Best Bicycle Cell Phone Holder Aluminum

Holder 16 Aug 2022 10+ Comments Open

1. Motorcycle Adjustable Shockproof Compatible Smartphone

Motorcycle Adjustable Shockproof Compatible Smartphone

The back lock is made of PC material and metal and will not let your phone fall. Powerful Clamp. It does not bow down due to bumps. The tighter the grip, the greater the force. Soft Silicone is in the accent section to make sure it won't scratch your handlebars and phone. The silicone part of the handlebar clip can be used to avoid the rotation. The Pro Impact Resistance has high strength PC, Back Lock, Powerful Clips, Soft Silicone. It allows you to ride anywhere you please with bumps or jumps on your phone. The Handlebar Diameter is 0.7" and the Smart Phone Size is 4.5" to 6.8"

Brand: Joyroom

👤I bought this one because someone else has it. Works well for them. The mount does a good job of holding the smaller phones. The only complaint about those phones is that the screen doesn't stay with the direction you put it in. I don't intend on staring at the screen, so I didn't find it a big deal that it vibrates out of the optimal viewing angle very easily. If I had a smaller phone, I would give it a couple of stars. There is a It doesn't fit larger phones. The bottom part is at an angle. Again, it's fine for the smaller phones. A lot of the phones are not much wider than they are. The corner pieces come out at an angle, which causes them to not grip the corners. There is a bit of space in the picture. The phone in the picture is a s20 ultra. The last picture shows it all the way to one side, so you can shake the phone out of it. I have no doubt that vibrating down the road won't push it to that point. It is very easy to pull the phone out of the lock once it gets to that point. The last picture shows it barely touching the corner. It takes a slight twist of the phone to get it to come out. Would it fall on the road? Maybe, maybe not. I'm not willing to take the chance of finding out. I wanted something that held the phone in place. This isn't that. I should not be able to remove the phone from the mount. There is a The fact that I don't feel confident that my phone won't be broken on the side of the highway is a definite dealbreaker. The design needs some tweaking to be more secure. There is a The bar is very strong. It is easy to install and remove, and it can be tightened up. It's easy to put together, even though it comes needing to be assembled. If I had a smaller phone, it would probably be a decent mount.

👤It holds my phone. Especially on trips. I use it on my motorcycle. There is a The only problem is. No matter how much I tighten it. There is a The position of my phone is easy to change when I use it. There is a When I put my phone in the holder. There is a I really like it.

👤I put it on my motorcycle handle bars. It holds the phone in a tight place and the lock is good if you want to feel safe.

👤It will hold phone solid if the top corners are curved.

👤I like the fact that this device is easy to install, holds my phone securely and easy to use, and it doubles as a phone stand when not attached to my motorcycle handle bar.

👤I used this on my motorcycle, even though I didn't use the lock. It still held the phone solid.

2. Motorcycle Universal Anti Shake Compatible Smartphone

Motorcycle Universal Anti Shake Compatible Smartphone

The bike mount on the Super Stable is military grade. The Andobil bike phone mount has a non-slip/scratch-resistant silicone cushion and flexible clamping arms, so it will not fall off even in sudden braking or steep roads. You can come with double shock-absorbing Silicone bands, which can be stretched up to 4 times to hold your phone, not only protect your phone in the craziest adventure. The ball joint gives you the ideal viewing angle and allows you to switch between portrait and landscape view in a matter of seconds. The open-face design allows you to fully experience the joy of riding or sporting, because it has full-screen access and different lengths' clamps avoid pressing the volume key. The universal phone holder for bicycle has a clip that fits most phones. It's compatible with the iPhone 12. Mini/11 Pro/11 Pro Max/SE/Xs Max/XR/Xs Plus/6 Plus/7 Plus Plus/7/7 plus/6 plus/6 plus/4 There are more than one, including the following: the S20/S21/Note20/A51/S8/S8 Plus/S7/S10/S10 Plus/S9 Plus/Note 8, the S9 Plus/Note 8, the S10 Plus/S9 Plus It is easy to install the bike cell phone holder on the handlebars. The phone holder for bike handlebars has a scratch-free rubber pad and can be adjusted to fit any bike. Andobil puts the customer's experience in the first and insists on making high-quality products. Please let them know if you have any usage problems or product suggestions. They will improve their products. There is a one-year hassle-free service. If you have a problem with andobil's phone bike holder, please mail them and they'll get to you in 12 hours. package box, nut, phone mount base, and user manual.

Brand: Andobil

👤During the time of COVID-19, I bought a bike so I could get some exercise. I was more than happy to review this mount when I was approached by this company. There is a The mount is made of rubber. It has an additional rubber phone holder to hold larger phones. Up to 7 in length and 4.5 in width. The device is very flexible. I can change my phone's orientation with ease. There is a The phone is secured to the bike. The amount of slip is limited by groves of rubber teeth. My daughter attached it to the baby stroller. She won't give it back.

👤The skyforce95 is very easy to install and mount, and it is secure and easy to change.

👤The Andobil holder broke off when I was riding on a bumpy road at 20 miles per hour. I contacted Andobil and asked if I could get a replacement. It took me a long time to use it because I was lucky to have my phone undamaged. I have been using the new unit for about 3 months and it has been the same thing. The Andobil piece holding my phone went flying and landed in the middle of a busy road when the unit broke in half. I was able to stop cars from riding over the phone after pivoting my bike. The phone was saved from damage by the protective case. It might be a freak event. Two times...no.

👤Delivery was on time. The packaging looks good. Assembly and instructions were easy to follow. The product is well placed on the handlebars. I haven't had any issues with the connections or the straps, it's plastic I think it is a good product. It is brand new. I would feel comfortable using this on a road or mountain bike. The bike can be moved to different bikes depending on my needs, and I like that it's quick. I love their proactive and responsive customer service. I would be very comfortable buying this again and working with this company.

👤I bought this for my new phone less than a month ago. It was easy to install. I only used it once, when I received an email from Andobil that another customer had complained about their mount breaking. Even though I had no problem with my original order, Andobil wanted to send me a new mount. The new mount is easy to install and I received it very quickly. It is easy to use. I highly recommend. Customer service is top notch and the product is high quality.

👤The mount works well for me. The rubber band holds my G5 in place. The side brackets are sturdy and l-shaped to provide additional safety. The handlebar is large, easy to tighten, and the soft rubber pads are attached to the brackets so it can't move, which was a problem with my old mount.

👤I've used a number of phone holders for my motorcycle, and this one is the best. It is low profile and blends in nicely with my ape hangers. It is easy to adjust the phone.

3. Visnfa Adjustable Universal Accessories Smartphones

Visnfa Adjustable Universal Accessories Smartphones

The latest design. The bicycle phone mount has an exclusive design. Installation and uninstallation of mobile phones can be achieved quickly. The simple design makes you feel different. VisnFA motorcycle phone holder is made of plastic and is shockproof. No matter what the road is like, it's stable. The rubber pads on the arm are designed to protect your phone. The bicycle phone holder has an open design that allows full access to the phone screen controls and buttons. You can use the mobile phone gps function at any time. Shoot and record your travel moments, don't block the camera. Simply tighten the mounting screws to fix the motorcycle phone mount on the handlebars. It only takes a few seconds. The quick switch to lock should be closed when the brackets are adjusted to fit the size of the phone. Leave enough space to avoid damaging the phone. This phone holder is compatible with all 3.5- to 7-inch phones. It is suitable for various types of bicycles, mountain bikes, motorcycles, shopping carts, and electric scooters.

Brand: Visnfa

👤The holder is great once installed. I didn't think the instructions were user-friendly. I installed it by messing with it. It's easy to access the controls on my phone. I made a good phone video. It's easy to access the controls on the phone and I used it to stream music while riding, which is a little risky but shows that it's safe.

👤I bought this to use on my golf push cart so I could keep my phone handy. I used a mount that used rubber bands along the top and bottom of the phone to hold it. It worked, but the rubber bands made it hard to take a picture of the local wildlife and I had to take the phone off every time. The mount makes it easy to use, just flip the cam lever and the phone slides right out, then flip it back and the phone is secure in place. Even if you don't flip the cam, the phone will stay in the mount. When you turn the dial to adjust the width of the mount, it moves very slowly and takes a lot of turns to move the mounting arms. I thought they weren't moving but they were. It's not sure how large a phone it will hold, but it's a problem to hold an Apple phone in a leather case.

👤I returned the unit because of how it was mounted. I have an odd ledge at the goose neck that caused issues and didn't provide the secure mount I wanted, plus it almost interfered with my cycle computer. I bought this to make sure I didn't get lost on unfamiliar trails. This is an ideal mount for most applications. The way the phone is secured is very secure. The angle adjustment is great. For my situation, it wasn't ideal, but I would recommend this in most applications. There is a My other observations... The dial is not easy to use and the adjustments are slow. You won't need to mess with it once you have it set for your phone. The rubber pads are for different thicknesses of handlebars. It was not easy, but it is the only way to do it. Do I need more than 2? I need 3, I can't slip it in easily, so I need to remove it and try again. You won't need to mess with it once you figure it out. I would recommend it, but I had to use a different mount method.

👤The Pro Sits is very firm on the handlebars. Even with a triple layer protective case, the clamp holds my Note 8 superbly secure. If you have a phone with a stylus pen, be sure to remove it before you go for a ride. There is a Con. The upper section has some play even with the ball being tightened. There is a Overall. Even though it has a flaw, it's a good phone mount. This product is recommended by me.

👤I wanted a simple phone holder for my bike as it is electric and I like to plot my route as well as log the speed and the time. There is a I did not have to use the rubber pieces for my setup on the 31.8 handlebar because I used the phone holder as a base. There is a If you press the size and remove the knob, you can widen the mount to fit most modern phones that are very wide. With my electric bicycle, I've gone as fast as 21 mph, and my phone stayed put, and never had an issue.

4. Lamicall Bike Phone Holder Mount

Lamicall Bike Phone Holder Mount

Easy installation. The upgrade mountain bike phone mount is easy to install. There are various types of bicycles, motorcycles, stroller, shopping cart, electric scooter, indoor treadmill, indoor bike. The handlebar diameter is 1.57" (15-40mm). Wide Compatibility Universal bike cell phone stand with thickness up to 15mm, like the iPhone 13 Pro Max and the iPhone 12 Pro Max Mini Xs. The Plus 7 6s, the S10e S9 S8, the Note 9 8 and the Oneplus are some of the cell phones. The protection is shockproof. Silicone pads keep your phone from being scratched and vibrating, and this one hand operation bike phone mount comes with them. The motorcycle phone mount holds your phone. The cellphone can be adjusted to a horizontal or vertical screen. It's convenient to answer the phone, play music, and use the gps. Sturdy and safe. The motorcycle phone holder has a special shape. It keeps your cellphone out of harms way even on a bumpy road.

Brand: Lamicall

👤Works well! I trust my phone to be on my motorcycle. Doesn't move or shake. It is made with strong materials. I would suggest riding a Harley. I was worried that it would be too heavy, but it was built to fit in your phone and be safe. I hope this helps.

👤Over the years, I've used these holders to mount my phones to motorcycle handlebars. Security is important. I've owned several styles, the last one being a RAM X mount. The rubber bands were secured, but the clamps interfered with my volume buttons. Let's face it, the rubber bands are a pain. The Lamicall phone holder is similar to others I've owned but is more elegant. The mount is easy to slip the phone into. There is no need for rubber bands. It is possible to vary from protrait to landscape depending on one's direction of travel. It tilts so that the camera lens are protected from bugs if you are on a naked bike. I like the thing. I bought a second motorcycle so I don't have to swap. It's big enough for an iPhone 12 Pro Max.

👤Stay away from this model. There were two pieces out of the box. The unit is not designed correctly. The ball must be tightened to hold it together. I would not have gotten the ball into the sockets with the tightened nut if I had not owned a vice. The lock nut could not be threaded once the sockets were seated because the threads were not aligned. I use this model on my motorcycle. The phone can slip in the top lock even when it's locked. The Lifeproof case cracked when the unit shook so much. I'm still looking for a phone holder. Don't buy it.

👤It was thrown on a rally. It didn't shake on me once after an hour trip. I can still see the dash if I put a 12 PlusMax in this thing.

👤I dropped my phone while on the trails because I had wasted money on cheaper products. Other products are made of plastic and I have found replacements that don't last. The Lamicall holder is flexible and sturdy. I can switch between my motorcycle and mountain bike. The metal bolt on the clamp creates grip on the handlebars. The springs hold the phone in place and the holder rotates to allow for flexibility. It has padding on the edges of the phone to protect it from debris. Overall very satisfied with the product and price.

👤I used this for my 09 super glide needles and I love it! Even with the sound of a motorcycle. The design is very sturdy. If I need another down the road, I will definitely buy again. I have an otter box with an Apple device. It is easy to get it out. It is my otter box. I have no complaints.

👤The build quality here would never hold up to a motorcycle. The mounting system for a motorbike is made with plastic and steel that feels brittle, and it would break if it were damaged by the speed, bumps, and vibrations of a motorbike. The mounts are bound to wear out over time. The lock doesn't seem to do much to keep your phone in place when you're off-roading. If you want to use this on a street bicycle, then hell. Yes! It will do.

5. BRCOVAN Motorcycle Handlebar One Touch Aluminum

BRCOVAN Motorcycle Handlebar One Touch Aluminum

One-handed operation. The bike and motorcycle phone mounts have a lock and switch design. Put in or take out the phone and hold it in one hand. It is easy to adjust the mobile phone to a horizontal or vertical screen. Enjoy a ride for free. The bike phone mount has a special shape that can wrap four corners of your phone tightly. The telescopic arms and base are super sturdy. The bike phone holder is perfect for holding your phone while riding. Silicone pads keep your phone from scratches and vibration, and the bicycle phone mount also has shockproof protection. The design of the phone bike mount and phone camera is non-contact. The camera should not be squeezed or scratched while riding. Easy installation. The phone mount can be installed on the mirror frame. The rubber ring inserts provide a snug fit and protect the mounting surface. You can either add or remove the rubber ring pad. It is convenient to install the motorcycle phone holder on the rear-view mirror frame with a rear-view mirror mounting bracket. The motorcycle phone holder is compatible with 4'' - 7'' smartphones. The phone holder is mounted on the handlebars with a diameter of 22mm-32mm. It's suitable for installation on bikes, motorcycles, mountain bikes, scooters and other vehicles.

Brand: Brcovan

👤I needed a cell phone holder that was reliable for our trikes. I had a holder for the car, and wanted something similar. One that is spring loaded in that when you push your phone into the holder, the arms on either side snap onto it and hold it tightly. I looked for one that was similar to that. The BRCOVAN Phone Mount was similar to the one in my car. There is a It is mounted on what you mount it on. Every installation is usually different according to the acronym "YMMV". The mount is universal and can be adapted to most mounting situations. BRCOVAN supplies an additional mounting bracket to enhance the mounting locations if needed, and another mount did not. The decision for me was made by the additional brackets. I chose the BRCOVAN mount since it was included, but I didn't need it. How does it hold up when mounted? The answer is fine. I bought 2 of them and both were very tight. There is one possible "fly in the ointment" so to speak, that is not a flaw. It has to do with the phone and case. We have cell phones with protective cases. The thick phone cases made by OtterBox may make your phone taller than the mount can handle. I have to make sure that I push the phone back into the mount, because there is a red button on the mount that I have to use to hold the phone in place. Two independent arms at each corner hold the phone. The whole top of the phone has a single curved bar at each end. Once you know that the two arms at the bottom and the one at the top are securely in place, you can mount your phone. It's a great ride with no worries in my case. The phone didn't move a bit when I traveled on a very rough gravel road. The mount was tightly secured. I can't say if it would work on a motorcycle, but I would think it would work. If you use a protective case on your phone, then this mount should work for you, but make sure you check the phone's height first. Your phone's protective case can make a big difference in how well it holds. Without a protective case on your phone, the BRCOVAN mount is as perfect as you can ask for. This also applies to almost every cell phone mount on the market. I am very happy with my purchase. I have attached pictures of my installation. I hope this is helpful.

👤I had a difficult time getting my scooter installed because it is so large, but with a little tweaking I was able to get it. It is very easy to stop the phone in and out and that is the best part. The screws are very small and have signs of oxidation from the heavy rain so I would advise you to put some Silicone over them when you first install them. Silicone should be put on the little screws. I have a case for my phone and it fits into the phone brackets very well.

6. Motorcycle Universal ,Aluminum Adjustment Smartphones

Motorcycle Universal %EF%BC%8CAluminum Adjustment Smartphones

The phone holder will allow your screens to tilt. It's a good idea to avoid the sunlight and to switch the landscape or portrait view on your phone. Most of the mobile devices have a screen of 47 inches, such as the iPhone, Nesus, and other. The light-weight and solid aluminum alloy base and sturdy construction ensure the super stability. Adding Rubble pads to the solid clamps will hold the phone securely and prevent it from dropping or scratching. There are more rubble pads to protect your handle bar. No other tools are required for easy installation. If you are not satisfied within 90 days, you will get a full refund.

Brand: Fjqxz

👤The device is made of good materials and holds a phone. The included rubber pads are useless because they fall off during riding, not to mention your phone's case will protect the phone from rubbing the cradle and will probably grip better than the pads anyway. You may need to disassemble the balljoint retainer screws to hold the inner ball against the inside of the joint to tighten it. The ball-joint is the major flaw. 5 miles of rough roads will cause the joint to loosen and tilt the phone, so it has no locking teeth or texture to affix it to the housing. I couldn't turn the lock nut further because my hands were wet and I couldn't get my fingers around it well enough to turn it. I tried using blue Locktite on the threads of the screws and the balljoint, but it didn't work. The phone loosened while it was tilted. It's more than annoying to constantly fiddle with the clamp. I used superglue on the balljoint. I don't care if it's permanent. I can focus on riding safely because it will stay where I have it set. This isn't the phone cradle for you if you're thinking about hiring a mechanic.

👤The mount is made of aluminum. It's very study and light. The phone is held very tight. The ball joint isn't perfectly rounded, which makes it difficult to adjust the position. It will stay after it's adjusted. The cushions for the 4 grips are made of double-sided tape. I don't know how long they will last. Hard metal may scratch the phone without those cushions.

👤It works well with a small amount of manipulation. The bars on the walker were different from the bars on the bike. It was mounted well.

👤It holds the phone well but has one caveat. The rubber pieces that protect the phone are hard to fall out of. You will lose the protective pad if you are not careful. I will have to find a solution to keep these pieces in place.

👤I had to add some rubber to the bar. It wasn't big enough for a s8 but worked on s5.

👤Holds phone in place. The holder is designed for a phone that does not have a case. I have a small box that holds the phone in place, and it's not small. I bought a rubber strap to complement the holder. I use it on my motorcycle.

👤I've been using this for a while on my moped for the price and it's not bad at all, but the hardware is cheap and it rattles its self into peace. The loud noise that comes from my phone mount is the newest issue I have experienced.

👤The phone holder does not hold the phone during a bike ride. The phone would fall out if I didn't tighten the screw. Returned the product after a ride. Do not recommend.

7. Universal Motorcycle Handlebar Adjustable Compatible

Universal Motorcycle Handlebar Adjustable Compatible

Powerful secure GRIP_RUBBERIZED CLIP & SILICON BELTS: The design of motorcycle phone mounts has been improved. The brand new bike phone mount could be adjusted to meet any direction you need. The new anti-shake design is improved for any road situation. The bicycle phone holder had a lock on it. There is unrestricted company mobility. Any phone up to 3.5” wide can be fit in the universal bike phone mount. The bike phone mount was made of metal and plastic, and it was easy to use.

Brand: Asunby

👤I bought this for my motorcycle, but didn't get to use it because my mom stole it. This is the first mount that fits and is rock solid, after weeks of searching. If I could, I would give 6 stars.

👤I have one of those bikes and I am very happy. It had no mount for your phone, and the Power Adapter was laid on the floor or in a drawer. Someone else bought this mount for use with the Peloton. It's easy to set up and can hold onto any tube surface. When I put my phone in it, I can use it to hold the power transformer safe away from the cats and dogs. #WinWin

👤I put this on the front light bar of my quad to hold my phone and use my gps for riding the trails. The video was to show the terrain I have taken. My phone was in place. The corner tab holders wouldn't fit over my phone, so I used the 2 side holders and they did the job very well. This purchase was very happy with.

👤The product is very functional. The rubber bands that are supposed to protect the phone are useless. I had to remove my protective cover to get them on. They slip off the phone corners after doing that. Even with the hard cover on, the two spring loaded bars on the sides do a good job of securing the phone. I've ridden many miles with just them securing the phone. People know how much a Harley shakes. The phone is secure. One suggestion to the manufacturer would be to put a small shelf at the bottom for extra security. There is a It is easy to mount and gyrate to many positions.

👤I have tried a lanyard and it doesn't work. Just used it after buying it. Works well. Very strong. I have to keep my phone in my back pocket or on the cart for it to fall through.

👤The thing was great at first. It's perfect for my commute and travel. After only a week of use, the whole thing to the bike started slipping. When I tighten the knob, it tightens and then free spins and loosens up. The threads have been removed. After a week! I liked it at first. It held the phone well for road biking. It wouldn't be a good idea to ride a mountain bike. I have to remove it first because they have been telling me to do so. There is a Don't buy from this company.

👤It does what it is supposed to do for me. It holds my phone while I drive. I end up doing a lot of things while I'm out. I used to have a suction cup arm that I used to attach to the window to hold my phone, but it was bulky and didn't always hold. I got this to do the job and it works great. It doesn't get in the way of cables because it grips from the sides. I don't use corner band things to hold my phone. I've never used this on a bike or in an active way.

8. ROTTO Motorcycle Aluminum 360°Rotation Adjustable

ROTTO Motorcycle Aluminum 360%C2%B0Rotation Adjustable

Quality all aluminum construction is more sturdy than those plastic mounts. Hold the phone, insert or remove it. Touch ID is available and the mount can be rotation. The bike phone mount can be adjusted to fit almost all phones. It is easy to install, only a short time. There are two different ones, one is for 22.2mm handlebar and the other is for 25.4mm handelbar. The standard handlebars do not need to be adjusted. To protect the phone from scratches and shocks, come with some rubber pads which are attached to the inside of the fixed claws.

Brand: Rotto

👤I have been using this for almost six months. I trusted it from the beginning with my phone. About 3 of these aluminum holders were tried on. This preferred this one for the shape of the phone surface. I use an Otterbox Commuter on my phone and it works perfectly. There is a I had a plastic phone holder that broke, so I will never buy a plastic one again. Sturdy, no wiggle. Hold the phone securely. I have full access to all buttons, but it doesn't loosen during my hour long rides. I will update if I find any.

👤This is a high quality mini-vise. It makes it easy to steer a bike by the stem and see the landscape on the phone. You don't have to get a special case for your phone. It will work with almost any case. It would work with any phone. The price was a steal. It comes with rubber pads that you apply to the inner corners. Nice touch. It's pretty tight. Good looking and simple. You should get one for your cockpit. I wish the knob was blackened. It is easy to use and reliable so far. They should be sold in every bike shop.

👤My phone fell out of the cell phone holder. Before I start each ride, I tighten the screw. I tried to tighten the screw while riding, as I had noticed that it had loosened more recently. At the beginning of my last ride, it fell out and damaged my phone. I have been using rubber bands to hold the phone in place but now I have to tighten the screw every time I ride. I didn't give it a single star because I live in a area with bad road quality. If you lived in an area where you didn't have to worry about the roads, you will be fine.

👤The unit doesn't rely on cheap rubber bands to hold the phone in place. The phone is screwed into the holder after it is screwed onto the handle bars. A little plastic and a lot of aluminum. Quality all around. Get this one. You won't be disappointed.

👤I have been using this mount on my bike for two months. There is a It was perfect! There is a It's super sturdy. The installation is two minutes. I have no problems with the mount on my Ebike, it's made to handle off road use. There is a My phone is an Apple product. One of the larger phones will handle my phone.

👤I have issues with my phone caddy again. These things are not made for phones in cases. I have had the phone go out on rides. My phone would have been destroyed if it weren't for my case. This would hold firm if you weren't using a case.

👤This phone holder is amazing. This product is great, but I didn't get compensated for it. It's a solid metal construction. I don't have to worry about my phone falling off my bike and I can use my phone in any direction to watch videos while I ride. It won't loosen its grip over time because it's not held on with stretchy rubber. The product was very good.

9. Tiakia Bike Phone Mount Motorcycle

Tiakia Bike Phone Mount Motorcycle

The new design of the phone holder will not obscure the screen of the phone. It's convenient to answer calls, play music and ride. It's a good partner for bicycles and motor travel. All your doubts can be solved by Tiakia's. Choose a holder! Peace of mind! The bike mount has a fixing screw that can lock the phone. You can use the free frame. The drop rate of the brackets is zero. It can make sure that your phone doesn't get lost under the most dangerous conditions. It's suitable for round handlebars with a diameter of 22-33mm. Enjoy the ride, let's free their hands. The traditional method of installation of the cell phone holder for bike saves 1/3 of the time, but it is tool-free. The process of fixing or removing the phone is very simple and takes 3 seconds. After 5,000 rotation tests, the metal rotating mechanism is still good. It's flexible to use, and it can be used without removing the Phone Mount. The motorcycle holder can be used as a holiday gift for couples, friends, and family, and is suitable for cell phones of up to 7.2" in width. The motorcycle phone mount is suitable for many phones. The MI A1/A2 is called the lite. The REDMI Note 6 Pro/6A/Note 5 Plus/S2 is one of them. The high-quality aluminum alloy makes it harder to break, and it extends the service life by 12 times. The bike holder is made from high quality materials, it's not easy to fade, and more beautiful, let's together become a stylish outdoor sportsman! The high-quality aluminum alloy makes it harder to break, and it extends the service life by 12 times. The bike holder is made from high quality materials, it's not easy to fade, and more beautiful, let's together become a stylish outdoor sportsman!

Brand: Tiakia

👤Installation of this phone holder was easy, I couldn't be happier with it. I got the orange and black and it matches my Duke.

👤To hold a phone, the side mounts are shallow. The phone wouldn't work with this holder. Too bad. It would have been great if it wasn't for the mistake.

👤cheap plastic was used to make the last phone cradle. When I dropped my bike, it broke into pieces. I said no more plastic. The cradle is made of solid aluminum. I would like to see improvement. The plastic liner is made of plastic. I said no more plastic because it doesn't do the job of keeping the cradle in place. I replaced it with a piece of rubber that prevents the metal tube from slipping around it. Please don't use plastic and replace it with a rubber piece. The cradle is solid other than the above. The phone stays put if you affix it well. I've had the phone on my bike for a while and it stayed put.

👤Add on for your bike. I love the way it looks. I stress that you use the strap that comes to make sure you have the sides secured. There is a It will handle anything if it can handle the Chicago streets.

👤It was easy enough. This is on a Honda CB 650 motorcycle. I chose it because it has a very narrow mounting point, because I didn't have enough room on my clip ons to mount it. It seems very sturdy. I tested it at speeds over 100 mph and it did not budge. There is a lot of adjustments to be made to make it fit like you want it to, because it has around 10 or so positions that it will click into. I used to use these types of phone holders for my mountain bikes only and would use the RAM mounts or quad lock on motorcycles, but I think this is just as good, just as secure at a fraction of the cost. It may take a few more seconds than the RAM mount to put the phone in and take out, but $25 is a deal. BH.

👤I have a otter box on my phone and it holds it right. It is difficult to get on this product, but it is not bouncing off when you ride. The rubber straps fit my 13 max. Right. If you do mountain biking and have a smaller phone, it is the must has holder. Your phone is on the ground. This is a light full aluminum. This thing is amazing. People notice the quality of the product when I ride with out the phone. This is not plastic, it is all aluminum. My phone has never fallen off and is very well designed. One thing I like about adjusting with Allen nuts is that they stay tight. You can't change or slip the size once you lock it. The plastic one in my car is always righted by me. This is a good buy. Your friends will want to know where you bought it, so keep one in your cart. If you use it for gps maps, you can rotation the holder vertically or horizontally.

10. AONKEY Bike Phone Mount Motorcycle

AONKEY Bike Phone Mount Motorcycle

The ball joint design can adjust the bicycle phone mount in different direction to provide optimal viewing angle even on bright day. Shrinkable arms and a rubber belt make it easy to take a phone off on the mountain road. It can fix the handlebar with an upgrade mount with an aluminum alloy bolt and soft rubber pad, it is suitable for bike, motorcycle, electric bike, shopping chart, scooter, stroller, treadmill. Simply screw the aluminum bolt to fix the handlebars, and press the button on the side to open the arms. The Aonkey motorcycle phone holder can give you full access to the phone screen. Their universal cell phone holder for bike is compatible with all sizes of phones.

Brand: Aonkey

👤I bought one because my phone was blocking the treadmill display. I could easily transfer the mount to my bike after my run. I ordered a second one because the cost was so reasonable. The mount for weight lifting is being relocated because of the adjustability for viewing angle. Someday it will leave the house for use in an environment where it is not a problem. It works great indoors. The lower flap works well as a backup to the side grips but it will interfere with the phone jack on the bottom center. Charge before or after the workout. One hand release button. This phone mount is very good.

👤The thing is very durable and awesome. I haven't purchased anything like this in a long time and I can't say enough about the quality of this phone holder. It is very easy to hold my phone in an otter box defender case. The tuff material is very strong. If you are looking for a phone holder for your motorcycle, bike or anything similar, I highly recommend this holder.

👤The mount is made from sturdy material. I have only used it inside to mount my phone, but I would use it outside if I needed to. For increased security, you can use the elastic bands to mount the phone in the arms. I use a rubber case for my phone.

👤The IC Life Fitness bikes that my gym uses for the Spin classes are perfect for this product. I have used it twice now and wondered how I had not had this mount before. I don't use the gel holder part since the bike is stationary, but it makes teaching spin class easier.

👤I use my upright bike to watch training and entertainment videos on my cellphone. There is a The fit and quality of the device are great. I am very satisfied.

👤It is easy to install and keep my phone in place. It's attached to my exercise machine and it makes it so much more fun to listen to music, watch my TV show, or check out websites on it.

👤It keeps my phone stable when I use it on my rides. Climbing and decending 3000+ feet on my local mountains has posed no problem for this phone holder. The claw grasp system is better than other options.

👤I have a pop sockets on my phone that I use every day, so my options were to find an open-backed phone mount. I was able to find a spot on the left handle bar that made it easy to use.

11. Bike Motorcycle Phone Mount Universal

Bike Motorcycle Phone Mount Universal

We mean out and out universal, which means mount any phone to any bike or motorcycle with tubular handlebars. The holder can fit any device up to 3.7" wide and all handlebars from 0.2" to 1.6" in diameter. There are no tools required for installation. AJUSTABLE GRIP. Simply adjust and secure your phone to any angle and position that suits you, and enjoy the comfort of your ride! Extra secure and soapy absorbent clip with silicone belts hold device firmly and securely. The bands wrap the corners of the phone. They hold tight, make your most extreme race to make the phone fall out, be sure it won't! While your device is mounted, you have full phone access. You can use your phone for music. You don't need to unmount your phone or ipod. You should keep your hands on the handlebars. 100 to be safe! If you don't like your new bike phone mount, just contact them and they will make it right.

Brand: Caw.car Accessories

👤My daughter uses her new power wheelchair with the Bike & Motorcycle Phone Mount. The powerchair didn't have a place to attach a bag or basket to carry the phone. My daughter has cerebral palsy and is able to use her left arm and hand. She doesn't have much control of her right hand. In the third picture, you can see that the Bike & Motorcycle Phone Mount doesn't affect her ability to reach the controls to drive her power chair while allowing her phone to be tilted and/or rotated so she can use it with her left hand. The Bike & Motorcycle Phone Mount can be used to solve two phone problems: carrying the phone from place to place and being able to use it wherever she goes. 5 stars for easy to install, 5 stars for Sturdy, 5 stars for reasonable price, 5 stars for Adaptable to other uses, and 5 stars for Really Useful. Fifty stars is more or less.

👤It took me a while to find the best location on my motorcycle handlebars, but I think I have found it. The claw is very strong and easy to tighten. The hold down straps are mostly contained within the unit and pull out only when needed. I don't put a phone in it for short trips.

👤I have a rubber over plastic phone cover on my phone which makes it a bit bulky. The corners will not be wrapped. The phone has been on my motorcycle for the past 2 months, and I have attached the phone holder to the motorcycle. It is easy to remove. I would recommend it.

👤The construction is very high quality, it feels rugged, and I passed my rugged "shake it until you break it" even with the S9 attached. I was worried about putting on my motorcycle because I thought the rubber bands would break and I didn't know if the bar claws would work. All of the positive reviews are well deserved.

👤The number of positive reviews here is so high that I am astonished. There are 4 possible failure points in this product, but only 3 were initially visible. The claw that grabs the handlebars seems pretty good. 2. The ball/socket joint allows for tilt and rotation. 3. The elastic corners hold the phone. There is a I was a few minutes into my ride when I noticed the side brackets were too close to one of the buttons. I pushed the base of the phone up to make sure the button was clear. Turns out it was 4. The base has a plastic slide mount on it. If it fell off on a smooth road cycling ride with a gentle nudging on the phone, I can't see how it would last 5 minutes on a mountain bike, motorcycle, etc.

👤The rubber bands on the mount started to slip off after a month on my bike. They seem stretched and won't hold on anymore. I tried to clean them in case there was dust, but it didn't help. The top pin that holds the "claws" together fell out while I was riding. It was unnerving to have my phone fly off while I was riding. It was a good start, but not a long lasting product.

Summary

What is the best product for bicycle cell phone holder aluminum?

Bicycle cell phone holder aluminum products from Joyroom. In this article about bicycle cell phone holder aluminum you can see why people choose the product. Andobil and Visnfa are also good brands to look for when you are finding bicycle cell phone holder aluminum.

What are the best brands for bicycle cell phone holder aluminum?

Joyroom, Andobil and Visnfa are some of the best brands that chosen by people for bicycle cell phone holder aluminum. Find the detail in this article. Lamicall, Brcovan and Fjqxz are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com