Best Bicycle Motor Kit 125cc

Kit 16 Aug 2022 10+ Comments Open

1. Brushless Controller Throttle Motorcycle Conversion

Brushless Controller Throttle Motorcycle Conversion

The BH-Motor magneto stator is for 50cc. The Kunray MY1020 Brushless Motor has an Electric Brushless DC Motor, a Full Copper coil, and a high quality more long life. The motor has a rated power of 3000W and a current of 45A. The BLDC controller has 48V, Proctect Vol 42V, Power 3000W, 24 Mosfet, Current 50A, Phase Degree: 120. The handlebar has a twist Throttle. The Universal Accelerator Handlebar has a Throttle Twist Grips. The reverse functions and wire length are included. The material is high quality. The suit includes: Electric Scooter, Mini Electric Motorcycle, Razor Push Scooter, Ebike Bicycle, Go Karts, E-bike, E Tricycle,Mid Drive Motor Kit, Complete Set,DIY Engine System, and more. What you get is a motor, controler, and a manual.

Brand: Kunray

👤If the builder knows what they are doing, this motor is very powerful. There is a The builders who have used this motor say they are disappointed. They weren't fully aware of what it could do because of the incorrect install. This motor can produce enough performance for a 300lb rider to reach 55mph on a Razor MX500, if set up properly. It is powerful enough to do a wheelie and throw a 300lb rider off the back with no issues. Yes... FLING... A 170lb rider on a Razor RSF 650 is going to get to 66 mph on a flat road in subpar conditions. A quad to 37mph, a Pocketmod to 49mph, and an SX500 to 58mph are not stable. There is a There were 8ah batteries. The original #25 chain and rear sprocket were used for these speeds. There are some things that are CONS: The package that this seller sells seems to be the cheapest one. The motor stand on the bottom is what "foot" means. It doesn't mean foot pedal. It doesn't translate. Most things don't translate. It's easy to understand or at least figure it out. The wires in the harness can be mixed up. If your motor is not running in a straight line, you should move the hall sensor wires around. The colors are green, yellow, and blue. The 3 speed switch wires are often messed up, so you have to switch them around to find the correct one. You don't have to use all the wires. They are not very good. Cut them off and get some other things that would be better. There is a The seller gets 4 stars because they are very good with customer service. There is a It is worth it. You will have to ignore the people who say it's bad because it's in Chinese.

👤Plug and play. I've been pushing the motor hard on this 2x2 vintage Rokon trail breaker. The batteries are wired in series with a standing voltage of 82.3

👤My Razor RSF650 can go up to 45 mph on a flat surface and 40 on a slight uphill. It's a trip that keeps up with traffic. The kit has sprockets. It is ok. You could get better performance with a larger rear sprocket. I would say this kit gave me what I wanted. Installation was relatively easy and I was surprised at how compatible it is. You need to have an idea of what you're doing. I read all the reviews before I bought this and I'm pretty sure that everything negative said was either something not installed correctly, not connected, or issues with the battery not this kit. The 54 tooth rear sprocket has been swapped for a 62 tooth one and the top speed is now 35mph.

👤The product is not damaged. I got it to convert my bike. The mechanics and electronics are all working for me. I don't know what the hard boot wires are for because I tried to start it but nothing happened so I disconnected it. The motor controller doesn't do electronic breaking, so I needed to mount the motor so the sprocket was on the left side of the bike. When the motor controller is first disconnected, I'm going to have some relays in series to connect the three phase rectifier back to the battery. I haven't tested it yet. The direction of the motor's spin is important because the controller does not allow full speed in the reverse mode. You need to do the same thing to the leads of the holifex. The holifex has a lot of cords. There are two red and two black ones for power and the other three correspond with the main motor inputs. I changed the color of the motor. I tried it on the holifex and it didn't work because they didn't correlate the color of the wire in the holifex with the color of the motor, so you might have to cut a strip and try all combinations. You have to wire it to go in the other direction. The wires from the controller should be cut. The Chinese on the handle is a complaint. It's easy to remember once you try them all. If you want other people to know, you can take a Sharpe marker and Mark 123 and FR on the switches. 1 min to do all of that! When I get a battery with enough power, I'll add some statistics, but a 5p 12s battery got me to 15mph on a road with a low setting. Med and high seem to try and stop. I think my bms are controlling the controller. I'm going to test it, but someone said it could get you up to 60mph. There is a It can be hard to figure out the wires coming from the motor controller. I'm going to make a completely new battery that will be 20p by 20s, and I'm going to make it in four separate packs, each with 20 rows of nickel, to give me the maximum amount of nickel to spread out. I'm going to use 20s bms. If you want to make your own regenerative braking on top of the rectifier, you'll need a 1500w boost conversion with constant voltage control. The solar panel can be plugged into the boost conversion to charge the battery. If you want to charge the battery with a wall outlet, you can get 1100w for 30 bucks, but you need to research ahead of time how to turn it on. You might want to look into a step down from 72v to 12v to power low voltage equipment. I would suggest getting the step down to 12v and then a 12v to whatever you need because a lot of DC stuff uses 12v. A battery power output monitor is a good idea to keep track of Watts and battery voltage. If you're going to use this motor, it's probably the cheapest one for the wattage, but the in wheel motor is a lot more compact and takes up less space in the frame of the bike that could be used for battery. I just learned how to make an in wheel motor and I think I would probably make my own motor and motor controller, even though I don't know a good source of cheap coated copper wire. This is probably the best option for the average Joe, but they should buy a chain tensioner. It will save a lot of trouble if you just do it.

2. HURI Universal Inline Petcock Motorcycle

HURI Universal Inline Petcock Motorcycle

5. Their goal is to provide a good service and shopping experience. You will be protected by special customer service from the store. If you're unhappy, please contact them directly via Amazon. Within 24 hours, they will take care of you. Non original replacements. Baja BA 150cc is a fit. ATV X15 X18 X22. The Nini Pocket bike has a 70cccccccccccccccccccccccccccccccc There are scooters, mopeds, ATVs, dirt bikes and go karts. Fit for 49CC. 60CC 66CC The bicycle engine is 80CC. The package includes a fuel petcock filter kit and pocket tape. If you didn't receive HURI branded pocket tape, you could apply for a full refund. If you didn't receive HURI branded pocket tape, you could apply for a full refund.

Brand: Huri

👤I couldn't find the original valve. The kit and valve did the trick. I had to grind it to get it on the mount. 6mm is the length of the hose. The original was set up so that the extra hoses and clamps could be used. The motor is a Honda clone.

👤There is plenty of extra line for whatever you need.

👤It works well and is built to last. It came with everything I needed to do the job well. I lost a useful gift that came with it. If you feel friendly, please send me another tape measure!

👤I no longer go through gas on my pocket bike.

👤Plug and play is easy to use.

3. Mingdun Carburetor Carb Mikuni 88 150

Mingdun Carburetor Carb Mikuni 88 150

We promise to give you the best in customer care and a 100% product guarantee. If you have an issue with the item, please contact them by e-mail, they will try their best to resolve it within 24 hours. It is widely used on 125cc-250cc Engine Motorcycle Dirt Pit Bike Replaces N 100/604. The package has 15. Main Jets for N 100/604 26mm 28mm VM22 and VM26 are known as the X Carb. The Jets are engraved with it's number. The thread length is 5mm, the cap height is 4mm, and the thread size is M5x 0.75mm. Your trust is deserved with safe transportation. Your trust is deserved with safe transportation.

Brand: Mingdun

👤Some of the jets had no stamp on them, but they were shipped fast. I didn't have the 120-130 jet sizes for my predator motor.

👤The 130 jet has threads that are too small. There is a The jets included had the correct 5mmx0.8 threads. The 130 size jet had 6mmx0.8 threads, which is atypical for a metric thread size. The 130 size jet had 6mm threads instead of 5mm, so I ordered a replacement set. The 130 size jet is not usable because the threads are too large and don't match the rest of the set.

👤The jests had bigger thread pitches. The ones I needed had bigger thread pitches.

👤Excellent quality jets at an amazing price.

👤The set is good and comes with what I needed. A 135 jet was used for the Coleman 200u with a predator.

👤It's easy to make a mistake if you miss the 105 and get two 145. I was able to read the numbers. It seems like a good product and good quality.

4. Ignition Solenoid Voltage Regulator TOPEMAI

Ignition Solenoid Voltage Regulator TOPEMAI

All of the original parts are backed by a 180 day return. The package contains: Ignition coil, 5 PINS CDI module, 4-pin Voltage Regulator Rectifier, Solenoid Relay, and 3 electrode spark plug. The item is for 50cc. 90cc. The horizontal engine is not for the GY6 or CG engine. The box is for Chinese made 50cc 70cc. 90cc-110cc 125cc 4-stroke. The ATV goes karts and the bike is a pit bike. 50cc 70cc 90cc has a 12V Regulator Rectifier. 125cc. Quad 4 Wheelers were Moped. Dune Taotao. The Buggy Sunl Jonway was driven by the woman. 50cc 70cc-110cc 150cc 250cc starter Solenoid Relay. The Sunl Baja is named after TaoTao Roketa. The kinroad ATV is owned by Kazuma Sunl. If you have a problem, you can contact them by email. If you have a problem, you can contact them by email.

Brand: Topemai

👤The mini quad had a very weak and intermittent spark. I suspected the components when the stator gave off good voltage. It ran like a champ after it was replaced with one pull. The price is great.

👤I had to redo my wiring on my go-kart, and one of the things I had to do was add a spark plug boot.

👤Don't waste your money if you swap out the same parts. I have a mid 80s kx65 and I said that this kit will work. It doesn't. I wouldn't have bought this if I had known the wiring wasn't there. There was no install instructions. I am not going to try to wire this up with braille. I wouldn't have bought it if I knew what wasn't included.

👤The connecting fittings for my hammer head engine were not correct. I will have to cut off the old one.

👤The coil did not work on our setup, but everything else worked great.

👤If you want horn, lights, turn signals, etc, you should consider the model specific item. I am working on a project.

👤It was 15 minutes of riding time. The coil pictured was very cheaply made. Do not buy.

👤Everything was installed easily, and my moped started and ran without any issues.

5. Carbhub Carburetor Mikuni Zongshen Thumpstar

Carbhub Carburetor Mikuni Zongshen Thumpstar

The dimensions of the carburetor are shown in the second and third pictures. Your old carburetor needs to look the same with their pictures. The new aftermarket VM22 26mm Carburetor is from CarbHub. You will get 1x inlet pipe Manifold, 1x air filter, and 1x carburetor. You will get 1x inlet pipe Manifold, 1x air filter, and 1x carburetor.

Brand: Carbhub

👤I've had this for a long time and was very hesitant to do this operation. The bike was still warm. I watched a few videos over the last two months, otherwise forget it. Remove the fuel hose, air filter, and two bolts. I didn't need new gasket or remove riser stem, I just pulled the car halfway out of the area. The cable end can come out. The long slot of the internal slider thing that houses the cable, spring and needle is only one way so you can't mess it up. Feed cable should be returned through the top cap, and the new one should be put on in reverse. There is a The part is difficult to hold because of the cap, spring cable, and compression of the spring, and the cable must be pulled tight until it can be pulled longer than the'slider' length. screw down cap on slide assembly Put main bolts back in, snug, add air filter, and fuel line back on. There is a Kick or push the electric start. There is a If you have the tool notes for the 140cc pit bike, you can use them for both. I removed the spark plug wire to get one of the main bolts out of the bike. There is a If you kick the tire one way or the other, we can remove the bolts from the fender. There is a This is the same thing as the oem, but my oem had a ton of hours on it so the bike was running poorly, this replacement was a night and day improvement. There is a The default setting should be ok, there's a fuel mix on the bottom. I suggest you replace the screw before you install the aftermarket fuel mix, they are longer and easier to adjust with a 4 paddle numbered thumb. There is a The side adjust that they call air mix, is also called idle adjust, and most people tell us that if you need to adjust, screw it all the way in and back out 1.5 to two revolutions/turns. There is a The fuel mix screw is the same. I hope this helps someone, if you want to find a pit bike or just plain 4 stroke fuel mix, try combinations of those terms in search, and those videos can further guide you in the process. There is a You'll never be afraid to replace a simple one like this one once you've done this. There is a Best to all.

👤Please read if you are using this with a 125 pit bike. * Before you install the new slide, make sure to remove the clip from the new slide with needle nose pliers. * Don't lose the washer. The needle should be removed. There are grooves at the top of the needle. There is a * Carefully remove the c clip and put it back on the top of the needle. Throttle response is great.

👤I bought this for my pit bike. Put this one on and it will kick off. Gave it gas and it got stuck. I tried to find an air/fuel mixture screw, but didn't see one. All I could find was a screw. I figured out how to get the bike to go by feathering the throttle. All weekend long, drape it around the pits. Unless you had the throttle pinned, you ran like garbage. When I took the car back off, I finally found the air/fuel screw, which had been missing for a long time. It's in the most inconvenient spot where you can't see it unless you are laying down. It is in front of the bowl. There is a I feel stupid for not taking the time to notice where this was before installing it. I think anyone would have missed it the same way I did. There is a This thing runs well after turning the screw out. The stock car is boring on the top end. It just keeps going! My cable adjustment might include a bit of my goofy idle. I didn't expect everything to be perfect, but this is a cheap Chinese bike. The filter it came with is something I don't like. It's a foam filter with a foam pretty filter. It's not ideal for dusty conditions. I'm going to try and find a paper element filter that is pretty.

6. Anbull Bicycle Engine Motorized Fuel Efficient

Anbull Bicycle Engine Motorized Fuel Efficient

The center to center spacing between the pins is approximately 7/16" wide. The engine is the 100CC. They used a generic version of the user manual for 80CC/100CC because they look similar. It comes with all the necessary hardware for easy installation. Heavy duty metal engine body. The max.speed was 48 km/h. Fuel type : 90#; N.W: 11 kilogram; G.W: 12 kilogram. It's for most 26" and 28" bikes. The frame should have clearance between the bottom brackets and the top bar of 9-11mm, and the diameter of the frame tubes should be 25-28mm. 50mm bore single piece cylinder, an upgraded CDI, Performance Speed Carburetor and more, high performance Speed Carburetor, silver anti-corrosion coating, high performance CDI with Yamaha components, improved magneto, high end allen bolts, improved gas cap. The mixing ratio for fuel and oil is good for the first 300-500 miles, but it is not good in the summer because of the hot weather. Please limit the riding time to a maximum of 1 hour for the first few rides to avoid any problems with the motor. If you have a question or are not satisfied with the product, please contact them. You can find the order by going to your account at Amazon. Click the seller name to enter the store page. Click "Ask a question".

Brand: Anbull

👤The bt 100 engine kit is uncommon to fine one of these engines. There are a few issues with the bt 100 engine kit. The magnet seems to be weak on one side. If I am able to find a replacement, I will have to.

👤It was a great way to get back and forth from work. It was amazing to feel that kind of power on a light frame bicycle. I added a 36 tooth sprocket and it definitely increased speed. It went from 30 mph to 35. I added a air filter and rubber motor mounts to make the motor less vibrate. All in a great product. It is very easy to put together.

👤The motor kit is great and there have been no issues so far. It's worth $200, but not if the exhaust isn't able to upgrade or change, my buddy built it for me and you can contact him on his Facebook page called - New motor bike builders.

👤They changed the engines. Either that or they have a few different ones. I have no issues with the motor. The chain was changed to a two bolt because I didn't use them enough. There is a great engine with lots of power.

👤I built and bought many engines because I use them for my food delivery job for two years now. The engine and accessories are the best yet. The bigger and better design of the carb makes it non-standard. If you buy a 100cc engine from bike berry, they will send the other ones. If you tighten the studs all the way in, they are not long enough to put bolts on. The other accessories were all of the same quality, and it looked like this guy took the time to package them. One thing I like about it is that the head came assembled, everyone else started making the customer do it, which is a pain in the ass. I just connected it to the bike. I learned that you have to be careful with the journal bearings, there is only a small film for them to ride on, and 3cc of oil in the crankcase, on my last 100cc from bike berry. Don't accelerate down hills when the engine is not running. I'll never find a 2 cycle engine that will get more than 5000 dollars worth of food deliveries done, but I will update when this engine takes a bad turn. It was an edited version. The motor took a bad hit on me. It has been 3 or 4 months of hard work delivering food. This engine has made me more money than any other. It was probably my fault since I forgot to put oil in my car before I left the gas station. It can happen in a few seconds if the circumstances add up. My mind is against me, and it's been so long since my back tire or my engine had ruined my day that it had to intervine! What an ass! I watched the destruction of the engines. I bought an extra one, I will be much more cautious and get an accurate picture of how much better this engine is than the rest.

7. Throttle Handle Clutch CRF100 LIYYOO

Throttle Handle Clutch CRF100 LIYYOO

Brand new and high quality, easy to install. The Baja Mini Bike has a Handle bar diameter of just over 7 inches. A hand grip fit for a dirt bike atv chopper. The cable is 48 inches in length. TheThrottle Cable Motor Bike Baja Mini Bike has aThrottle Handle and left brake lever. The motorized bicycle engine has a 2 stroke handlebar grips and genuine motor 125cc twist parts. There is a package with one. A pc brake lever, a pc left hand grip, a pc right hand grip, and a pc throttle tube were installed. The main image has the included accessories shown. If you have any questions, please feel free to contact them by email, they will solve it for you in the first time! If you have any questions, please feel free to contact them by email, they will solve it for you in the first time!

Brand: Liyyoo

👤The cable length for the Honda Z50 was too long so I had to route it under the seat so it would fit. The screws for the throttle assembly were not correct and they pulled the threads out of the metal. I had to find bigger ones. I had to use a grinder to cut the grooves in the cable for the brake lever because the cut out area for the cable was not made right. I would have returned the bike if my kids were anxious to ride it. Buying the least expensive part was a bad idea.

👤It seemed like everything was cool at first. It was ok to install. The first day the throttle cable snapped, we had to order a new one. I don't know if it was a user error or junk.

👤The cable broke after a few rides.

👤Got a mini bike. It's easy to install.

👤The handlebars on the Honda trail 90 need to be simplified. Everything seems to work well.

👤It worked, had issues with the cable coming undone.

👤The product is not as advertised, but it is too small. I would like to get the correct product. Sincerely. Rita J.

8. Minireen Harness Wiring Ignition Rebuild

Minireen Harness Wiring Ignition Rebuild

1x pull start and 1x claw whag. 50cc 70cc-110cc 125cc 140cc 160CC 4 Stroke Dirt Bikes are compatible with the wire harness kit. Kick Start only. The kit includes: a spark plug, a key switch, and a wire harness. Lifan, Loncin, tao tao, Ducar, Shineray, Zongshen, YX, and others are Chinese bikes. Easy to install Stator coil CDI spark plug for ATV. The inner core is pure copper, which is easy to conduct and does not burn out the line due to excessive temperature. The inner core is pure copper, which is easy to conduct and does not burn out the line due to excessive temperature.

Brand: Laxeem

👤I couldn't figure out how this wiring harness didn't help me.

👤I bought it to help my neighbor's kids rewire their quad and it shorted out the whole system and almost caught fire when we turned the key!

👤I used this to re-wire my yerfdog 3206 150cc gy6, although it states that it will only work with up to 125cc engines, I had no problems with it. There were only a couple of issues with this harness. The kill button does not have a back on it, this could cause you to be shocked if you grab it with out it on a handle bar and to ground out if it were to be close enough to the exposed metal of the handle bar, thus killing the engine. 2. I know the harness is only for a pit bike, but I would like to see a version that is extended or have separate extensions for purchase. It's a great deal.

👤The module was bad and not right for the rest of the assembly, I am thinking of retiring it and getting my money back, the module acts like there is no wiring in it.

👤I used this on a Honda atc185s (1981) and it works.

👤I thought I would need this harness, but found that the wiring was just as convenient, so I am going to keep this item. It's funny.

👤The pitster pro 125xjr has a wiring harness. After the first ride, the cdi decided to give up on me because it was only 15 minutes long.

👤I have a wire harness that works perfectly and it has connected to the other.

👤The harness is short and the connections are not in line with what I need.

9. YUEWO 2 Stroke Upgrade Electric Conversion

YUEWO 2 Stroke Upgrade Electric Conversion

The cross reference is BA20D, H6, S2. Before purchasing, please make sure the bulb is the same as the one pictured, and that the dimensions of the bulb work for your installation space. There is a headlight assembly without a bulb cap. 4. Not for the AC motor. Everything needed in order to assemble a motor bicycle is included in the 80cc 2-stroke bicycle motor kit. It's for most bikes with V-frame, such as mountain bikes, road bikes, cruisers, choppers. The electric motorbike kit has a single cylinder, air-cooling, 2-stroke 80cc single cylinder gasoline engine. It is made of first-rate steel material and has great strength and endurance, which can provide you with a long service life. The Capacitor discharge ignition method is safer and more stable than other methods. This type of ignition will not cause the wear and tear on the contact points when the bike engine is spinning at high speed. The design makes it easy to put together a bike, riders just need to fit the motor to the frame, connect the cables, and fill up the gas tank in order to be ready for their first ride. It can speed up to 50 km/h. It is almost as fast as a motorcycle or scooter. Your motorcycle can have better endurance with a 2L fuel tank and a single cylinder gas engine. It can speed up to 50 km/h. It is almost as fast as a motorcycle or scooter. Your motorcycle can have better endurance with a 2L fuel tank and a single cylinder gas engine.

Brand: Yuewo

👤Every thing was accounted for and great shape when the Positives-Package arrived. There is a The directions were hard to understand and the gold paint job was shabby.

👤I was worried about the paint but it arrived quickly and it was cool.

👤The paint on the gold model is terrible. I have to change it out of the box. The paint on the engine or tank will be gone if there is a gas spill. The paint peeling on Day 2 was crazy.

👤I bought this motor because of the color. It was not expecting to be a fast runner. It is a slow motor, but it started to come to life once it had some rides in. There is a I am happy with my bike, it is my cool looking, slow running, cruiser bike. I don't have to pedal!

10. Carburetor Filter Motorcycle Zongshen Thumpstar

Carburetor Filter Motorcycle Zongshen Thumpstar

The package has a carburetor, gasket,O-ring,Fuel Filter, and air filter. The engine side has an inner diameter of 26mm and an outer diameter of 48mm. The new Aftermarket VM22 26mm Carburetor is brand new. compatible with vm22 26mm. The car is 125cc. 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apollo, 125cc apoll If you have any questions, please feel free to contact them by email, they will solve it for you in the first time! If you have any questions, please feel free to contact them by email, they will solve it for you in the first time!

Brand: Liyyoo

👤The stupid plastic isolator they send with the carburetor is only 20mm. Someone tightened the fuel air screw. There is a brand new box. Also, note: You will need a new throttle cable if you install on an Apollo pit bike. Stock cables do not work with this car.

👤We were having a hard time trying to tune our TaoTao sr125. Two different types of carbs wouldn't tune properly for anything. We have this one. It started right up fist kick on choke and was almost dead on where it should be. It might be a bit rich on the main jet. I will do more testing. The gasket is not the right size. It is for a 20mm version of the smaller bicyle. I had an extra gasket around that was the right size. I think I got lucky. I was not going to run this set up with a smaller gasket. Take my word for it. If you don't want to be angry when you get your food, you need to buy a separate one. I think this is a good car for all the items included. The spark plug seems to work. I don't know how those will hold up, I used my own fuel lines. Everything seems good. Make sure your car isn't malfunctioning. Before I put it on, I took the carb apart. Check the jet size. If you use the intake manifolds they give in the kit, it seems like a good idea. I highly recommend you buy a separate intake manifolds gasket with the correct inner diameter. Happy Brapping!

👤This was the real thing. If you want a 125 to have lightning quick response and eventually grunt up to 60+mph, then this is the piece you want. Thank me later for spending the extra. I tried to find the cheaper one that was better. Don't waste your time, measure the current one, then order a mikuni. It was easy to install. It will be a breeze if you take a video apart while you watch it.

👤I have apollo 125cc and I love the product and would recommend it to anyone that wants to buy a over seas bike.

👤The Apollo 125cc dirt bike has a good quality and easy to install. The kit has a throttle cable needle that you need to change. I installed the needle that came with the kit. Don't use the parts in the kit for quick fixes. The bike is like a kitten. The quality of the car is good for the price. Buy it. Oh yes. It was shipped very fast.

👤The air filter was leaking right out of the box, but it was fine. There is a Sonic cleaned the car. It was back to ripping the Z50.

👤It shows that it is not the real thing. This is better than the stock car on Chinese bikes, but it is not very good. This item is exactly what you are paying for. It may or may not be worth it. This works well to get the bike up and running. This is not what you should get for the bike. A real Japanese Mikuni is years ahead in quality.

11. Throttle Accelerator Handle Assembly TaoTao

Throttle Accelerator Handle Assembly TaoTao

The item is made of plastic. The same cool looks can be obtained at great prices. Fit for 70cc and 90cc. The ATVs have "handlebars" such as Lifan, SUNL, Redcat, eagle, and Buyang. Please make sure this part fits your motorcycle before ordering. The cableinner length is 46.5 inches. The thumb controller has handle bars. High quality. The cable is made of metal and the grip is made of rubber. Installation is easy and quick. It's convenient for assembly and disassemble. The package contains 1 Thumb Controller, 1 pc Accelerator Cable, 4 cs Cable Ties, 1 pc Screwdriver, and 1 pc wrench. The package contains 1 Thumb Controller, 1 pc Accelerator Cable, 4 cs Cable Ties, 1 pc Screwdriver, and 1 pc wrench.

Brand: The Revenant

👤I replaced the twist throttle on my moto with this. The kids had blisters. The cable was perfect length and this alleviated all that.

👤The China quads come with 125cc and 49cc. 90cc works for all of them.

👤The quality is nice, but the throttle doesn't have enough throw. It doesn't pull the cable all the way.

👤I need to fit my atc 200.

👤It was made of Chineseum. I put it on a 229CC Dirtbike and it works on a wide variety. It is a very cheap fix.

👤It works like it should.

👤Do not buy this for less than 100. It is too short.

Summary

What is the best product for bicycle motor kit 125cc?

Bicycle motor kit 125cc products from Kunray. In this article about bicycle motor kit 125cc you can see why people choose the product. Huri and Mingdun are also good brands to look for when you are finding bicycle motor kit 125cc.

What are the best brands for bicycle motor kit 125cc?

Kunray, Huri and Mingdun are some of the best brands that chosen by people for bicycle motor kit 125cc. Find the detail in this article. Topemai, Carbhub and Anbull are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com