install, but you have to adjust the front brake cable.
👤This made a huge difference in my comfort as I am on a too large frame to fit a large battery pack in the larger triangle that came with the large frame. The hand numbness that I was having 10 minutes into my commute has been eliminated by raising the bars closer to sit more upright. I made my own as I ordered a large one, I believe there is an alternative you can buy.
👤The hybrid bike has a threadless stem. I'm taller than the average woman and it's all in the legs. I couldn't even reach my handlebars once I adjusted the seat properly, but luckily this is the perfect replacement and was just as easy to install as the standard one that came with the bike. No more riding like a pretzel. If you need more than two extra inches, find a different model.
👤I used this stem to get a lower, more road-like riding position on my hybrid bike. It seems like the opposite of how most people are using these, but it shows that you can angle the stem upwards or downwards. I chose this stem because it showed a + range of angles, but I think all similar stems will be able to be set the same. This item is very sturdy and large, with a good thickness of metal around the bolts. The finish is good and all of the bolts are made of steel. It comes with a 5mm spacer and three allen keys.
👤The low handlebars on my bike caused a lot of pain in my shoulder and back, which was a gift from a career in the Army. This was what I needed. Depending on what you need, the stem can provide 3 inches of elevation. It only took about 5 minutes to get back on the road.
👤One thing I don't like is being able to move my handle bar up to a more comfortable position. I asked them for the extentions of the trim ring. I don't think customer service is good when they refer you to a new purchase instead of sending you the stems. When I was shopping for a stem, I found that all of the stems were in the pack. Maybe I should have bought one of those.
👤Works are described. It was a perfect fit for me to sit straight up and perfect the balance of my bike. Excellent product would definitely recommend!
We love to communicate with their customers. If you have a question about their products or delivery time, just contact them and they will reply within 24 hours. Please confirm your bike's diameter is 31.8mm (1-1/4") and fork steerer tube diameter is 28.6mm (1-1/8") before you place your order. The item isn't suitable for your bike. The degree is adjusted to 0-60. It's not applicable to Giant bicycles. The mountain bike stem is made of high strength aluminum. The MTB Stem is lightweight and durable. The original setup in the shoulders, arms, and back had to be corrected to achieve a more comfortable riding position. The stem and riser handlebar allow you to sit upright on the bike, which is better for your back. The bicycle stem should be connected to the front fork stem. The four bolt bar is in position. The bicycle stem is easy to install. The four bolt bar is in position. The Boenoea bar stem is suitable for most road bikes.
👤An earlier review has been updated. Customer service was very helpful. I mistakenly ordered the wrong product. Excellent service and product. Buy with confidence.
👤It was perfect for our bikes and made them more comfortable to ride. We don't have to say anything over here.
👤On my first Mountain Bike Ride, I had this stem rotation all the way to its highest position, and then 3 miles into my morning ride, while going down a steep hill, this extension rotating all the way forward caused me to lose control of my steering. I didn't get hurt. I had a small tool kit with me, so I had the correct size allen wrench to retighten this down, but I didn't tighten it correctly in the first place, but then it loosened again within 2 miles. I'm not weakling. I'm 6'2” and weigh 230 lbs, and can bench press 300 lbs, so I'm strong enough to tighten this up. My words of advice are very dangerous. Don't buy.
👤I switched to straight bars and this riser stem because of my back. The mission was accomplished. I would have preferred a fixed stem with the same dimensions, but couldn't find one.
👤The top of the steerer tube is exposed and the cap is not flush with it. It will work, but it looks cheap and horrible. It should be sent back for something that works.
👤This worked well with the Jones handlebars to convert my E MTB to an upright cruiser. I swapped out my seat for a saddle and grips. There is a A well made product.
👤The stem is good for the price. I wouldn't recommend this for a mountain bike track that is very rough due to the possibility of the stem being loose enough to let the teeth that hold the stem angle fall down. It's great for biking.
👤The quality for the price is excellent.
👤I have health issues and need a more upright seating position and different hand positions. I ride most of the time in the city. The gravel bike has a lot of things that make it good, such as its speed, s position, handlebars, tires and ride. The stem was expected to creak and flex going uphill. I do it on my hybrid all the time, but I don't have the confidence to go downhill at speed. I get the feeling that the unit will fail because of the play. Maybe I got a bad one. The position is perfect. Can't come back. The 90mm stem is fixed.
👤I own three bikes with this item on them. It allows a wide range of handle bar height and position to make riding more comfortable. I prefer a more upright position. This makes smaller bikes feel more comfortable. This is a good investment that can be used for later machines.
👤Works well with my bike. I can adjust the height easily with the right size. The quality is excellent. Installation was fine, but I had to put it upside down the first time. Make sure the text on the unit is correct. You will be fine!
CYCLING COMFORTABLY: Handling more flexible, much easier to force when climbing, lighter weight, comfortable and convenient to operate, effective bicycle fork extender. The diameter of the tube is 28.6mm (1-1/8"), the handlebar is 31.8mm (1-1/4"), and the length is 90mm. It is adjusted. Light weight, hollow design. Please make sure you confirm your size before purchasing. The four bolt bar is in position. Simply connect the original fork stem to the new one. A universal short handle bar stem is suitable for most bikes.
👤I have an issue with my own and I am subtracting one star. I was impressed with the quality of the unit. I tightened the locking screw after adjusting to the desired angle and noticed there was still movement at the joint. I tried to tighten the screw but it wouldn't tighten and the joint was still loose. When the screw is tightened, the joints have teeth that mesh, but in my case they were not fully meshing. I noticed the problem after removing the screw completely. When you loosen the screw, the spring inside pushes the joint ends apart. The spring in mine was too long and was being fully compressed when the screw was tightened. I used a pair of diagonal cutters to cut off the spring length. The joint is locked solid with no movement even with only moderate tightening of the screw. I noticed that people who had this issue broke the unit or stripped the screw trying to tighten the joint not realizing it was the spring inside the joint causing the problem. I hope this will help other people. There is a The bike is much more comfortable to ride after this was installed on my bike, and I like it because I can adjust the handlebars up to a better position.
👤I am a tall person, as stated in my review. I bought a new bicycle to replace a bicycle that was 10 years old. The seat of the bicycle will be extended significantly if I need a XXL bicycle. I was putting a lot of weight on my hands because the handlebars were low. My hands became numb after a few miles. I reversed the bicycle stem to point upward because the store installed it for aggressive riding. This made a difference. Most of the bicycle stems I looked for were fixed. When I saw that it had positive teeth engagement, I found this one. I decided to try it. I tried a 30 degree adjustment and ended up at the 60 degree adjustment. I like this better than an extension because it doesn't increase the moment and stresses in the bicycle stem. I can now ride 20 miles with no hands going numb.
👤I'm very pleased with my purchase of the Wake MTB varaiable stem. I was a little worried about the quality for the price. I'm happy to report that these feel just as good as any big name brand stem. The variable geometry will be useful on my hybrid road conversion project. I was worried if one could get the pivot bolt tight enough to keep the stem from moving. When you hit something. This was a non-issue. The inner part of the linkage is called a rosette surface. A bunch of "V's". It doesn't budge once it's tightened down. * 5 Stars: Works exactly as advertised, fit/finish are what you'd expect when purchasing this type of product, and it is a good value, 4 Stars: Works exactly as advertised, fit/finish are what you'd expect when purchasing this type of product, and it is I'd change a few things, 2 Stars: Barely works but can be made useful if you try, and 1 Star: Useless, does not perform it's intended function, and is generally a waste of money.
Bicycle neck stem products from Fomtor. In this article about bicycle neck stem you can see why people choose the product. Fomtor and Profile Designs are also good brands to look for when you are finding bicycle neck stem.
Fomtor, Fomtor and Profile Designs are some of the best brands that chosen by people for bicycle neck stem. Find the detail in this article. Fito, Yuauy and Fomtor are also brands that their products are worth to check.