It's suitable for most road bike, mountain bike, track bike, BMX, etc. The stem is only suitable for 25.4mm handlebars. It is adjusted. The product equip with 5 gaskets can increase the height up to 100mm, it can adjust the gasket to fit your need freely, reducing the pressure of waist effectively. The bike handlebar riser is made of aluminum and has a polished finish. It's widely comparable. Don't worry about buying a bike accessory that isn't compatible with your bike. Their bike fork stem extension is suitable for most bikes. Easy installation. You can connect the original front fork stem extender. Light weight and flexibility make it easier to force when climbing. It is hard to loose the handlebar extender. Work on mountain bikes, road bikes, and BMX.
👤The handlebars of my bike were lower than my bike seat. If I rode the bike as a road bike, I would have hybrid tires for off-road biking. The Zukka extender was easy to install, using up all 5 included rings and the 3 that came with my bike. All fit perfectly. Make sure you use an Allen key to tighten things up. The perfect ride resulted in no back pain from straining my arms and upper body.
👤I can sit upright on my bike. Solid construction. The pinch bolts of the riser and stem need to be snug to be able to move. Align everything and hold while you tighten the top bolt to eliminate any play in the headset bearings. The inside of the riser has bottomed out on the top of the steering tube, so if you find it is taking excessive Torque to eliminate this play, it's because the inside of the riser has bottomed out on the top of the steering tube. Put a short spacer under the riser.
👤I'm a big guy with 220 lbs and found myself hunched over when riding. The stem extender brought my handle bars up so I can ride in a better position and it looks great.
👤The expectations were met. Good length. If you don't use the full length, the excess will stick up from the handlebars, which is a possible safety issue. First you have to figure out what riser length you need, then you have to buy it.
👤It was a noticeable difference on the first day. I had groin, back, and next pain after riding so far forward. A guy with a bike. I also want to give up my bike. Win! It's easy to install. Looks great! I'm hoping this less than$15 item will make me happy after biking days. The game is changing now! Simple concept is great.
👤I was able to ride my new mountain bike with less pressure on my hands and wrists, because the handlebars were raised with this extender. LA gave a tip on excessive play in the front fork from the riser extender bottoming out on the top of the steering tube after its initial installation. LA's tip was to place a second spacer on the steering tube below the riser extender to raise it slightly and then tighten it down to eliminate the play in the front fork.
👤The bike handle was made higher by this extender. I'm happy my husband found it. We ordered one for our daughter's bike as well. It was easy to install. It's much more comfortable to ride a bike now. You'll be fine ordering this extender.
👤Lifted my handlebars. I'm really pleased with this purchase because I was sitting for a long time. Sturdy metal, and fit my bike well. The bikes brand is Specialized.
The fork Clamp has a diameter of 22.2 MM. The front fork stem diameter is 28.6mm (1-1/8") and the Handlebar diameter is 31.8mm (1.25''). The angle is 0 90. The height extension is 140mm. Help to make your bike comfortable. It is made of high- strength and durable aluminum. The weight is 304g. Measure your handlebar diameter before you buy this stem. It's easy to connect up the original fork stem. Two bolts hold the bar in position.
👤The stem makes the handlebars closer to the rider for a more upright riding position. The stems that are adjusted in the front of the steerer are better. There is a The stem is heavier than I had expected. There are two adjustments needed for the adjustment to be simpler. Maybe the two adjustment provides a more secure lock? There is a The poor design is in the steerer, where the top of the slit is connected, so it doesn't allow a free/natural clamping. The pictures don't show the section of the stem. There is a The difference between the top and the bottom of the clamps can be seen in my uploaded picture. The top part cannot be fully tightened because the adjacent part is strong.
👤I have back problems. The stem is perfect for adjusting my position. It was easy to install and I was able to set the perfect angle for riding. If you want the stem to be close to 90 degrees, be aware of the length of your cables for brakes and controllers on your bike. They may not be long enough to raise the stem that high. This stem is recommended. Great product.
👤I'm a long time rider and my bars are no longer comfortable. The bars can be adjusted to raise and bring them closer to me. It's clear that this item gives me plenty of range in three dimensions, even though I'm still working on the final fit.
👤It's pretty nice. The handle bars were low and the new stem raised them up a bit. There is a I will not hunch over. There is a I can ride my bike for longer. There is a It is nice to have the option to change the angles of the stem.
👤I needed a new bike and the stores were sold out due to the Pandemic. The angle of the handlebars made it very uncomfortable for me. The stem was installed in about 20 minutes. It was very easy to install, and the ride is now very comfortable. Very happy with the product!
👤The device raises my handlebars and makes it more comfortable to ride. The plug that goes in the hole on top of the post is easy to remove. I lost my ride. It's not a part you really need.
👤My mountain bike style ebike was converted to a hybrid style ebike. Installation takes less than 30 minutes and is easy to ride. The quality is decent. Changed my opinion of the bike.
👤I needed a bike stem that would allow me to sit upright on my road bike after having spine surgery. I was able to position my handlebars at 0o straight upwards thanks to this device.
👤The ideal component for a more comfortable ride.
There are 4 sizes of bike handlebar spacers in this package. Each size provides a combination to adjust the height of the handlebars to fit your riding style. Bicycle headset spacers threadless are made of black anodized aluminum alloy material with smooth surface and exquisite workmanship, eco-friendly, sturdy and durable to use. Stem spacers road bike inner diameter is 28.6mm, 1-1/8" headset set, compatible with 28.6mm front stem fork of mountain bike, road bike etc. There is a feature. The aluminum headset spacer is more sturdy and resistant to damage than carbon fiber headset spacers, and it's 888-282-0465. If you go for a heavy duty off road ride, you should use aluminum spacers other than carbon, due to automatic cutting, smooth edge, and fit most of the road bicycles.
👤The stems on the two bikes I changed had 3 x 10mm spacers on them. I didn't know how I would position the spacers, and I didn't know the exact measurement of the bike's bar height. The kit was perfect. I used this product above the stem to place 20mm below and 7mm above. The other placee is 20mm + 4mm. These are an excellent value, and work exactly as I had homes. If I make changes again to this bike or others, I am set.
👤These work well, but they aren't as thick as the factory spacers on my or my son's bikes. It's a good value for the price and the selection of spacers. It's very easy to get the correct rise to allow for the 3mm gap between the steerer tube and the cap.
👤The image in the listing does not match what is in the description. There are three different types of spacers in the photo. The spacers they ship are 2, 3, and 10mm. When they arrive, you will be disappointed if you go off the photo.
👤The new handle bar was what I needed. I didn't think about needing spacers when I ordered the bike stem. I ordered this set and it arrived very quickly. It was nice to have different types of spacers.
👤These seem to work well and match the other ones on my Trek. I have had one of the spacers on my bike for a month and so far no issues. Will keep you updated if something changes.
👤The spacers were smooth with no burs and consistent sizes. There are 12 different sizes of the bag. You could buy a couple at the store. These are nice to have around.
👤There are 12 pieces for the price of 2. Good quality. I like aluminum more than carbon fiber. These mountain bikes will not fail because I can be hard on them. The handle bar height can be a problem if you don't have a good selection of sizes. For the next project, spare.
👤It worked out as planned. Good quality. There were no problems. Take accurate measurements.
👤This is a good set. The set has enough pieces to adjust more than one bike. They are lightweight and durable. The price was good and the shipping was fast, which was a plus.
👤Needed to install a new bike stem. There are lots of different sizes of Qurans.
👤There were different sizes of spacers. Excellent quality. They do what they're supposed to do. The product was good and the seller did a good job with it.
👤Good quality work.
What you will get. The length is 115mm or 180mm. There are 6 gaskets, 2 x 20mm, 3 x 10mm, and 1 x 5mm. 2. There are 2 gaskets, 1 x 10mm, and 1 x 5mm. You can adjust the gasket to fit your own height. The diameter of the tube is 28.6mm (1-1/8"), the handlebar is 31.8mm (1-1/4"), and the length is 90mm. Light weight design. The four bolt bar is in position. Simply connect the original fork stem to the new one. A universal short handle bar stem is suitable for most bikes.
👤It weighs 7.68 ounces and is definitely not T6 aluminum. It's not sure what it's made of. It could just snap in two with enough stress. Seeing that this is being used as a mountain bike part, it will be easy to see how much is needed to snap it. I will be asking for a full refund and throwing this in the trash. I am used to a certain level of testing and certification for products like this to make sure I am safe on the trail. This is concerning to me. "There is no consumer protection when products are sold on Amazon". Consumer protection also covers my safety and yours as well. I don't know if Amazon cares.
👤This is not a 90mm stem. I attached a diagram of how stems are measured, and it measures 105mm in that dimensions. It has a 45 degree angle. The measurement center is 74mm. I replaced a 70mm 7-degree steam and it increased the Reach just 2mm. Keeping Reach is important since moving the handlebars further away makes you lean over more, even if the handlebars are higher, and too little reach can lead to instability or twitchy steering. The part that is used to hold the steerer rube is over 2 feet tall. This is taller than many other stems, which is a good thing since it will reduce strain on the steerer tube. It means you'll probably need a lower space stack height because you don't want the top of the stem too far above the steerer tube. My handlebars were raised 35mm while I changed the reach to just 2mm. It should be perfect. The other stem on Amazon looks to be the same, but it comes in both 45 and 40 degree angles. This one is the same price as the other one. That one appears to have the same mistake. There is a If you want a brand for safety, the best one I could find is this Ritchey: https://www.amazon.com/Ritchey-Comp-4-Axis-Stem-Degree/dp/B07VYKZ38W It's only 30 degrees, but comes in various lengths. The "comp" version is only 80mm in length. There is a If the Wake stem is marked as 3D forged, it would be a good sign of strength. It's hard to believe that the weight and price are so high.
👤I wanted a more upright riding position on my trail bike in order to see what was going on around me. I thought moving my hands back and up around 50mm would do the trick. I was looking for a set of handlebars that would give me the rise and sweep I was looking for. Some handlebar sellers don't give specific dimensions for the bars they sell. I thought about replacing the stem because of the cost and the quality of bars. The Wake stem is 90mm long with a 45 degree rise, which is the same length as the old stem. My hands are now about 2 1/2 inches further back and about 2 inches higher than before, because I used the same flat bar on the bike. It was perfect for what I wanted and a better posture for trails. The product is well made and finished, with thicker tube walls and a taller steering tube collar than the stem it replaced. Only marginally heavier, and beefier. It is easier to swap out a stem than it is to swap out a bar. The low end bars are $30-50. It's easier to determine how the new product will affect your ergonomics.
The safety is certified by the EN. Can't get comfortable on your bike? Did you try too many bike stems? For touring where you spend a lot of time in the saddle, this is a useful way of adjusting your handlebars height and reach. The best bet to get comfortable is their stem. Only fit for Handlebar diameter 31.8mm (1-1/4''), front fork stem diameter 28.6mm (1-1/8") and is available in a range of lengths. Before purchasing, please confirm your size. The material is. The 3D forged alloy construction of the MTB stem gives it strength and control. The stem is very durable with an angle of 70. It's easy to connect up the original fork stem. The four bolt bar is in position. It's suitable for most bikes. Their bike stems can be used for a wide variety of bikes. It's ideal for people who take off road biking very seriously.
👤This is a nice stem. It's tight and easy to adjust. It has bigger 5mm bolts than the smaller 4mm bolts that are used. The cheap Chinese risers I had had so much slop in it, the handle bars were rocking back and forth. I couldn't get it out. This one looks more expensive than it is. The rise degree indicator is accurate. The quality of some of the "name brand" risers is probably the same. All of it was made in China.
👤I put this on my Fatboy to raise my handlebars. There is a The unit looks amazing, matches the bike's finish very well and has a very solid feel to it. I'm a new bike maintenance person, but I recommend that the handlebars be screwed on during the installation process. The screw holes didn't line up exactly when I attached the handlebars, because I removed that immediately. Less than half a millimeter off. I loosened the angle adjustment screw and took some plastic wedges between the sides to allow me to secure it with screws again. I like how it turned out. If I want to go back to the trails, it is totally changeable.
👤The hassle of changing everything over on new handlebars was thrown into the mix when these brought my stock handlebars up 4 inches. Everything was kept tight. The length is 5 1/2 ". The stock stem was 1 1/2 inches.
👤The handlebars had to come up to relieve the pressure on my hands. The riser helped a lot. No issues so far. I put butterfly bars on this bike. What a change! The bars and riser worked well together. The best bike mod I have ever done. This riser gave me a lot of options and angles to work with.
👤After 3 tries, this one actually fits real mountain bike bars. The only downside is that you will need an extra spacer to make the neck fit the stem and be tightened from the top properly. I had one laying on the floor. If you plan on using this neck, I would recommend buying some. Thank you.
👤It was easy to install on the gray Vista bike. I wish I didn't have to return the bike because of the poor transportation. The steam would make the bike look better and more comfortable.
👤I used this to increase the height of my handlebars. It worked out great. It is easy to assemble. You should know the diameter of the handle bars. Originally purchased for my wife. She had 1” in diameter.
Also available in silver. Please search for the ASIN number "B00ATT6TSO". Only fit for handlebar and steerer tube diameter Before ordering, please read the Purchase Guide. The degree is adjusted to 0-60. It's not applicable to Giant bicycles. The mountain bike stem is made of high strength aluminum. The MTB Stem is lightweight and durable. The original setup in the shoulders, arms, and back had to be corrected to achieve a more comfortable riding position. The stem and riser handlebar allow you to sit upright on the bike, which is better for your back. The bicycle stem should be connected to the front fork stem. The four bolt bar is in position. The bicycle stem is easy to install. The four bolt bar is in position. The Boenoea bar stem is suitable for most road bikes.
👤My old Gary Fisher Tasahara mountain bike has a design that makes it difficult to bend over. It was no longer enjoyable to ride as I got older. The ebike conversion kit has changed that. The handle bars were raised so I could ride less bent over. It is much more comfortable. I don't ride a lot, but this has held up well so far.
👤The item arrived on time. It was easy to install and it made a difference on the height of the handle bars. If you want to do more aggressive riding, you can adjust the height and raise it if you want. There is a The product looks like it was made from high quality material. Before I installed the extender, I took two pictures. There is a I ordered a set for my bike and a set for my girlfriends bike. The extender was a perfect fit for my bike. I had to order some spacers to fit my girlfriend's bike. It was an easy fix. There is a I am satisfied with this item and would recommend it.
👤I needed a more comfortable position for the bike I use indoors in the winter. It was easy to install. It is not as stable as the Thomson stem, but it will work great on my trainer. For mountain biking, I will put a solid, non-adjusting stem back on the bike.
👤I needed to raise my bars. It's easy to install. I might go to a solid neck at some point. I was able to dial in the best position for my bars. The bars are in place. There were no problems.
👤I had to return my bike because it was not the right size. I would have liked the design and the rise to my handlebars, which are a little low, if it had been the correct fit. It would be a great product if it fits your bike.
👤It was easy to install and adjust the stem. The process took 10 minutes. I had to get my old stem off because some of the bolts were rusty. I put this on my trainer bike to raise the handlebars. Highly recommended!
👤Adding this to my mountain bike allowed me to sit more upright and it reduced wrist soreness. It increased the height of the arm position by about 4 inches. I can't testify about its resilience since I don't jump or do tricks. It all stays snug without a problem.
👤I'm converting my older street bike to one with a front brake caliper, so I need a new headset. The Sanzhi stem has nice features and will make you feel more comfortable.
The original setup in the shoulders, arms, and back had to be corrected to achieve a more comfortable riding position. The stem and riser handlebar allow you to sit upright on the bike, which is better for your back. Only fit for Handlebar diameter 31.8mm, front fork stem diameter 28.6mm, and Length: 90mm. The angle is 0 90. The height extension is 135mm. Help to make your bike comfortable. The weight is made of high-strength, high-quality aluminum. It's suitable for most of the mountain bike. Measure your handlebars before you buy them. It's easy to install. The easiest way to adjust the angles is to loosen the bottom screws with a wrench and take out the black buttom.
👤It was fairly easy to install. The screws that lock the stem into the desired angle were so tight that it was impossible to loosen them. The Torque must have been much higher than what was needed. Returned and bought a different one.
👤The company/seller was very accommodating and offered a refund for my troubles. I am not a fan of the product, but the seller stands behind it and that is commendable. There is a This is a poor purchase because of the screws and directions. The soft screws are very easy to strip, which is completely unacceptable when dealing with bicycles. The installation is hard to understand. I need to purchase a stripped screw removal kit or I won't know how to remove this from my bike. I don't think a product like this should be sold without screws that can hold up to the stresses of several installations.
👤The side adjustments screws are soft. The screws were so tight that they wouldn't loosen up even with a bar. Couldn't raise it up. I stripped one of the screws. The money was wasted.
👤I've tried 2 and one of the side adjustment screws could not be loosened. My new part won't be here until March after I return the second one for a direct replacement. Either they have back burnered me, or they are fixing the production of the part before sending me again. I will update when I know.
👤I don't like bikes. I bought an REI Co-Op hybrid for casual riding. I could no longer tolerate the setup after a month. I bought this stem to improve the riding experience. I chose this product for two reasons; good reviews and the fact that I didn't know what I was buying. There is a It was easy to install. It is very easy to assemble onto the bike. The product is very well made and it fits perfectly. There is a It made my ok rider happy to ride. I am glad I bought this. Highly recommended.
👤I found it hard to adjust. My solution was to remove the two pieces. I reassembled after applying grease and sanding the exposed metal sides. It works now. A nicely engineer product is followed by poor manufacturing.
👤I needed an extension for my bike. I was able to install it myself after it was mentioned in the Facebook group.
👤I wanted to relax in my riding position. This is a solid product that will allow you to adjust the handlebars to accommodate different riding positions. Installation is easy and no instructions are required. Gave my hybrid bike a new lease on life by taking some of the pressure off my neck and shoulders.
👤It was bought to help with a shoulder injury. It took 3 weeks for it to arrive. I received a stem that was missing 2 bolts and was clearly used. The icing on the cake is useless, as other reviews say. I should have known better than to buy cheap trash.
A universal short handle bar stem is suitable for most bikes. The bike handlebar riser is made of high strength aluminum alloy. Very strong and resistant to rust. The height of the product can be increased by up to 85mm with the use of 4 gaskets. The gasket can be adjusted to fit your needs, reducing the pressure of your waist. Don't worry about it won't fit your bike. The fork rod extender is suitable for most bicycles. Mountain bike, road bike, BMX, etc. Simply connect the original fork stem extender. Lighter weight, easier climbing force. More flexible handling, light weight, easier climbing force, comfortable operation, convenient bicycle fork extender are some of the things that make cycling comfortable.
👤I bought these for my kids' bikes. They were able to match their frames. There is a The seat stems are long enough to raise but not the handlebars. I was able to install the two different sizes of allen wrench in about 5 minutes. There were no problems with stripping or anything like that.
👤Simple and inexpensive. I have been using the stem extender for a month. It's been great.
👤I bought this to raise the handlebars when using my cyclo cross bike on a trainer. The normal riding position is great for IRL, but the trainer makes my shoulders hurt. It only takes a few minutes to get those handlebars up for winter training. I had to unwound bar tape to get the slack in my cable.
👤I should have installed this on my bike a long time ago. I had never experienced that level of comfort on this bike. It was easy to install and a good value.
👤I put it on her bike. She upgraded to a 24" bike a year ago and was already complaining that her handlebars were too low. They grow fast. She will get at least another year out of it now that she put this on.
👤A lot of bikes have handlebars that are too low. It's easier to ride the bike now that it's raised. Thaks.
👤The extender was easy to install. It provided a more upright sitting position.
👤It makes a huge improvement in the level of comfort. The neck and shoulder pain that would normally happen would not happen.
A universal short handle bar stem is suitable for most bikes. The maximum height extension is 70mm. There are 4 spacers, 1 x 10mm and 3 x 5mm. The height can be increased up to 70mm. Simply connect the original front fork stem to the new one. Light weight. It is made of high-strength T6 aluminum alloy. Handling more flexible, light weight, easier to force is comfortable. It's suitable for 1-1/8" 28.6mm Fork Mountain Bike, Road bike, Track bike, Folding bike, MTB BMX...
👤The stem riser extender worked well. Before this extender, I could have raised my seat to the proper height for my legs, or I could have put my seat too low for my legs, with good upper body posture. The performance of the extender is good. The bolts are smaller than the original neck bolts. I gave the extender 5 stars because they are holding. I will look for an extension with beefier bolts if they fail. Installation took longer than expected, but not because of the product. The nut in my stem was a little crooked, but it wasn't noticeable on the short bolt. I wonder if those people had a crooked stem nut assembly like me, because I read a number of reviews that the long bolt was bent. The graphic I attached shows what I found. I lightly tapped the head of the bolt with my finger to make sure the stem nut was straight. The stem bolt on my bike is held in place by 2 star shaped pieces of steel. It was not very precise, but easily straightened. The long bolt worked perfectly when the nut was straightened.
👤The stock steer tube on the 2012 Trek 3500 was too low for the current rider, and the handlebars were too low for the original 2012 Trek 3500. Those in need of an elevated handlebar need a stem extender. There is a The FOMTOR stem extender is an excellent quality aftermarket bike doodad. It has nearly four inches of vertical position. It includes a long titanium bolt to reach the distant star nut, six aluminum spacer rings, and a matching cap. There is a The FOMTOR stem extender was perfect for the existing steer tube. The titanium stem bolt is stout enough to hold the entire headset in place, and appears to resist dynamic loads and stresses under normal use. Black powder coat finish is what the stem extender, cap, and spacer rings are made of. There is a It's annnnnd... I bought the last one on Amazon. I need two more.
👤I used these for my bike. It made a huge difference in my riding position. The height to the bikes handle bars was increased by the spacers. I liked that it was all plain black and not colored. The end was very clean.
👤The bent bolt makes it hard to install with the new cap. The stock cap is not centered because it was not used without the recess. The bolt would be 5 stars if it wasn't bent.
👤It was my fault that I didn't double check the measurements for the bike I am fixing up. I won't be returning it because I am hopeful it will fit on another family member's bike. I was sad it didn't fit on my body, but it looks like it's very high quality. Will update this review if it works for the other bike.
👤The extender tightens down when it connects to my fork tube. I had the right amount of spacers and the extender fit my new stem perfectly. I am happy with my purchase and would purchase again.
Handling more flexible, light weight is easier to do. 1. The maximum height extension is 180mm. There are 6 gaskets, 2 x 20mm, 3 x 10mm, and 1 x 5mm. You can adjust the gasket to fit your height. 2. Simply connect the original front fork stem to the new one. 3. The forged aluminum material has a polished anodized finish. 4. It is suitable for most bike with threadless headset. 5. Handling more flexible, light weight is easier to do.
👤The spouse and I took the bikes out today. It was noticeable that there was no wrist, hand, shoulder, or back pain after about 14-16 miles. I might even buy a stem that can be adjusted to fit my body, and maybe even buy upright grips, since I am going to try some more rides. The benefits are well worth the minimal cost of experimentation. Do you want to come back from a long ride achy or do you prefer to spend money and make your ride comfortable? There is a The product arrived in two days. I had looked for videos on the internet before the event. Installation was not good. It took about 10 minutes. I bought two of these for my spouse and myself because I had just bought two e bikes for them. The handle bars on the bikes were too low and caused us both to lean too far forward which resulted in wrist, hand, shoulder and back pain. The ride is much more comfortable now that I raised the bars up. If you have a mountain bike, you might want to consider one of these.
👤This is what I needed to stop my hands from feeling numb. It wasn't too long for me. The handlebars were the same height as my seat when I adjusted the pedals, but I'm 6'2” and on a large frame fat-bike. The poor geometry was fixed by this. There is a It's very sturdy with no creaking. I weigh over 300 lbs. It holds up well with me. I'm very happy with it.
👤This product does what I need it to. I can ride without hunching over. There is a There is one thing to note. The front brake line has a limited amount of slack, so it is a good idea to buy a much longer brake line or cable. The item allows for a big change to the handlebars.
👤Awesome. It doesn't raise the handlebars to the max. The total length of this product is that. It doesn't take into account that you have to use about 50mm or 2 to bolt it on. It's about 130mm or 5. It's still great. If you need more, put some above. It would stick up 130mm. I think you could remove the top spacers and cut the bolt if that bothered you.
👤I am happy that it raised my handlebars. I needed extra ones, so I had the previous one. It was fine. I didn't try to tighten it. It comes with a spider, a spider web, pumpkin, and a white cloud, but the rest didn't make sense to me. Someone in the comments or question area noted the same thing and wanted to remove the decals. I used cotton pads to apply finger nail polish. I removed the top layer, but you can still see the white over the black ground. I am going to use a tooth brush and fingernail polish this week. I think I can get it all off. I am happy with my purchase. I bought another extender a month earlier, which was about 2.75 inches shorter than this one, and it was good. When I bought this one, I had to replace all my cables because my old ones became too short, and I couldn't get my brake and shift levers back onto my handlebars. I bought Jagwire cables that are longer. I had to buy new housing and cable for both the brakes and shift, and each cost me about $30 or $35. I watched a video on how to adjust a front and rear derailleur. I would recommend buying the orange Klunker Commuter Urban Bicycle Handlebar and the Champ Oversized Comfort Bike Seat. I can ride a 25 mile ride now that I can sit up straight.
The handlebars have a diameter of 25.4mm. Please confirm your bike's diameter before you place your order. The item isn't suitable for your bike. The bike stem is sturdy, well designed and easily adjusted, which is preferable to removing the handlebar stem and exchanging it for one with a different angle. The installation is easy because the specifications are accurate. There is a degree of angle indicator on the adjacent parts. You can see where the handle bar is positioned with the opening on the stem. This is a nice riser. The thickness of your handlebars may affect the installation of a shim. If the threads loosen up, be sure to use glue on them. The original setup in the shoulders, arms, and back had to be corrected to achieve a more comfortable riding position. The stem and riser handlebar allow you to sit upright on the bike, which is better for your back.
👤Went with this stem because of the reviews on the internet. It was on time and there was no damage. The stem is very strong. It looks like a piece of equipment from an original equipment manufacturer. I threw away the instructions and proceeded to install the stem backwards, since there is a degree of angle indicator on the adjacent parts. Loctite was used on all the parts. It has about 400 miles on it and everything is holding up. My Cannondale Quick 1 hybrid was raised to the perfect height. As I raised the bar, I had to change my attachment points downward. Allen head bolts are used so no phillips heads are used here. One suggestion would be to put a small line in the center of your handle bar so you can keep it centered as you install. You can see where the handle bar is positioned with the opening on the stem.
👤This was installed very quickly with a 4mm and 5mm wrench. You can see from my photos that it raised my handlebars up and pulled them closer to me, about an inch in each direction. My old stem was too long and too low for my comfort, and it set my drop handlebars too long and too low. Riding put a lot of pressure on my wrists and heels and it was also causing pain in my shoulders when I rode. The solution to that problem! The piece is strong. It's very stable because of good quality and construction, and because the screws are tightened down properly. I don't think it would detach from the bike. If you need to raise your handlebars, it's highly recommended.
👤I ordered it for use on my bike. After receiving this, I learned that the stems on mountain bikes shouldn't be adjusted. Put it on my wife's bike. The part looks good. It is easy to install. I would suggest that those who don't carry pocket wrenches do so when they have this installed. There is a chance that a bolt can loosen. Wouldn't want that to happen on the road. I have nothing but good things to say about this part and most bikes. I think mountain bikes are not a good addition due to the risks and rough trail impacts.
👤If you've never worked on a bike stem before, you should look at the stem spacers advertised in Amazon's "you may also want..." section. If you find that the riser extender's base isn't as tall as the one you're replacing, you'll need some 1-1/8" aluminum spacers to tighten your stem back up. Now is the time to order 'em. I'm waiting for Amazon shipment #2 to arrive. I have not used the riser extender, but it feels solid. If I don't experience anything else than joy, I will update this review.
👤I like to be as aerodynamic as possible on my main road bike, but my geometry is different on my commuter bike, so I need to change. It made a world of difference when this was added. A heavy backpack makes the ride much more comfortable. I can adjust and change the angle. Make sure you have enough play in your cables for the change, or you may need to rerun some cables. I had to reduce how high I increased the angle, but it still made a big difference. I'll just run it at the current angle until the next time I need to change the cables. The part is so good that you don't need to get one with another angle.
Bicycle neck riser products from Zukka. In this article about bicycle neck riser you can see why people choose the product. Fomtor and Gooday are also good brands to look for when you are finding bicycle neck riser.
Zukka, Fomtor and Gooday are some of the best brands that chosen by people for bicycle neck riser. Find the detail in this article. Wake, Cxwxc and Sanzhi are also brands that their products are worth to check.