The center to center spacing between the pins is approximately 7/16" wide. The engine is the 100CC. They used a generic version of the user manual for 80CC/100CC because they look similar. It comes with all the necessary hardware for easy installation. Heavy duty metal engine body. The max.speed was 48 km/h. Fuel type : 90#; N.W: 11 kilogram; G.W: 12 kilogram. It's for most 26" and 28" bikes. The frame should have clearance between the bottom brackets and the top bar of 9-11mm, and the diameter of the frame tubes should be 25-28mm. 50mm bore single piece cylinder, an upgraded CDI, Performance Speed Carburetor and more, high performance Speed Carburetor, silver anti-corrosion coating, high performance CDI with Yamaha components, improved magneto, high end allen bolts, improved gas cap. The mixing ratio for fuel and oil is good for the first 300-500 miles, but it is not good in the summer because of the hot weather. Please limit the riding time to a maximum of 1 hour for the first few rides to avoid any problems with the motor. If you have a question or are not satisfied with the product, please contact them. You can find the order by going to your account at Amazon. Click the seller name to enter the store page. Click "Ask a question".
👤The bt 100 engine kit is uncommon to fine one of these engines. There are a few issues with the bt 100 engine kit. The magnet seems to be weak on one side. If I am able to find a replacement, I will have to.
👤It was a great way to get back and forth from work. It was amazing to feel that kind of power on a light frame bicycle. I added a 36 tooth sprocket and it definitely increased speed. It went from 30 mph to 35. I added a air filter and rubber motor mounts to make the motor less vibrate. All in a great product. It is very easy to put together.
👤The motor kit is great and there have been no issues so far. It's worth $200, but not if the exhaust isn't able to upgrade or change, my buddy built it for me and you can contact him on his Facebook page called - New motor bike builders.
👤They changed the engines. Either that or they have a few different ones. I have no issues with the motor. The chain was changed to a two bolt because I didn't use them enough. There is a great engine with lots of power.
👤I built and bought many engines because I use them for my food delivery job for two years now. The engine and accessories are the best yet. The bigger and better design of the carb makes it non-standard. If you buy a 100cc engine from bike berry, they will send the other ones. If you tighten the studs all the way in, they are not long enough to put bolts on. The other accessories were all of the same quality, and it looked like this guy took the time to package them. One thing I like about it is that the head came assembled, everyone else started making the customer do it, which is a pain in the ass. I just connected it to the bike. I learned that you have to be careful with the journal bearings, there is only a small film for them to ride on, and 3cc of oil in the crankcase, on my last 100cc from bike berry. Don't accelerate down hills when the engine is not running. I'll never find a 2 cycle engine that will get more than 5000 dollars worth of food deliveries done, but I will update when this engine takes a bad turn. It was an edited version. The motor took a bad hit on me. It has been 3 or 4 months of hard work delivering food. This engine has made me more money than any other. It was probably my fault since I forgot to put oil in my car before I left the gas station. It can happen in a few seconds if the circumstances add up. My mind is against me, and it's been so long since my back tire or my engine had ruined my day that it had to intervine! What an ass! I watched the destruction of the engines. I bought an extra one, I will be much more cautious and get an accurate picture of how much better this engine is than the rest.
The product has a 12 months warranty. Please contact them first if you have any questions. They can help you find a solution. The perfect bicycle tool set is fully equipped. Most of the tools are in it. There are bike chain plier, bottom brachet wrench, bike chain whip, etc. You don't have to buy them separately. Meet your daily repair needs. Your bike is in great shape. The bicycle maintenance kit is durable enough to repair tires, brakes, lights and chains. It is also suitable for simple car and home maintenance. It's a must-have for repairmen and construction workers. All tools are made of heat-treated carbon steel, which is anti-corrosion and anti-rust. The rubber material is eco-friendly. It guarantees your safety and comfortable use while prolonging the service life. The bicycle repair tool kit is from the 24 Portee. A chain rivet extractor, a chain ring nut wrench, a Crank puller, a Freewheel turner&lock ring wrench, and a Bottom brachet wrench are included. A tire patch kit, a lockring removal tool, and a flat/phillip screwdriver are included. You can organize your tools with a toolbox. It's easy to store and carry. This set of tools will make your job easier.
👤My purpose in buying this set was to have essential tools for mountain bike repairs. One would think that the set would have a basic description of what was purchased and the best way to use, but nothing. Half of the tools in the set would last for a long time. The chain tool broke on my first project. This isn't a set of specialized biking tools. I'll put it in the truck and look for a shop set. I was hoping that I wouldn't have to spend that much. I am reminded that I pay for what I get.
👤Es un kit decente, sin embargo the troncha cadenas de mala calidad.
👤The bike kit is a good choice for a new bike owner. I use this to repair my bike because there is no bike repair center near where I live. It is very cheap and easy to use compared to sending my bike for repair.
👤Chinese made tools are very low quality. I spent the extra money on a single kit for basic maintenance. I had to borrow other tools from a neighbor to perform simple tasks because I had to modify the chain tool. I would spend money on park tools.
👤Woow. It is a very good tool. If you own a bike, you should have a tools kit. Very nice quality and easy to use.
👤Hecha con materiales de poca calidad. Herramientas. Y menor.
👤The nut with the end is useless. The opening is too small and the wrench won't fit over it.
👤A great vacation kit. Can do everything you need to.
The product has a 12 months warranty. Please contact them first if you have any questions. They can help you solve the problem. The chain is heavy duty. Fitment for 2 stroke 49cc. 60cc 66cc 80cc. Bikes with engines. Almost all of the bike brands from China, such as NST, BMX, and Buyang, are imports from China. The package contains a chain, Master Link, and Guide Roller. The center to center spacing between the pins is approximately 7/16" wide. The center to center spacing between the pins is approximately 7/16" wide.
👤This is not a chain. The roller diameter is too large and will not fit in the sprocket pockets. This was verified by the known chain and other sprockets. It was also poorly made. Some pins are tight. Some rollers are way too large and others are just too small. Garbage and waste customers can be sold time by another company.
👤The original smaller chain is under the cleaner chain.
👤You never know when you might need a new one, so I wanted to have an extra on hand.
👤It is a good deal, you get master links and an extra idler wheel.
👤My brother's motor bike chain broke in several pieces. I am glad he did not get hurt.
👤The product is a great price.
👤The side walls of the links are too thin and similar to a stock chain so it's probably not a heavy duty chain. The weight on the scale is not heavier than it should be. You can get a Podoy H chain here.
If you have a question or are not satisfied with the product, please contact them. You can find the order by going to your account at Amazon. Click the seller name to enter the store page. Click "Ask a question". If your sprocket is thicker than standard, they suggest bolts M5x25mm. Grease/lubricating oil is put on the thread of the wheel to prevent damage to the thread from riding. The thread size is 1.350 inch X 24T, the hole spacing for front and rear wheel is 44mm, please see the last picture. If you are concerned, buy carefully, there will be splinters or paint chipping during transportation. Light and very durable, the LxT is the front and rear of the wheelaxle. The size wheel is 29"/ 700c. The hole spacing for the front disc brakes of mag wheel is 44mm. The best safe speed for racing is 35 km/h. The standard 9 hole sprockets in the kit don't work on the alum wheel, buyer need to drill 6 holes in the middle of the sprocket to make it fit on the wheel.
👤They arrived on time, looked nice, but they should not be marketed as wheels for your road bike or ten speed. These things are too heavy for a bike for a kid. They looked like they might be able to sit in a wheel chair.
👤Make sure you get 12.9 grade hardware for your motorized bike. Smooth easy rolling, heavier than stock spoke wheels by at least a pound. You won't have to worry about lean on your tires if you align your studs properly. If the bolts are not aligned correctly, they will be off center. My area has a lot of ruts and potholes, so far the rims have taken bottoming out with relative ease and are holding up well. I would like to find some Shimano chromoly axles in the future.
👤I built a bicycle for a customer out in Oakland CA and asked if I could put some mag rim on his bike like I have on one of my other bikes, I said I could.
👤It's easy to install the set of wheels. It doesn't come with any information on what size bolts to use for the sproket. The correct bolt is 5mm X 12mm. I was expecting them to be heavier. That is not a reason to avoid buying. If using a motorized road bike, the wheel set is a must.
👤I initially bought these wheels because they looked great, but two months later I decided to put a motorized bike together, and the bolts broke, maybe they should have been more long.
👤These were the things I needed. I gave it four out of five stars. One of the bolt holes was stripped. I needed a bigger bolt. The rims are not false. I used 5mm bolts. When you purchase the bolts, I suggest taking the rim. To get the correct length.
👤I bought a set of wheels from this place last year, but they don't fit on the new set. I'm not going to but I will return the wheels first, the black set is the new set.
👤It's peeling paint. I got these four days ago. If you use a motor, it will rip the bolts from the wheel. It ripped it from the center of the bolt. The bolts come lose. I think I'm going to have to use a locking washer and tap bigger holes.
The product has a 12 months warranty. Please contact them first if you have any questions. They can help you solve the problem. It comes with a high hole Piston kit installed inside of the cylinder and a wide front mount. 40mm alum intake stud spacing; manual expeller. The cooling effect of the casting cylinder head increases the power of the horse. It would result in better performance for your bike engine. The casting cylinder head has a height of 51mm. Before assembling a cylinder, make sure the transfer ports are clear and the cylinder is screwed to the end bottom so the drill doesn't get through the end bottom.
👤This is an amazing combination that I am currently building but one con. I have it, but it does not have a windowed piston. I'm turning this engine into a race engine because it has a lot of low-end power and it's amazing that it has a lot of Torque. If you find yourself in need of a great engine look no further than the stock or modified one, I hope this helps you guys, there is a lot of things you can do to this if you know what you're doing. The engine seems to be a one that I was let down about because the stud on the front mount is not secured properly into the block. I'm going to take care of it and see how long it lasts, thanks again.
👤The item was damaged when I received it. I have not been able to find a way to contact cash power. A stud kit would solve my problem.
👤The bolts on the head were removed. The bolts were bent. The bolts were not grade 8 steel. The bolt that should be thread locked has been backing out.
👤The motor is cheap. They run great if you put in the time.
👤There was a rough thread in the spark plug hole. It is very difficult to install a plug. The engine is very hot. It will run cooler after break in. I hope so.
👤The jugs are from the factory. They cut the jug to a clean 52mm hole to remove the defected surface. They cut 5 rings in the jug. This isn't an iron sleeve. The liner is cast iron. They use cast iron bearings. At this point. The port's roof angle is not good. The jugs casted ports will not be inline with your sleeve because it is not index. The thickness of the liner is not evenly distributed. The liner has compression leak issues because it lacks a top shelf at the point of head contact. I went into more detailed photos after reviewing this head on my build break fix channel. This is not an upgrade from your 80cc motor kit.
👤This one came to me with the spark plug missing and the cylinder and engine were scared as if it had been used before.
The set includes a megaphone Exhaust pipe, 3 waterproof and Super Durable Motocards, an Awesome 24 Piece Sticker Pack, and all the tools for ages 6+. No electronics, 100% pedal power. No batteries are required. There is a limited product inventory, bike tool kit, bike repair kit, bike tire repair kit, bicycle tool kit, bicycle repair kit, mountain bike tool kit, bike patch kit, bike tools kit set, and more. The Mountian Compact Professional accessory supports the repair in a harsh environment and immediately continues to ride without danger. The Bike Repair Kit With Pump And Bag and Bicycle Tube Repair Patch Tool Kit are better than other similar products. You can use a nylon Velcro to hold the bicycle stand in place without losing it. Increasing your safety is their belief. This product is produced for experience, it is the most convenient bicycle indoor and outdoor tire repair.
👤I would suggest this to someone who uses a cruiser bike or just rides around for transportation, not someone who is an avid road biker or mountain biker house, it would interfere too much and make moving at high-speeds awkward. When you buy tools, you get what you pay for, so I suggest spending a little bit more money on getting some strong reliable tools, a few of them have soft metal and I damaged them the first time I used them. This is great for someone on a budget who just wants to have peace of mind.
👤Don't buy this if you have an electric bike. The tool is too small for removing the bolts. There was no rubber cement in the package. I'm very happy. I have a flat close to home. I decided to use the tool kit to get back on the road. I would not have been able to get this kit if I had not been out. The shop is better equipped. I'll be making my own kit after this experience.
👤The threads holding the strap to the bag separated after just over a year of hanging off my handlebars. Very disappointed. Would not buy again. The year of 2021. I had a flat for the second time. The wrench snapped when I applied pressure on the wheel. 2.5 miles from home. This proved to be poor quality twice.
👤This is a good kit. It doesn't have the most pieces, and they're not the best built, but you're not going to pay over $75 for it. The bag is large enough to hold your keys and phone, which is a nice bonus, and it has the bits that you'll need the most if you get stuck on the side of the road. I would have liked to see a pressure gauge addressed. It's easy to put a $2 one in there, but not to include it. Some of the parts don't have elastic strap spots, and are floating around in the bag. This is a poor design choice to save money.
👤I used the bone tool on the first day but needed to make an adjustment. It snapped in half. It is weak and cheap. The carrying case hangs loose on the bike, the straps are not made to overlap so that you can tighten it to the bike. Buy something else if you want to.
👤I went to check the spoke wrench on my bike after I got this kit. The kit was already paid for. There is a The bike I bought had some defects. I wore out one side of my brakes on my first ride so I ordered new ones and installed them using the tools from this kit. I got a lot better using this kit because the rear rim was out of round. The front rim needs to be done.
👤A good set of tools. Couldn't give 5 stars because of the carrying case. The case is awkward on a mountain bike, the only place I could find to make it fit was on the top bar, it flopped on my knees and hit my knees.
The headlight base is high quality and suits all kinds of bike. IPX6 waterproof, resist against splashing water in rain. If dropped carelessly, shock-resistant does not matter. Reliable protection, practical design, and durable quality. Not only does it keep you safe from unexpected pot-holes, debris, and any other hidden obstacles, but the additional loud bike horn also notice to everyone add as a secondary on the streets of your cycling. The default parts of the one electric fat tire bike conversion kit are motor with wheel, controller, display, brake lever, Thumb Throttle, and gift. The battery and tire are not included. The whole kit uses the KT system, so if you don't use it, other parts won't match the kit. The price for one electric bike conversion kit will be cheaper than the whole electric bike. Installation will be easy if they provide the installation introduction. You just transfer the original tire from the bike to the prepare motor and link all components. The installation will be done. The installation introduction was attached to the kit. Important parts include: rated power: 1500W, rated speed: about 50 km/h, fork size:135-142, and brake type: They will provide you with 100% qualified products and quality services. If you have a question about your kit, please contact me. Please contact me first if you can't get the refund because some parts broke. The 1.75-2.125 tire was matched by the 1500w brushless non- gear motor.
The Rear Hub Disc Brake Ball Bearing can be used. The mechanical disc brake is actuated by a cable. There are two sets of calipers and one set of rotors. There are aluminum alloy calipers, 12 bolts, and 2 steel G3 160mm rotors. It is easy to adjust power modulation. For use with brake levers.
👤These are well built and inexpensive. If you know the secrets of setting up and maintaining a machine. You will love these discs. My own fault is the only complaint I have. My middle finger was sucked into them. I think so... If you want to slide the strips between the discs, use a business card and cut a few out. If you want to give your rotor a hair's width to breathe and not grind, tighten up the mounts on your caliper and squeeze the brake lever. If you want to clean your pads, be sure to use rubbing alcohol or acetone and sterile cotton, as the oil in your skin will corrupt the bite. Seat your pads properly by not yanking on your brakes for the first few hours. After a couple hours of babying them, your brakes will be set and they will be fine for a long time. The man is thankful for a cheaper alternative.
👤I installed this kit on my Trek bike so I can pack it for bikepacking. I have installed mechanical disc brakes before on a different bike, so I am familiar with that. The instructions were easy to install, and neither did they get a single step wrong. Not to worry, no instructions included. I just installed the front and back in 20 minutes, just like I did before. If you don't know how to install disc brakes, you should watch a video on mechanical brake installation or review the installation guide for the AvidBB7. I think it would work the same as this kit. I think mechanical disc brakes are easier to install than rim brakes. I am 215 pounds and the stopping power of my Santa Cruz Superlight seems to work for me. I can't see a difference in stopping power. There is a I am very satisfied with the price.
👤I didn't look closely when I bought these. I thought that the time was right to replace the set that I have beat to death. I like the AvidBB7. I opened the box, saw the lower quality imitations, got packing tape, and re-closed the box. I'm giving them three stars because I'm sure they'll work well for what they are, a cheap brake that is good for stopping a bike that's only ridden slowly on pavement. Did the 160mm disc brakes fail on your balloon tire beach cruiser? Buy the brakes. Is the Huffy in need of an upgrade? Give these a try. Do the kids ride on the dirt trails? They will be able to take all the sweet jumps. Do you need a paperweight or other name brand brakes? This is your ticket. I'll never know if they work because there wasn't a chance I was installing them on my bike. It's possible that your bike is cheap enough to be what you need. They aren't right for me. If you want to get a AvidBB7's, you should pay at least 3x more than these.
👤The discs were mounted on new wheels. The front had a new pair of air forks. The back of the bike is being built. I spun the wheels after installing them. The discs were rubbing on the pads for a second on every rotation. I had to bend them to get them to stop. I didn't use the cables. I'll be replacing the whole set up with better brakes and better rotors before long, but they'll work for a short time.
Premium quality screws and bolts have been upgraded to improve performance. There are notes. The rider needs basic hardware skills, tools, and hours to install and fine tune their vehicle. If you don't have experience or the first time, please read their instructions and search "80cc bicycle engine kit" on the internet, it will give you a lot of help and help you fix the issues during installation process. The YD 100-CDH50mm set has a piston kit. No CDH sticker, 50mm bore, and better adjusting clutch a little before riding. Excluding manual, Cylinder head and Cylinder two in one piece, 50mm bore and improved magneto. 40mm alum intake stud spacing; Cylinder inner diameter 50mm; Piston outside diameter 50mm; 8mm front and rear mount studs; and Cylinder Piston outside diameter 50mm.
👤I've bought and rebuilt many China dolls. I know the one motor that is number one in my book, the anbullBT 100 one price cylender/head with the exhaust bending to the left, is the one that has a powerban that I've never felt before on their engine's even with all the upgrades. Every time I need a new China doll, the price is left bend all the way. I gave it more throttle after the break and it vibrates more than any other motor I've ever had, I don't think it's a yd 100. I think it's a cap from the manufacturer, I really wish I had used my money for a better motor, but you live and learn.
👤Delivery was fast and well packaged. I have used 5 different engines, but my favorite is the one I have used for 400 miles.
👤I liked that it came with spark plugs. I found nothing wrong after examining it. The head is already assembled, unlike the kit that is being sold. Will update after running. The best price for this engine.
👤I think it's a big 5 stars. It runs well with a few small adjustments. Minor adjustments were needed after about 100 miles. The only complaint was the amount of debris left on the inside when it arrived. Cleaning and port work is recommended.
👤The hardware that comes with the motor could be better if the bolts were tightened with more care.
👤Excellent engine. It was easy to install.
For use with brake levers. The Firestorm Zeda 100 HP bicycle engines have high performance heads. 50mm bore, 40mm stroke and US displacement. 78.6cc/40mm Intake and Round Exhaust. The rod is long. Increased weight capacity, low operating temperatures, and sustained power output across rpms. The coat has pearl anti-corrosion coating. The spark plugs and thicker crank case are used for bearings. Improved single piece cylinder, high end Allen bolts, and improved gas cap.
👤I will be adding another review once we get it working but so far the kit is very nice and I installed it on my bike, but this is not for a regular person, it is for someone who is advanced in a mechanical nature. I will have fine pictures soon. I got the bike working and it was a beast, this little engine got me going real fast. If you rate this item bad, I will give you some pro's and con's, but you should know that kit's are likely to give you bad items. Before you buy a bike, read if it will fix it. It's not hard to install a great engine. Heavy duty chain. It's easy to start Kit, but I'm not sure if it's worth it because you can ruin the engine and the throttle. You can pedal while it's on, but you can't pedal while it's off, I thought you could, but you can't! There is a It's hard to install and see where to put it. The Sprocket is cheap and will be upgraded later. It will not last long and you can get a racing spark plug for cheap. You need to drill a hole in your bike to put the throttle on. I didn't. I plan on doing it for safety. You can buy Greece for the gears and put them in every 6 months. I have to connect something to the Muffler because it bounces even though I tightened really hard. The kit is an amazing deal, but just some cheap parts.
👤So far, so good. Not a lot of miles yet. It runs smoothly without maintenance issues. It is important to have installed by an experienced technician. 3-23-2020 It's been 3 months and still running efficiently. There has been no engine maintenance needed so far.
👤This isn't made to fit on a quality bicycle frame. It seems like a good value. It doesn't fit anything perfectly because it's a universal kit. I mounted my kit on a mountain bike, but it took some modifications. The kit was designed for a cheap steel framed bicycle. My frame is made of aluminum and has larger diameter/thinner walled tubing than a cheap steel bike. I had to use a vice to "ovalize" my downtube to get the bike's frame to fit. To get the seat tube in the frame, I had to cut down the rear engine mount yoke in height and open up the saddle for it. There was not enough height to install the boot without a war and there was not a way to tighten the plug. The rear engine mount had a huge air gap because the angle of my frames' tubes was different than what the kit was made for. The mount was packed into the air gap to make it solid. There is a The next procedure was the intake. The stock cast aluminum intake put the seat post in the correct position. I had to cut the "Z" style intake down to an "L" and run it back and forth at 45 degrees after ordering an offset steel "Z" style intake. After attempting to mount the exhaust it was apparent that the exhaust went directly into the downtube of the bicycle so it was modified with several "pie cuts" that were welded shut and ground smooth. It seemed to work after it was installed and modified. It's rich and boggy on the bottom and the top, so I need to tune it. It's not fast, there isn't enough Torque to make it "zippy", but it's fun. This little thing is fun and sometimes less is more. I use it to run down the dollar store in town. There is a It's fun and cheap and I think it's worth the money. Prepare to cut, grind, bend, beat and cuss. Anyone with a can-do attitude and basic hand tools can make this fit nicely on a bicycle.
Before purchasing, please check the size of your original one. The bicycle engine kit has a speedometer. The bike engine kit fits most men's bikes with a V-frame, at least a 8.5" height clearance for the engine. The universal mount may be required for large bikes. The mixing ratio for gas and oil should be1:1 for the first 300 miles. It is important to avoid a motor lock up. The 80cc bike motor kit has a single cylinder, air-cooling, 2-stroke engine. The motorcycle has synthetic 2 stroke oil. Please use premium quality oils to prolong engine life. The air cylinder should be lubricating before it starts. 2 stroke bike engine kit has a maximum power of 2.2 kilowatts and a rated power of 1.5 kilowatts. The universal face plate is required for the larger frame size. There are notes. If a new car is leaking oil, take apart the bowl and bend the claw down a little to fix it. Remove the cap if there is no spark plug. The 80cc engine kit air cylinder might take a while to adjust to the load. Please limit the riding time to a maximum of 1 hour for the first few rides to avoid any problems with the motor. There are notes. The motor needs to be maintained after riding breaking time. Premium quality screws and bolts have been upgraded to improve performance. There are notes. The rider needs basic hardware skills, tools, and hours to install and fine tune their vehicle. If you don't have experience or the first time, please read their instructions and search "80cc bicycle engine kit" on the internet, it will give you a lot of help and help you fix the issues during installation process.
👤If you don't know what to do, just go on to the video and see how easy it is to put it together. There are lots of videos about these motors. I had a problem with my bike when I put gas to it, but I just put the tabs on the float and it solved the problem. I recommend red Lock tight and if you don't have an innertube try to find a old one, it's a lot of fun and you should buy it again.
👤Installation was simple and all parts were correct. It was easy to start up. The engine began to clunk within 1 minutes. The bike was stopped to examine the housing. The nut was loose and the tread on the shaft was stripped. The threads were fixed and the nut secured. I tried to start again, but couldn't. There was no spark being sent.
👤It's cheap and it's worth it because parts are all over the place. They all have a washer or 2. Overall 3.5
👤I was completely satisfied with this kit. It took me only a few hours to build it and it exceeded my expectations, it is one of the best things I have ever bought.
👤Good motor. It's better than the last brand I had.
👤The setup chain was too short and the clutch lever on the left side of the engine was short. The speedometer won't connect to the bike.
👤Fue un poco complicado de armar.
Bicycle motor kit 80cc 29 products from Anbull. In this article about bicycle motor kit 80cc 29 you can see why people choose the product. Arucmin and Fvrito are also good brands to look for when you are finding bicycle motor kit 80cc 29.
Anbull, Arucmin and Fvrito are some of the best brands that chosen by people for bicycle motor kit 80cc 29. Find the detail in this article. Cdhpower, Cdhpower and Xch Robots are also brands that their products are worth to check.