The center to center spacing between the pins is approximately 7/16" wide. The engine is the 100CC. They used a generic version of the user manual for 80CC/100CC because they look similar. It comes with all the necessary hardware for easy installation. Heavy duty metal engine body. The max.speed was 48 km/h. Fuel type : 90#; N.W: 11 kilogram; G.W: 12 kilogram. It's for most 26" and 28" bikes. The frame should have clearance between the bottom brackets and the top bar of 9-11mm, and the diameter of the frame tubes should be 25-28mm. 50mm bore single piece cylinder, an upgraded CDI, Performance Speed Carburetor and more, high performance Speed Carburetor, silver anti-corrosion coating, high performance CDI with Yamaha components, improved magneto, high end allen bolts, improved gas cap. The mixing ratio for fuel and oil is good for the first 300-500 miles, but it is not good in the summer because of the hot weather. Please limit the riding time to a maximum of 1 hour for the first few rides to avoid any problems with the motor. If you have a question or are not satisfied with the product, please contact them. You can find the order by going to your account at Amazon. Click the seller name to enter the store page. Click "Ask a question".
👤The bt 100 engine kit is uncommon to fine one of these engines. There are a few issues with the bt 100 engine kit. The magnet seems to be weak on one side. If I am able to find a replacement, I will have to.
👤It was a great way to get back and forth from work. It was amazing to feel that kind of power on a light frame bicycle. I added a 36 tooth sprocket and it definitely increased speed. It went from 30 mph to 35. I added a air filter and rubber motor mounts to make the motor less vibrate. All in a great product. It is very easy to put together.
👤The motor kit is great and there have been no issues so far. It's worth $200, but not if the exhaust isn't able to upgrade or change, my buddy built it for me and you can contact him on his Facebook page called - New motor bike builders.
👤They changed the engines. Either that or they have a few different ones. I have no issues with the motor. The chain was changed to a two bolt because I didn't use them enough. There is a great engine with lots of power.
👤I built and bought many engines because I use them for my food delivery job for two years now. The engine and accessories are the best yet. The bigger and better design of the carb makes it non-standard. If you buy a 100cc engine from bike berry, they will send the other ones. If you tighten the studs all the way in, they are not long enough to put bolts on. The other accessories were all of the same quality, and it looked like this guy took the time to package them. One thing I like about it is that the head came assembled, everyone else started making the customer do it, which is a pain in the ass. I just connected it to the bike. I learned that you have to be careful with the journal bearings, there is only a small film for them to ride on, and 3cc of oil in the crankcase, on my last 100cc from bike berry. Don't accelerate down hills when the engine is not running. I'll never find a 2 cycle engine that will get more than 5000 dollars worth of food deliveries done, but I will update when this engine takes a bad turn. It was an edited version. The motor took a bad hit on me. It has been 3 or 4 months of hard work delivering food. This engine has made me more money than any other. It was probably my fault since I forgot to put oil in my car before I left the gas station. It can happen in a few seconds if the circumstances add up. My mind is against me, and it's been so long since my back tire or my engine had ruined my day that it had to intervine! What an ass! I watched the destruction of the engines. I bought an extra one, I will be much more cautious and get an accurate picture of how much better this engine is than the rest.
5. Their goal is to provide a good service and shopping experience. You will be protected by special customer service from the store. If you're unhappy, please contact them directly via Amazon. Within 24 hours, they will take care of you. Non original replacements. Baja BA 150cc is a fit. ATV X15 X18 X22. The Nini Pocket bike has a 70cccccccccccccccccccccccccccccccc There are scooters, mopeds, ATVs, dirt bikes and go karts. Fit for 49CC. 60CC 66CC The bicycle engine is 80CC. The package includes a fuel petcock filter kit and pocket tape. If you didn't receive HURI branded pocket tape, you could apply for a full refund. If you didn't receive HURI branded pocket tape, you could apply for a full refund.
👤I couldn't find the original valve. The kit and valve did the trick. I had to grind it to get it on the mount. 6mm is the length of the hose. The original was set up so that the extra hoses and clamps could be used. The motor is a Honda clone.
👤There is plenty of extra line for whatever you need.
👤It works well and is built to last. It came with everything I needed to do the job well. I lost a useful gift that came with it. If you feel friendly, please send me another tape measure!
👤I no longer go through gas on my pocket bike.
👤Plug and play is easy to use.
For use with brake levers. The Firestorm Zeda 100 HP bicycle engines have high performance heads. 50mm bore, 40mm stroke and US displacement. 78.6cc/40mm Intake and Round Exhaust. The rod is long. Increased weight capacity, low operating temperatures, and sustained power output across rpms. The coat has pearl anti-corrosion coating. The spark plugs and thicker crank case are used for bearings. Improved single piece cylinder, high end Allen bolts, and improved gas cap.
👤I will be adding another review once we get it working but so far the kit is very nice and I installed it on my bike, but this is not for a regular person, it is for someone who is advanced in a mechanical nature. I will have fine pictures soon. I got the bike working and it was a beast, this little engine got me going real fast. If you rate this item bad, I will give you some pro's and con's, but you should know that kit's are likely to give you bad items. Before you buy a bike, read if it will fix it. It's not hard to install a great engine. Heavy duty chain. It's easy to start Kit, but I'm not sure if it's worth it because you can ruin the engine and the throttle. You can pedal while it's on, but you can't pedal while it's off, I thought you could, but you can't! There is a It's hard to install and see where to put it. The Sprocket is cheap and will be upgraded later. It will not last long and you can get a racing spark plug for cheap. You need to drill a hole in your bike to put the throttle on. I didn't. I plan on doing it for safety. You can buy Greece for the gears and put them in every 6 months. I have to connect something to the Muffler because it bounces even though I tightened really hard. The kit is an amazing deal, but just some cheap parts.
👤So far, so good. Not a lot of miles yet. It runs smoothly without maintenance issues. It is important to have installed by an experienced technician. 3-23-2020 It's been 3 months and still running efficiently. There has been no engine maintenance needed so far.
👤This isn't made to fit on a quality bicycle frame. It seems like a good value. It doesn't fit anything perfectly because it's a universal kit. I mounted my kit on a mountain bike, but it took some modifications. The kit was designed for a cheap steel framed bicycle. My frame is made of aluminum and has larger diameter/thinner walled tubing than a cheap steel bike. I had to use a vice to "ovalize" my downtube to get the bike's frame to fit. To get the seat tube in the frame, I had to cut down the rear engine mount yoke in height and open up the saddle for it. There was not enough height to install the boot without a war and there was not a way to tighten the plug. The rear engine mount had a huge air gap because the angle of my frames' tubes was different than what the kit was made for. The mount was packed into the air gap to make it solid. There is a The next procedure was the intake. The stock cast aluminum intake put the seat post in the correct position. I had to cut the "Z" style intake down to an "L" and run it back and forth at 45 degrees after ordering an offset steel "Z" style intake. After attempting to mount the exhaust it was apparent that the exhaust went directly into the downtube of the bicycle so it was modified with several "pie cuts" that were welded shut and ground smooth. It seemed to work after it was installed and modified. It's rich and boggy on the bottom and the top, so I need to tune it. It's not fast, there isn't enough Torque to make it "zippy", but it's fun. This little thing is fun and sometimes less is more. I use it to run down the dollar store in town. There is a It's fun and cheap and I think it's worth the money. Prepare to cut, grind, bend, beat and cuss. Anyone with a can-do attitude and basic hand tools can make this fit nicely on a bicycle.
Feel free to contact them if you have a problem in 24 Hours,Storage Bag keep cover, do not worry, they will do everything they can. Powerful welder capable of welding mild steel, weld steel, and cast iron. The reliability of welding machine is improved by the IGBT power device. The welding machine has a professional certificate for added safety. MMA welder devices are inspected to ensure their reliability and efficiency. Excellent Arc stability, built-in anti-stick, hot start, and built-in anti-stick. The welder has a compact design, easy for translation and storage. It's very convenient and can be used anywhere. Decrease the damage of Copper and Iron, increase the welding Frequency, and energy-conserving result is remarkable. The output voltage is stable and can be adjusted for the electricity network. The MMA welder can be used for welding mild steel, aluminum and other metal materials. The MMA welder can be used for welding mild steel, aluminum and other metal materials.
👤I was hesitant about buying this welder because it was so cheap. I've been looking for welders for a while. I kept going back and forth between Miller and Lincoln but could not understand how they justify the prices. Next day, the welder and rod is on my porch, thanks to Amazon. I fixed my trailer first and then used the max current welding channel to burn a couple of pounds of 6013 rod. The strike was easy and flowed nicely. I was happy with the work. I spent 5 hours welding the structure to the 50' x 13' addition to my barn. I put everything together with my boat. The welds are not good. The wire sticks metal together. I started with a 16ga rod. Square tubing, trusses, and purlins. I adjusted the Amps from 55 to 75 to 100 to 130. The rod wouldn't flow like the 6013. It was so hot that it would burn through the steal. The rod would stick when I ran too low. I decided to get the 6013. This thing flowed like butter after I adjusted the Amp to 90. The welds were strong, the rod flowed evenly, and starting the arcs was easy. The thing is small and runs on electricity. I had to cut my teeth on the Lincoln because of the lead wire. I'm not sure how they justify the price for 40 year old technology when the welder is over $300. It's not a problem to reach 8' because the leads with the machine are longer than mine. I ran up and down the structure after attaching it to my ladder. My welds were upside down on galvanized metal. The person welding the bad welds was not the welder. I have made many tool purchases over the years. I'm amazed at how well this welder worked.
👤If you are looking for a cheap lightweight welder that will do your basic stick welding, then here you go. It is small enough to fit in a backpack. The machine ran perfectly out of the box. It is pushing on a lead. The bigger wire would be better off than the 220 plug in. The stinger is cheap and small. It works. It is a good machine for the low cost.
👤I decided to try this brand because it's only 120v in the U.S. My experience with older, first generation stick welders has not been good. I was expecting a lot of disappointment since it was a small and light weight. I haven't used it a lot but it works so well that I was blown away. I had to crank the power dial down to 70 if it was going to melt the steel. This was for the two pieces of rebar. It doesn't have a tissy-fit if the rod gets stuck on the weld and the unit stays cool. I don't know how long it will last, so I give it 4 stars instead of 5.
👤It runs like a champ. It hasn't been tried on 120 volts. It works very well on 240. Definitely upgrade the ground clamp.
This product comes with a 12 months warranty. Please contact them first if you have any questions. They can help you solve the problem. It is complete parts for building your bikes. The YD 100 and the PK80 are used for 2 stroke motor. A new chain with 4 bolts. The 44T sprocket and 2L gas tank are standard.
👤There were no dents or broken things. Really liked the handles. The screws were missing. But other than that. Happy with the purchase.
👤When I ordered it, I thought the engine was included. I was able to use the parts, but I really wanted the engine.
👤There was no flat plate at the U-bolts to mount the front of the motor on the Schwinn and Huffy bikes, the rings were cracked and the brake lever was missing.
👤I had better luck with another brand. There are leaks of oil. One of the bolts is missing.
👤The chain broke on the first use, the throttle cable was not very durable, and the fuel filter hose was leaking.
👤The kit messed with tank lakes.
👤Came early but didn't have the parts.
It isdurable: One of the most reliable and durable bicycle repair stands is available for home or shop uses. They can keep enough parts for any claim in their warehouse, and offer a 5 year warranty on the rack. You can Mount it with your own preferences. OutSTANDING CONVENIENCE- Anodized coloration. If you need to, you are welcome to contact them. The Handle Throttle Grip will give you more confidence in riding. If you have further questions, please contact them. The carburetor is under 90 days warrenty. If you have further questions, please contact them. The carburetor is under 90 days warrenty.
👤The shade of red is very nice. Can't wait to install it. When you tighten down, pay attention to what's going on, why is it sticking? It's a very easy fix that took me 30 seconds to figure it out. The solution can be seen in one of the pictures I took. People need to think more. Solid throttle other than that. Happy with it.
👤It looks great, but I used it with handguards and it didn't stick, it was just a simple bolt on product. The throttle tube is threaded and not a solid piece so it can come loose and be dangerous. It looks good.
👤I bought it for my 125 cool ster and it does the same thing as everyone else, it sticks when you tighten it, how are you supposed to use it if you can't tighten it with the two screws?
👤I bought this for my wife's pit bike. I spent the last week trying to get this to not stick. It works perfectly when everything is tight, but as soon as you tighten it down it sticks.
👤The quality here is very good. Everything fits together perfectly, no blemish in appearance, inside or out, and it looks good even if you can't see it. The cable housing was too short for my application, but it is gorgeous and tough with a steel braid outer sleeve. Installation was easy and the operation is responsive. Will buy again.
👤Works well! It snaps right back into place. I had to make it function correctly, but it works great. The little plastic things seemed to work after I removed them.
👤The reviews say that even with adding shims, it still sticks full throttle because of the metal shavings from the part inside.
👤Don't waste money or time. The cable did not work for the bike that was listed. The cable was not worked out of it because it was packed in a small box. Even if it fit, it wouldn't have been safe to use a child's dirtbike with a cable that was not perfect.
Cyclists designed the tools that are built to last. The bike wrench set comes with a lifetime warranty. It's used for brake systems of bikes. The inner diameter of the freewheel threaded hub is 34mm. The position is front or rear. The R-140mm is F-160mm. R-180mm. There are Buffers included. F160 Front Brake is also known as F140. If it is installed at the front wheel, it will fit a 160mm rotor. R160 Rear Brake is also called F180/R160. If it is installed at the front wheel, it will fit a 180mm rotor. The package contains a mechanical bike 160mm front and back brake disc kit.
👤This is for a weird application. The levers are real clunky, the rotors are not compatible with my wheels, and the calipers have the smallest pads I've ever seen. You get what you pay for.
👤I thought the descripton of 48mm disc bcd was a mistake as I couldn't find a bike wheel with that geometry. They will not mount on the international standard of 44mm because they measured 46mm. My review ends there. Send them back.
👤Garbage is what the cables for where I am are. The wind out here is salty, but so far it has not damaged the cables. Walmart sells heavier replacement cables that work better here.
👤The brakes don't work well. The wheels didn't fit the rotors. I had to order all new brakes because the stopping power on my old rim brakes was not as good as the new ones. I will be getting a better set of brakes and removing these from my trail bike.
👤Everything works well. The quality of workmanship is the only turn off, it looks like it was just taken out of the mold and assembled right away.
👤Gave up on bike shops after a lot of bad experiences, installed these brakes in an hour and 30 minutes of riding.
👤The only good thing about package was the calapers.
Before purchasing, please check the description. Thank you! They are always here to provide you 100% satisfied after-sale service if you have any problems or concerns. 100% New high quality and complete electrics all wiring harness wire loom assembly for GY6 125cc 150cc ATV. The Chinese made electric start upright engine is compatible. GY6 125cc 150cc ATV, QUAD, Coolster, Go Kart, 4 wheelers, Scooter, buggy, Motowork, and more. GY6 125cc 150cc ATV/ QUAD with 6 coil stator is compatible. This assembly does not fit 50cc and 70cc. The Zongshen Lifan ATV has different stators. The package includes:CDI, spark plug, ignition coil, solenoid relay, rectifier, ignition switch, ATV switch and magneto stator. The package includes:CDI, spark plug, ignition coil, solenoid relay, rectifier, ignition switch, ATV switch and magneto stator.
👤Please read and hopefully this will help others. There is a The harness I used to replace my harness in the A series was good, but the one I used to use was bad. There is a The harness wasn't set up for this atv because the connectors weren't wired to the right spot. I was able to use some of the wire and connections from the old harness to make the new one work. Also, note: This will work if you are good at wrestling and selling. There is a The wiring diagram that is provided for this kit is both good and bad. It is very basic and difficult to go through. I wrote a key at the top of the diagram of what color wire does in the harness. Think about how the key off and the key on should work in this situation, and you should be able to walk through it. I do this for a living and this was helpful in my case. I had trouble shooting due to a no start issue. The kill switch on the main ignition/light/choke switch needs to be reset after being moved either right or left, so be aware of that. If you push the kill switch in, you will not get a spark. The crank switch needs to be depressed in order to get the start solenoid to close. This is where I had a no crank and no spark situation. The front head lights in my case had to be switched on. I didn't need to get anything else because the other electrical components worked for me. There is a I think this harness was worth it in the end, even though it is a lot to read. I needed the harness. The attached picture shows how I walked through the wiring diagram. The colors are not all written out on the top but you can add to it if you need to. Good luck!
👤The go cart was worked on. I had to change the wires. The push button switch needs to be changed. I cut a new harness because I knew the engine would run. I had to dry fit the kit before I could start it. I got a harness and stator kit from another vendor on Amazon for 5 dollars less than the one I got. The kit has been working well for a week now. Many of the connections are not used. Some are for tail lights, safety switches, and headlights. As you go, you figure it out. It's a good thing. It works and the machine runs. The Chinese stuff is not high quality. It gets you out of trouble and makes you run again. Happy wiring. Good luck.
👤The wiring harness is not working. I didn't get the start butting to work when I hooked it up. The harness was pulled apart and there was a mess. I would return it if I hadn't pulled it apart. I had to use my old CDI because of the faulty box. Prepare to use a meter with this harness. I wouldn't recommend it.
The package includes:CDI, spark plug, ignition coil, solenoid relay, rectifier, ignition switch, ATV switch and magneto stator. The vibrelli Torque Wrench is a high quality, click drive Torque wrench that lets you tighten to the exact Torque every time. A bicycle Torque wrench set is essential to not over tighten or strip your bolts, because most bikes now come with specific Torque rated components. Protect your ride. Certified Precision has a Torque range of 2 to 20nm. Torque wrench is made in Taiwan, triple tested (2mn, 12nm, 20nm), and comes with an individual tested Calibration Certificate. The tools you need come with Allen/Hex. T10, T25, T30 are the names of the testicles. A protective hard case has a 100mm extension bar in it. The perfect road bike and mtb Torque wrench. The slim design and anti-slip textured handle make it easy to use in difficult spaces. Setting the correct Torque is easy because of the spring-locking collar. It is important. When the correct Torque is reached, listen and feel. Read and watch their instructions on how to use this wrench correctly. Cyclists designed the tools that are built to last. The bike wrench set comes with a lifetime warranty. Cyclists designed the tools that are built to last. The bike wrench set comes with a lifetime warranty.
👤The keys for the bicycle are made of solid construction. The case is great.
👤This is my first wrench. It was easy to learn how to use correctly from the clear instructions. Once you learn how to read the numbers, adjustments are easy. When I tried to Torque a mirror setscrew with one of the allen bits, it kept slipping and wouldn't grip into the allen setscrew. I tried it with my allen wrench. I had problems getting a promotional rebate from the company. My emails to them were not going through for some reason. The company was very proactive in understanding the problem after we re-established our email communication. Their post-sales support was great.
👤Toque settings are easy to set. The values are on the left and right. When turning the knob, click into place. You can turn the knob at the next 1 N.M. If you're on 2 N.m., turn the knob to the right and you're at 2.1 N.m. If you turn the knob one full rotation, you're at 3 N.m. Pull the knob down a bit. It is put in place at the detents. It's easy to dial in the value you want. When you're at the right Torque value, the head breaks away from parallel while it clicks, so you know when you're at the right Torque value. It's better than the simple hard-to-detect "click". Even though it's called a "click type" wrench, I think those with heads that break away should have their own category. You can feel, hear, and see when you're at the right value. There is a The tool is well made and engineered. It looks expensive. There is a The case is small and has a strong clasp to hold it shut. The kit includes Allen bits, which I already had, but is nice to have more handy. The accuracy certification is printed on glossy paper. My certificate is labeled with serial #90355, so hopefully yours is different. The accuracy is guaranteed better than 4%, but it wasn't obvious in the text. It was substantially better than mine. The tool's characteristics include: a 1/4" drive bi-directional Torque Wrench, Metric Torque Values, 2-20 N.m, tested +/- 4%, and certification of accuracy and the results from the certification testing. Over the years, I have had a number of different types of wrench, with different ranges. This is the best wrench of them all. The more I use it, the more I like it. It is a pleasure to use a tool of this quality.
👤The set is made well and works as it is supposed to. The bits and wrench have good tooling. The markings are legible and the positive stops on the correct settings are helpful. The "click" is solid when you reach the correct Torque. It comes with paperwork showing it has been adjusted. The case is strong and holds everything. It states there is a lifetime warranty, and I have used customer service from vibrelli for another product. This is a very good deal at $50, and it looks like it's the same price as other sets.
The package has a carburetor, gasket,O-ring,Fuel Filter, and air filter. The engine side has an inner diameter of 26mm and an outer diameter of 48mm. The new Aftermarket VM22 26mm Carburetor is brand new. compatible with vm22 26mm. The car is 125cc. 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apoll If you have any questions, please feel free to contact them by email, they will solve it for you in the first time! If you have any questions, please feel free to contact them by email, they will solve it for you in the first time!
👤The stupid plastic isolator they send with the carburetor is only 20mm. Someone tightened the fuel air screw. There is a brand new box. Also, note: You will need a new throttle cable if you install on an Apollo pit bike. Stock cables do not work with this car.
👤We were having a hard time trying to tune our TaoTao sr125. Two different types of carbs wouldn't tune properly for anything. We have this one. It started right up fist kick on choke and was almost dead on where it should be. It might be a bit rich on the main jet. I will do more testing. The gasket is not the right size. It is for a 20mm version of the smaller bicyle. I had an extra gasket around that was the right size. I think I got lucky. I was not going to run this set up with a smaller gasket. Take my word for it. If you don't want to be angry when you get your food, you need to buy a separate one. I think this is a good car for all the items included. The spark plug seems to work. I don't know how those will hold up, I used my own fuel lines. Everything seems good. Make sure your car isn't malfunctioning. Before I put it on, I took the carb apart. Check the jet size. If you use the intake manifolds they give in the kit, it seems like a good idea. I highly recommend you buy a separate intake manifolds gasket with the correct inner diameter. Happy Brapping!
👤This was the real thing. If you want a 125 to have lightning quick response and eventually grunt up to 60+mph, then this is the piece you want. Thank me later for spending the extra. I tried to find the cheaper one that was better. Don't waste your time, measure the current one, then order a mikuni. It was easy to install. It will be a breeze if you take a video apart while you watch it.
👤I have apollo 125cc and I love the product and would recommend it to anyone that wants to buy a over seas bike.
👤The Apollo 125cc dirt bike has a good quality and easy to install. The kit has a throttle cable needle that you need to change. I installed the needle that came with the kit. Don't use the parts in the kit for quick fixes. The bike is like a kitten. The quality of the car is good for the price. Buy it. Oh yes. It was shipped very fast.
👤The air filter was leaking right out of the box, but it was fine. There is a Sonic cleaned the car. It was back to ripping the Z50.
👤It shows that it is not the real thing. This is better than the stock car on Chinese bikes, but it is not very good. This item is exactly what you are paying for. It may or may not be worth it. This works well to get the bike up and running. This is not what you should get for the bike. A real Japanese Mikuni is years ahead in quality.
Brand new and high quality! If it fits your model, please check part comparibility. High quality. The main jet kit is brand new. The copper used in the jet kit is resistant to oxidation and has a long service life. The total length is 8mm, the Diameter of head is 7mm, and the thickness of the head is 3mm. The carburetor main nozzle is compatible with 125cc 150cc 200cc 250cc motorcycle engines. A set of 12 Carburetor main nozzles. The main nozzle of the set is #75-102(#75 #78 #80 #82 #85 #88 #90 #95 #98 # 100). The main nozzle of the set is #75-102(#75 #78 #80 #82 #85 #88 #90 #95 #98 # 100).
👤It is a Jet, what can I say? There are 5mm threads that fit Speed NT Carbs. The size is printed on the side of the jet, which is great. This is a must buy if you want to get the best performance out of your motor.
👤Unless they give you a cross Guide to reject a Mikuni Carb, you are out of luck. The jets were purchased for a good reason. I find this laughable because it states it works for my bike.
👤The vm22 clone I bought from Amazon was the same one I swapped the pit bike for. These and other sizes work perfectly for me. It's better when you can jet for conditions.
👤The B-set works great in my 2020 Kymco Super 8 50x stock car. The heads are slightly larger than stock.
👤I bought these for a knock-off. These worked well for it, but the car was not up to par. I was surprised to find these also fit the 26mm nibbi, I purchased a Nibbi which was 800-211-2519
👤You have to measure each one with a welding tip cleaner because there is no size stamped on these jets. The butt has pain. Do not recommend.
👤The jets are large. They won't fit in the trx90
Bicycle motor kit 150cc products from Anbull. In this article about bicycle motor kit 150cc you can see why people choose the product. Huri and Zeda are also good brands to look for when you are finding bicycle motor kit 150cc.
Anbull, Huri and Zeda are some of the best brands that chosen by people for bicycle motor kit 150cc. Find the detail in this article. Dekopro, Donsp1986 and Motorcycle Pro are also brands that their products are worth to check.